MSDS-274C
September 2006
MATERIAL SAFETY DATA SHEET
CIPADOR N-300 PART B (CLEAR)
SECTION 1 - PRODUCT INFORMATION
Manufacturer: CPD Construction Products
219 Connie Crescent # 13
Concord, Ontario L4K 1L4
Product Identifier: CIPADOR N-300 Part B (clear)
Application and Use: Roller Applied Epoxy Floor Coating
Product Description: Two component Epoxy Coating
Regulatory Classification:
WHMIS Information: Class D, Division 2, Subdivision B., Class E, corrosive.
Transportation of Dangerous Goods Information:
Alkylamines, corrosive liquids N.O.S. (Trimethylhexamethylenediamine) Class 8 UN 2735 PG III
EMERGENCY TELEPHONE NUMBERS
CANUTEC: (613) 996-6666
SECTION 2 - HAZARDOUS INGREDIENTS
Ingredients CAS# (Pbw%) LD/50 Route/Species
Benzyl Alcohol 100-51-6 30-60 LD50-1230mg/kg (Rat-Oral) LC50-4000mg/M鲁(Rat-Inhal.)
Amine & Epoxy Resin Copolymer Not available 40-70 LD50-Not Available LC50-Not Available
Tris-2,4,6 (Dimethyl-aminomethyl) 90-72-2 1-5 LD50-1200mg/kg(Rat-Oral) LC50-Not Available
Phenol
SECTION 3 - PHYSICAL DATA
Physical State: Liquid Specific Gravity: 1.04 @ 23掳C (73掳F)
Vapour Pressure: 0.70mm Hg @ 21掳C (70掳F) Solubility in Water: Slight (0.1-1%)
Boiling Point: n/a Freezing/Melting Point: n/a
Viscosity: 1000 cps @ 23掳C (73掳F) Vapour Density: n/a
Evaporation Rate: n/a % Volatile: (voc): 0.0gm/L
Odour: Characteristic amine Appearance: Clear amber mobile liquid
SECTION 4 - TOXICOLOGICAL PROPERTIES
NATURE OF HAZARD
INHALATION, ACUTE: Irritating to respiratory tract. Coughing and chest pain may result. Inhalation of aerosol, mist
or fog may cause harm.
INHALATION, CHRONIC: Refer to acute inhalation.
/...2
MSDS-274C
September 2006
EYE CONTACT: Contact with undiluted product with the eyes quickly causes irritation and pain and may cause burns,
necrosis and permanent injury. Burns of the eye may cause blindness. Product vapour in low concentration can cause
lacrimation, conjunctivities and corneal edema when absorbed into the tissue of the eye from the atmosphere. Corneal
edema may give rise to a perception of 鈥淏lue Haze鈥? or 鈥淔og鈥? around lights. The effect is transient and has no known
residual effect.
SKIN CONTACT: Contact of undiluted product with skin quickly causes irritation and pain and may cause burns,
necrosis and permanent injury. May be absorbed by skin.
INGESTION, ACUTE: May cause bleeding of the gastrointestinal tract and vomiting of blood.
INGESTION, CHRONIC: Refer to acute ingestion.
TOXICOLOGICAL DATA: No data.
SECTION 5 - FIRST AID MEASURES
INHALATION: If inhaled, remove victim to fresh air. If breathing is difficult, administer oxygen. If breathing has
stopped, give artificial respiration. Keep person warm, quiet, and get medical attention.
EYE CONTACT: Flush with water for at least 15 minutes while forcibly holding eyelids apart to ensure complete
irrigation of all eye and lid tissue. Get medical attention.
SKIN CONTACT: Wash with soap and water. Launder contaminated clothing before reuse. Contact a physician if
irritation develops.
INGESTION: Get medical attention immediately. Induce vomiting or remove stomach contents by gastric suction only
as directed by medical personnel. Never give anything by mouth to an unconscious person.
SECTION 6 - PREVENTIVE MEASURES
PERSONAL PROTECTION: Avoid smoking, drinking or eating in use. Avoid contact with eyes, skin and clothing.
Discard contaminated leather.
ENGINEERING CONTROLS: General ventilation; local exhaust ventilation as necessary to control any air
contaminants, to within their TLV鈥檚, in the use of this product.
HANDLING, STORAGE AND SHIPPING: Avoid all skin contact. Avoid breathing vapours of heated materials. Keep
away from heat, sparks and open flame. Wash thoroughly after handling.
SPILL CONTROL AND DISPOSAL: Eliminate source of ignition. Keep public away. Prevent additional discharge of
material, if possible to do so without hazard. Prevent spills from entering sewers, watercourses or low areas. Contain
spilled liquid with sand or earth. Do not use combustible materials such as sawdust. Recover by using a suitable
absorbent.
LAND SPILL: Eliminate source of ignition. Keep public away. Prevent additional discharge of material, if possible to
do so without hazard. Prevent spills from entering sewers, watercourses or low areas. Contain spilled liquid with sand or
earth. Do not use combustible materials such as sawdust. Recover by using a suitable absorbent.
WATER SPILL: Remove from surface by skimming or with suitable absorbents. If allowed by local authorities and
environmental agencies, sinking and/or suitable dispersants may be used in unconfined water.
/...3
MSDS-274C
September 2006
SECTION 7 - FIRE AND EXPLOSION DATA
Flashpoint and Method: >100掳C (T.C.C.)
Auto ignition Temperature: Not Available
Flammable Limits: Not Available
FIRE FIGHTING: Personnel in vicinity and downwind should be evacuated. Fire fighters should wear approved self
contained breathing apparatus and full protective clothing. Use alcohol foam and dry chemical to extinguish fires. C02
may be used for small fires.
HAZARDOUS COMBUSTION PRODUCTS: May generate toxic or irritating combustion products. Ammonia, oxides
of carbon (CO, CO2) and oxides of nitrogen.
SECTION 8 - REACTIVITY DATA
GENERAL: This product is stable and hazardous polymerization will not occur under normal conditions.
INCOMPATIBLE MATERIALS: Contact with mineral acids ( such as sulfuric, phosphoric etc.), alkalis, organic acids
(ie; acetic acid, citric acid etc.), reducing agents, reactive metals (ie; sodium, calcium, zinc etc.), sodium or calcium
hypochlorite, materials reactive with hydroxyl compounds, amines, nitrites, nitrosating agents such as perchlorates or
nitrates.
HAZARDOUS DECOMPOSITION: Irritating and toxic fumes at elevated temperatures. Ammonia when heated.
Oxides of nitrogen. Organic acid vapours. Aldehydes. Nitric acid. Nitrosamines. Nitrogen oxides can react with water
vapours to form corrosive nitric acid. Oxides of carbon (CO, CO2).
SECTION 9 - PREPARATION
Prepared By: R.J. Green
Plant Manager
CPD Construction Products
Concord, Ontario L4K 1L4
|