MSDS-273C
September 2006
MATERIAL SAFETY DATA SHEET
CIPADOR E-200 PART B (CLEAR)
SECTION 1 - PRODUCT INFORMATION
Manufacturer: CPD Construction Products
219 Connie Crescent # 13
Concord, Ontario L4K 1L4
Product Identifier: CIPADOR E-200 Part B (clear)
Application and Use: Roller Applied Epoxy Floor Coating
Product Description: Two component Epoxy Coating
Regulatory Classification:
WHMIS Information: Class D, Division 2, Subdivision B, Class E, Corrosive.
Transportation of Dangerous Goods Information:
Alkalamines, Corrosive Liquid, N.O.S. (Trimethyl hexa methylene diamine) Class 8 UN 2735 PG III
EMERGENCY TELEPHONE NUMBERS
CANUTEC: (613) 996-6666
SECTION 2 - HAZARDOUS INGREDIENTS
Ingredients CAS# %(weight) LD/50 Route/Species
Amine & Epoxy Resin Copolymer Not available 60-100 Not available
Benzyl Alcohol 100-51-6 15-40 -1230mg/kg (Oral-Rat)
-4000mg/M鲁(Rat-Inhalation)
SECTION 3 - PHYSICAL DATA
Physical State: Liquid Specific Gravity: 1.01 @ 23掳C (73掳F)
Vapour Pressure: 0.70mm Hg @ 21掳C (70掳F) Solubility in Water: Slight (0.1-1%)
Boiling Point: n/a Freezing/Melting Point: n/a
Viscosity: 300 cps @ 23掳C (73掳F) Vapour Density: n/a
Evaporation Rate: n/a % Volatile: (VOC): 0.0gm/l
Odour: Characteristic amine Appearance: Clear amber mobile liquid
SECTION 4 - TOXICOLOGICAL PROPERTIES
NATURE OF HAZARD
INHALATION, ACUTE: Irritating to respiratory tract. Coughing and chest pain may result. Inhalation of aerosol, mist
or fog may cause harm.
INHALATION, CHRONIC: Refer to acute inhalation.
EYE CONTACT: Contact with undiluted product with the eyes quickly causes irritation and pain and may cause burns,
necrosis and permanent injury. Burns of the eye may cause blindness. Product vapour in low concentration can cause
lacrimation, conjunctivities and corneal edema when absorbed into the tissue of the eye from the atmosphere. Corneal
edema may give rise to a perception of 鈥淏lue Haze鈥? or 鈥淔og鈥? around lights. The effect is transient and has no known
residual effect.
/...2
MSDS-273C
September 2006
SKIN CONTACT: Contact of undiluted product with skin quickly causes irritation and pain and may cause burns,
necrosis and permanent injury.
INGESTION, ACUTE: May cause bleeding of the gastrointestinal tract and vomiting of blood.
INGESTION, CHRONIC: Refer to acute ingestion.
Toxicological Date: No data.
SECTION 5 - FIRST AID MEASURES
INHALATION: If inhaled, remove victim to fresh air. If breathing is difficult, administer oxygen. If breathing has
stopped, give artificial respiration. Keep person warm, quiet, and get medical attention.
EYE CONTACT: Flush with water for at least 15 minutes while forcibly holding eyelids apart to ensure complete
irrigation of all eye and lid tissue. Get medical attention.
SKIN CONTACT: Wash with soap and water. Launder contaminated clothing before reuse. Contact a physician if
irritation develops.
INGESTION: Get medical attention immediately. Do not induce vomiting. Remove stomach contents by gastric suction
only as directed by medical personnel. Never give anything by mouth to an unconscious person.
SECTION 6 - PREVENTIVE MEASURES
PERSONAL PROTECTION: Avoid smoking, drinking or eating in use. Avoid contact with eyes, skin and clothing.
Discard contaminated leather.
ENGINEERING CONTROLS: General ventilation; local exhaust ventilation as necessary to control any air
contaminants, to within their TLV鈥檚, in the use of this product.
HANDLING, STORAGE AND SHIPPING: Do not use sodium nitrite or other nitrosating agents in formulations
containing this product. Cancer causing nitrosamines could be formed. Store away from heat and ignition sources. Store in
a cool, dry and well ventilated area. Keep away from acids, alkalis and oxidizing agents. Keep containers closed when not
in use. Do not store in iron or other reactive metal containers.
SPILL CONTROL AND DISPOSAL: Avoid all skin contact. Avoid breathing vapours of heated materials. Keep away
from heat, sparks and open flame. Wash thoroughly after handling.
LAND SPILL: Eliminate source of ignition. Keep public away. Prevent additional discharge of material, if possible to do
so without hazard. Prevent spills from entering sewers, watercourses or low areas. Contain spilled liquid with sand or
earth. Do not use combustible materials such as sawdust. Recover by using a suitable absorbent.
WATER SPILL: Remove from surface by skimming or with suitable absorbents. If allowed by local authorities and
environmental agencies, sinking and/or suitable dispersants may be used in confined water.
SECTION 7 - FIRE AND EXPLOSION DATA
Flashpoint and Method: >100掳C (T.C.C.)
Auto ignition Temperature: Not Available
Flammable Limits: Not Available
FIRE FIGHTING: Personnel in vicinity and downwind should be evacuated. Fire fighters should wear approved self
contained breathing apparatus and full protective clothing.
/...3
MSDS-273C
September 2006
HAZARDOUS COMBUSTION PRODUCTS: May generate toxic or irritating combustion products. Ammonia, oxides
of carbon (CO, CO2) and oxides of nitrogen.
SECTION 8 - REACTIVITY DATA
GENERAL: This product is stable and hazardous polymerization will not occur under normal conditions.
INCOMPATIBLE MATERIALS AND CONDITIONS TO AVOID: Contact with mineral acids ( such as sulfuric,
phosphoric etc.), alkalis, organic acids (ie; acetic acid, citric acid etc.), reducing agents, reactive metals (ie; sodium,
calcium, zinc etc.), sodium or calcium hypochlorite, materials reactive with hydroxyl compounds, amines, nitrites,
nitrosating agents such as perchlorates or nitrates.
HAZARDOUS DECOMPOSITION: Irritating and toxic fumes at elevated temperatures. Ammonia when heated.
Oxides of nitrogen. Organic acid vapours. Aldehydes. Nitric acid. Nitrosamines. Nitrogen oxides can react with water
vapours to form corrosive nitric acid. Oxides of carbon (CO, CO2).
SECTION 9 - PREPARATION
Prepared By: R.J. Green
Plant Manager
CPD Construction Products
Concord, Ontario L4K 1L4
|