MSDS-54

                                                September 2006



                                    MATERIAL SAFETY DATA SHEET

                                       CPD LATEX ADHESIVE



SECTION 1 - PRODUCT INFORMATION

Manufacturer: CPD Construction Products

              219 Connie Crescent # 13

              Concord, Ontario L4K 1L4



Product Identifier: CPD Latex Adhesive



Application & Use: Additive to concrete, grout and mortar to improve overall physical properties. Also used as

an adhesive to bond concrete and grout overlays to concrete, steel and wood substrates. This product is generally

applied by direct addition with water to the hydraulic cement mix.



Product Description: Styrene-Butadiene Latex Emulsion.



Regulatory Classification

WHMIS Information: Not controlled.



Transportation of Dangerous Goods Information: Not regulated.



EMERGENCY TELEPHONE NUMBERS:

CANUTEC: (613) 996-6666



SECTION 2 - HAZARDOUS INGREDIENTS

The following component data is defined in accordance with sub-paragraph 13(a) (i) to (iv) or paragraph 14(a) of

the Hazardous Products Act.

No raw materials in this product are required to be listed as defined by the Hazardous Products Act.



SECTION 3 - PHYSICAL DATA

Physical State: Liquid                                    Evaporation Rate (n-Butylacetate=1) < 1.0

Specific Gravity: 1.00 @ 20°C (approx.)                   % Volatile: 70-72%

Vapour Pressure: Not applicable (Same as water)           Coefficient Water/Oil Distribution: Not applicable

Solubility in Water: Infinite dilution                    PH: 11.0 @ 20°C

Boiling Point: 100°C (approx.)                            Odour: Faint ammonia odour

Freezing/Melting Point: 0°C (Approx.)                     Appearance: Milky white liquid

Viscosity: 5-10 cps @ 20°C (Approx.)

Vapour Density (AIR=1): > 1.0





SECTION 4 - TOXICOLOGICAL PROPERTIES

NATURE OF HAZARD

INHALATION: Excessive exposure to vapours or mists may cause irritation of eyes, nose and throat.



EYE CONTACT: This product may be an eye irritant.



SKIN CONTACT: This product may cause defatting and irritation of skin upon prolonged or repeated exposure.



INGESTION: Stomach pain may result. No other information available on effects of ingestion.



OCCUPATIONAL EXPOSURE LIMIT: No limit established.







                                                                                                               /...2

                                                  MSDS-54

                                                September 2006



SECTION 5 - FIRST AID MEASURES

INHALATION: Remove victim to fresh air. If irritation persists consult a physician.



EYE CONTACT: Immediately flush eyes with water for at least 15 minutes holding open eyelids. Since this

product is an emulsion a film may form on eyes if coagulation occurs. In all cases seek medical attention.



SKIN CONTACT: Wash with water. Use mild soap if available. If irritation persists seek medical attention.



INGESTION: Contact a physician immediately.



SECTION 6 - PREVENTIVE MEASURES

PERSONAL PROTECTION: Where prolonged and/or repeated skin and eye contact is likely to occur, wear

safety glasses with side shields, PVC or neoprene full length gloves and full work coveralls as the minimum

protection. If mist is generated during application the appropriate full face respirator should be worn by workmen.

Portable eye wash stations should be made available at all jobs sites.



ENGINEERING CONTROLS: Not necessary for outdoor jobs or indoor jobs unless ventilation is extremely

poor. For confined areas with poor ventilation power ventilation may be required.



HANDLING, STORAGE AND SHIPPING: Keep containers closed when not in use. Handle and open

containers with care. Store under normal warehouse conditions. DO NOT ALLOW PRODUCT TO FREEZE.

This product is an emulsion therefore freezing could coagulated the emulsion and rupture the container.



SPILL CONTROL AND DISPOSAL: For small spills flush area with water before emulsion dries. For large

spills contain with sand or earth. Add sodium or calcium chloride to coagulated the spilled product. Place residue

into appropriate containers and dispose of in accordance with all Federal, Provincial and municipal regulations.

Do not flush spilled product into storm sewers, sanitary sewers or water courses. After clean up of the spill area

the remaining latex may be flushed with water before it dries.



SECTION 7 - FIRE AND EXPLOSION DATA

Flashpoint and Method: Not applicable.

Auto ignition Temperature: Not applicable.

Flammability Limits: Not applicable.



GENERAL HAZARDS: None. Non-combustible product as supplied, however if water is boiled off in a fire the

resin solids will burn generating toxic gases.



FIRE FIGHTING: Not applicable.



HAZARDOUS COMBUSTION PRODUCTS: Not applicable



SECTION 8 - REACTIVITY DATA

GENERAL HAZARDS: This product is stable and hazardous polymerization will not occur.



INCOMPATIBLE MATERIALS AND CONDITIONS TO AVOID: None.



HAZARDOUS DECOMPOSITION: Under severe thermal degradation, low molecular weight organic

compounds will be formed.



SECTION 9 - PREPARATION

Prepared By: R.J. Green

             Plant Manager

             CPD Construction Products

             Concord, Ontario L4K 1L4