MSDS-287
October 2006
MATERIAL SAFETY DATA SHEET
CIPADOME SPARK PROOF PART A
SECTION 1 - PRODUCT INFORMATION
Manufacturer: CPD Construction Products
219 Connie Crescent # 13
Concord, Ontario L4K 1L4
Product Identifier: CIPADOME SPARK PROOF Part A
Application and Use: Trowel applied epoxy floor topping.
Product Description: Three component conductive epoxy floor topping.
Regulatory Classification:
WHMIS Information: Class D, Division 2, Subdivision B
Transportation of Dangerous Goods Information: Not Regulated
EMERGENCY TELEPHONE NUMBERS
CANUTEC: (613) 996-6666
SECTION 2 - HAZARDOUS INGREDIENTS
Ingredients CAS# % (pbwt) LD/50 Route/Species
Diglycidyl Ether of Bisphenol A 25068-38-6 60-100 30g/kg(Oral-Rat )
2-Methyl Phenol Glycidyl Ether 2210-79-9 7-13 4000mg/kg (Rat-Oral) >4500mg/kg(Rabbit-Skin)
Aromatic Hydrocarbon 64742-94-5 1-5 LD50-N/A
Carbon Black 1333-86-4 7-13 >8000mg/kg(Oral-Rat)
SECTION 3 - PHYSICAL DATA
Physical State: Liquid Specific Gravity: 1.18 @ 23掳C (73掳F)
Vapour Pressure: n/a Solubility in Water: Insoluble
Boiling Point: n/a Freezing/Melting Point: n/a
Viscosity: 3,000 cps @ 23掳C (73掳F) Vapour Density: n/a
Evaporation Rate: n/a % Volatile: (voc): 10gm/l
Odour: mild Hydrocarbon Appearance: Black mobile liquid
SECTION 4 - TOXICOLOGICAL PROPERTIES
NATURE OF HAZARD
INHALATION, ACUTE: Not considered a problem unless heated to high temperatures.
INHALATION, CHRONIC: Refer to acute inhalation.
EYE CONTACT: Irritating.
SKIN CONTACT: This product may cause skin irritation and/or sensitization after repeated contact.
INGESTION, ACUTE: Low toxicity, causes irritation.
/...2
MSDS-287
October 2006
INGESTION, CHRONIC: Low toxicity, causes irritation.
Toxicological Data: No data
SECTION 5 - FIRST AID MEASURES
INHALATION: If inhaled, remove victim to fresh air. If breathing is difficult, administer oxygen. If breathing has
stopped, give artificial respiration. Keep person warm, quiet, and get medical attention.
EYE CONTACT: Flush with water for at least 15 minutes while forcibly holding eyelids apart to ensure complete
irrigation of all eye and lid tissue. Consult a physician.
SKIN CONTACT: Wash with soap and water. Launder contaminated clothing before reuse. Contact a physician if
irritation develops.
INGESTION: If swallowed DO NOT induce vomiting. Get prompt medical attention.
SECTION 6 - PREVENTIVE MEASURES
PERSONAL PROTECTION: The selection of personal protective equipment varies depending upon conditions of use.
When handling product wear long sleeves, chemical resistant gloves and safety glasses with side shields. Where splashing
during mixing may occur wear full face shield. Where concentrations in air may exceed the occupational exposure limits
and where engineering work practices or other means of exposure reduction are not adequate, approved respirators may be
necessary to prevent overexposure by inhalation.
ENGINEERING CONTROLS: General ventilation; local exhaust ventilation as necessary to control any air
contaminants, to within their TLV鈥檚, in the use of this product.
HANDLING, STORAGE AND SHIPPING: Avoid all skin contact. Avoid breathing vapours of heated materials. Keep
away from heat, sparks and open flame. Wash thoroughly after handling.
SPILL CONTROL AND DISPOSAL: Consult an expert on the disposal of recovered material. Ensure disposal in
compliance with government requirements and ensure conformity to local disposal regulations. Notify the appropriate
authorities immediately. Take all additional action necessary to prevent and remedy the adverse effects of the spill.
LAND SPILL: Keep public away. Prevent additional discharge of material, if possible to do so without hazard. Prevent
spills from entering sewers, watercourses or low areas. Contain spilled liquid with sand or earth. Do not use combustible
materials such as sawdust. Recover by using a suitable absorbent.
WATER SPILL: Remove from surface by skimming or with suitable absorbents. If allowed by local authorities and
environmental agencies, sinking and/or suitable dispersants may be used in unconfined water.
SECTION 7 - FIRE AND EXPLOSION DATA
Flashpoint and Method: >100掳C (T.C.C)
Auto ignition Temperature: Not Available
Flammable Limits: Not Available
GENERAL HAZARDS: Combustible liquid; may release vapours that combustible mixtures at or above the flash point.
Toxic gases will from upon combustion.
/...3
MSDS-287
October 2006
FIRE FIGHTING: Use water spray to cool fire exposed surfaces and to protect personnel. Use foam or dry chemical to
extinguish fire. Respiratory and eye protection required for fire fighting personnel. A self-contained breathing apparatus
(SCUBA) should be used for all indoor fires and any significant outdoor fires. For small outdoor fires, which may easily
be extinguished with a portable fire extinguisher, use of an SCUBA may not be required.
HAZARDOUS COMBUSTION PRODUCTS: Fumes, smoke, and carbon monoxide, carbon dioxide and various
hydrocarbons.
SECTION 8 - REACTIVITY DATA
GENERAL: This product is stable and hazardous polymerization will not occur under normal conditions.
INCOMPATIBLE MATERIALS AND CONDITIONS TO AVOID: Excessive heating. Avoid contact with strong
acids bases and oxidizers.
HAZARDOUS DECOMPOSITION: None under normal warehouse storage conditions.
SECTION 9 - PREPARATION
Prepared By: R.J. Green, Plant Manager
CPD Construction Products
Concord, Ontario L4K 1L4
|