SECTION 2 - HAZARDOUS INGREDIENTS
The following component data is defined in accordance with sub-paragraph 13(a) (i) to (iv) or paragraph 14(a) of the
Hazardous Products Act.
No raw materials in this product are required to be listed as defined by the Hazardous Products Act.
SECTION 3 - PHYSICAL DATA
Physical State: Liquid Specific Gravity: 1.0 @ 20掳C (approx.)
Vapour Pressure: Not applicable (Same as water) Solubility in Water: Infinite dilution
Boiling Point: 100掳C (approx.) Freezing/Melting Point: 0掳C (Approx.)
Viscosity: 10-15 cps @ 20掳C (Approx.) Vapour Density (AIR=1): > 1.0
Evaporation Rate (n-Butylacetate=1) < 1.0 % Volatile: 84-85%
Coefficient Water/Oil Distribution: Not applicable PH: 11.0 @ 20掳C
Odour: Faint ammonia odour Appearance: Milky white liquid
SECTION 4 - TOXICOLOGICAL PROPERTIES
NATURE OF HAZARD
INHALATION: Excessive exposure to vapours or mists may cause irritation of eyes, nose and throat.
EYE CONTACT: This product may be an eye irritant.
SKIN CONTACT: This product may cause defatting and irritation of skin upon prolonged or repeated exposure.
INGESTION: Stomach pain may result. No other information available on effects of ingestion.
OCCUPATIONAL EXPOSURE LIMIT: No limit established.
/...2
MSDS-251
September 2006
SECTION 5 - FIRST AID MEASURES
INHALATION: Remove victim to fresh air. If irritation persists consult a physician.
EYE CONTACT: Immediately flush eyes with water for at least 15 minutes holding open eyelids. Since this product is
an emulsion a film may form on eyes if coagulation occurs. In all cases seek medical attention.
SKIN CONTACT: Wash with water. Use mild soap if available. If irritation persists seek medical attention.
INGESTION: Contact a physician immediately.
SECTION 6 - PREVENTIVE MEASURES
PERSONAL PROTECTION: Where prolonged and/or repeated skin and eye contact is likely to occur, wear safety
glasses with side shields, PVC or neoprene full length gloves and full work coveralls as the minimum protection. If mist is
generated during application the appropriate full face respirator should be worn by workmen. Portable eye wash stations
should be made available at all jobs sites.
ENGINEERING CONTROLS: Not necessary for outdoor jobs or indoor jobs unless ventilation is extremely poor. For
confined areas with poor ventilation power ventilation may be required.
HANDLING, STORAGE AND SHIPPING: Keep containers closed when not in use. Handle and open containers with
care. Store under normal warehouse conditions. DO NOT ALLOW PRODUCT TO FREEZE. This product is an emulsion
therefore freezing could coagulated the emulsion and rupture the container.
SPILL CONTROL AND DISPOSAL: For small spills flush area with water before emulsion dries. For large spills
contain with sand or earth. Add sodium or calcium chloride to coagulated the spilled product. Place residue into
appropriate containers and dispose of in accordance with all Federal, Provincial and municipal regulations. Do not flush
spilled product into storm sewers, sanitary sewers or water coarses. After clean up of the spill area the remaining latex
may be flushed with water before it dries.
SECTION 7 - FIRE AND EXPLOSION DATA
Flashpoint and Method: Not applicable.
Auto ignition Temperature: Not applicable.
Flammability Limits: Not applicable.
GENERAL HAZARDS: None. Non-combustible product as supplied, however if water is boiled off in a fire the resin
solids will burn generating toxic gases.
FIRE FIGHTING: Not applicable.
HAZARDOUS COMBUSTION PRODUCTS: Not applicable
SECTION 8 - REACTIVITY DATA
GENERAL HAZARDS: This product is stable and hazardous polymerization will not occur.
INCOMPATIBLE MATERIALS AND CONDITIONS TO AVOID: None.
HAZARDOUS DECOMPOSITION: Under severe thermal degradation, low molecular weight organic compounds will
be formed.
SECTION 9 - PREPARATION
Prepared By: R.J. Green
Plant Manager
CPD Construction Products
Concord, Ontario L4K 1L4
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP