MSDS-287A
October 2006
MATERIAL SAFETY DATA SHEET
CIPADOME SPARK PROOF PART B
SECTION 1 - PRODUCT INFORMATION
Manufacturer: CPD Construction Products
219 Connie Crescent # 13
Concord, Ontario L4K 1L4
Product Identifier: CIPADOME SPARK PROOF Part B
Application and Use: Trowel applied epoxy floor topping.
Product Description: Three component spark proof epoxy floor topping.
Regulatory Classification:
WHMIS Information: Class D, Division 2, Subdivision B, Class E, corrosive
Transportation of Dangerous Goods Information:
Amines, liquid corrosive N.O.S. (Amino Terminated Polyether) Class 8, UN 2735 PG III
EMERGENCY TELEPHONE NUMBERS
CANUTEC: (613) 996-6666
SECTION 2 - HAZARDOUS INGREDIENTS
Ingredients CAS# %(weight)
Amino Terminated Polyether 9046-10-0 30-60 LD50-1660mg/kg(Oral-Rat)
Nonyl Phenol 25154-52-3 7-13 LD50-1620mg/kg(Oral-Rat) LD50-2140mg/kg(Rabbit-Skin)
Tris 2,4,6 (Dimethyl 90-72-2 3-7 LD50-1200mg/kg(Oral-Rat) LD50-1280mg/m鲁(Rabbit-Skin)
Aminomethyl) Phenol
Bisphenol A 80-05-7 10-30 LD50-3250mg/kg (Oral-Rat) LD50-3000mg/kg (Rabbit-Skin)
Diethylene Triamine 111-40-0 10-30 LD-50 - Not Available
SECTION 3 - PHYSICAL DATA
Physical State: Liquid Specific Gravity: 0.980
Vapour Pressure: 0.70mm Hg @ 21掳C (70掳F) Solubility in Water: n/a
Boiling Point: n/a Freezing/Melting Point: n/a
Viscosity: 200 cps @ 23掳C (73掳F) Vapour Density: n/a
Evaporation Rate: n/a % Volatile: (voc): 10gm./l
Odour: Characteristic amine Appearance: Clear amber mobile liquid
SECTION 4 - TOXICOLOGICAL PROPERTIES
NATURE OF HAZARD
INHALATION, ACUTE: Irritating to respiratory tract. Coughing and chest pain may result. Inhalation of aerosol, mist
or fog may cause harm.
INHALATION, CHRONIC: Refer to acute inhalation.
/...2
MSDS-287A
October 2006
EYE CONTACT: Contact of undiluted product with the eyes quickly causes irritation and pain and may cause burns,
necrosis and permanent injury. Burns of the eye may cause blindness. Product vapour in low concentration can cause
lacrimation, conjunctivities and corneal edema when absorbed into the tissue of the eye from the atmosphere. Corneal
edema may give rise to a perception of 鈥渂lue haze鈥? or 鈥渇og鈥? around lights. The effect is transient and has no known
residual effect.
SKIN CONTACT: Contact of undiluted product with the skin quickly causes and pain and may cause burns, necrosis and
permanent injury.
INGESTION, ACUTE: May cause bleeding of the gastrointestinal tract and vomiting of blood.
INGESTION, CHRONIC: Refer to acute ingestion.
Toxicological Date: No Data
SECTION 5 - FIRST AID MEASURES
INHALATION: If inhaled, remove victim to fresh air. If breathing is difficult, administer oxygen. If breathing has
stopped, give artificial respiration. Keep person warm, quiet, and get medical attention.
EYE CONTACT: Flush with water for at least 15 minutes while forcibly holding eyelids apart to ensure complete
irrigation of all eye and lid tissue. Get medical attention.
SKIN CONTACT: Wash with soap and water. Launder contaminated clothing before reuse. Contact a physician if
irritation develops.
INGESTION: Get medical attention immediately. Do not induce vomiting. Remove stomach contents by gastric suction
only as directed by medical personnel. Never give anything by mouth to an unconscious person.
SECTION 6 - PREVENTIVE MEASURES
PERSONAL PROTECTION: The selection of personal protective equipment varies depending upon conditions of use.
When handling product wear long sleeves, chemical resistant gloves and safety glasses with side shields. Where splashing
during mixing may occur wear full face shield. Where concentrations in air may exceed the occupational exposure limits
and where engineering work practices or other means of exposure reduction are not adequate, approved respirators may be
necessary to prevent overexposure by inhalation.
ENGINEERING CONTROLS: General ventilation; local exhaust ventilation as necessary to control any air
contaminants, to within their TLV鈥檚, in the use of this product.
HANDLING, STORAGE AND SHIPPING: Avoid all skin contact. Avoid breathing vapours of heated materials. Keep
away from heat, sparks and open flame. Wash thoroughly after handling.
SPILL CONTROL AND DISPOSAL: Consult an expert on the disposal of recovered material. Ensure disposal in
compliance with government requirements and ensure conformity to local disposal regulations. Notify the appropriate
authorities immediately. Take all additional action necessary to prevent and remedy the adverse effects of the spill.
LAND SPILL: Eliminate source of ignition. Keep public away. Prevent additional discharge of material, if possible to do
so without hazard. Prevent spills from entering sewers, watercourses or low areas. Contain spilled liquid with sand or
earth. Do not use combustible materials such as sawdust. Recover by using a suitable absorbent.
WATER SPILL: Remove from surface by skimming or with suitable absorbents. If allowed by local authorities and
environmental agencies, sinking and/or suitable dispersants may be used in unconfined water.
/...3
MSDS-287A
October 2006
SECTION 7 - FIRE AND EXPLOSION DATA
Flashpoint and Method: >100掳C (T.C.C.)
Auto ignition Temperature: Not available
Flammable Limits: Not available
GENERAL HAZARDS: Combustible liquid; may release vapours that form combustible mixtures at or above the flash
point. Toxic gases will form upon combustion.
FIRE FIGHTING: Personnel in vicinity and downwind should be evacuated. Fire fighters should wear approved self
contained breathing apparatus and full protective clothing.
HAZARDOUS COMBUSTION PRODUCTS: May generate toxic or irritating combustion products. Ammonia, oxides
of carbon (CO, CO2) and oxides of Nitrogen.
SECTION 8 - REACTIVITY DATA
GENERAL: This product is stable and hazardous polymerization will not occur under normal conditions.
INCOMPATIBLE MATERIALS AND CONDITIONS TO AVOID: Excessive heating. Avoid contact with acids and
reactive polymers.
HAZARDOUS DECOMPOSITION: Irritating and toxic fumes at elevated temperatures. Ammonia when heated. No
hazardous decomposition when stored under normal warehouse conditions.
SECTION 9 - PREPARATION
Prepared By: R.J. Green
Plant Manager
CPD Construction Products
Concord, Ontario L4K 1L4
|