MSDS 241
September 2006
MATERIAL SAFETY DATA SHEET
CIPADOR E- 400 PART A BASE
SECTION 1 - PRODUCT INFORMATION
Manufacturer: CPD Construction Products
219 Connie Crescent #13
Concord, Ontario, L4K 1L4
Product Identifier: CIPADOR E-400 PART A BASE
Application and Use: Pour applied Two Component Joint Filler for saw cut joints or preformed concrete joints.
Product Description: Two component thermosetting flexible epoxy joint filler..
NOTE: There are two separate MATERIAL SAFETY DATA SHEETS for this product. There is one MSDS for the
base component, PART "A" and another MSDS for the curing agent component PART "B". Read both MATERIAL
SAFETY DATA SHEETS before using this product. This MSDS is for the BASE (PART "A") only.
Regulatory Classification:
WHMIS - Class D Division 2 Subdivision B (Skin Sensitizer)
Transportation of Dangerous Goods Information: NOT REGULATED (Part A only)
EMERGENCY TELEPHONE NUMBERS
CANUTEC: (613) 996-6666
SECTION 2 - HAZARDOUS INGREDIENTS
The following component data is defined in accordance with subparagraph 13(a) (i) to (iv) or paragraph 14(a) of the
Hazardous Products Act.
NAME (pbw)% CAS
4,4 Isopropyl 100% 25068-38-6 LD50-11.4 gm/kg (Oral-Rat)
Denediphenol Epichlorohydrin Resin LD50-20 ml/kg (Skin Rabbit) LC50-Not available
SECTION 3 - PHYSICAL DATA
Physical State: Liquid Specific Gravity: 1.140 @ 20掳C
Vapour Pressure: (mmHg): .01 @ 20掳C Solubility in Water: Negligible (<0.1%)
Boiling Point: n/a Freezing/Melting Point: -12掳C (10掳F)
Viscosity: 400 cps @ 20掳C Vapour Density (AIR=1): >1.0
Evaporation Rate: n/a % Volatile: <1.0 @ 20掳C
PH: Not available Odour: Mild slightly sweetish odour
Appearance: Medium viscosity grey liquid.
SECTION 4 - TOXICOLOGICAL PROPERTIES
NATURE OF HAZARD
INHALATION: Not a health hazard under conditions of normal use and temperature. Resin is not volatile at ambient
temperature of application.
EYE CONTACT: May irritate eyes. No permanent damage will result from contact.
/...2
MSDS-241
September 2006
SKIN CONTACT: This resin is a skin sensitizer. May cause initial irritation. Continuous and frequent contact could
lead to skin sensitization in certain individuals.
INGESTION: No information on health hazards of ingestion. Unlikely to cause any severe acute or chronic effects.
Low toxicity.
CHRONIC: No chronic effects known
OCCUPATIONAL EXPOSURE LIMIT: No TLV-TWA available (ACGIH).
SECTION 5 - FIRST AID MEASURES
INHALATION: Remove victim to fresh air. If adverse effects noticed see physician.
EYE CONTACT: Flush eyes with water for at least 15 minutes holding eyelids open. If irritation persists see
physician.
SKIN CONTACT: Flush with water. Use soap if available. Remove all contaminated clothing and fully launder
before reuse. If irritation persists see physician.
INGESTION: If swallowed, DO NOT INDUCE VOMITING! Seek immediate medical attention.
SECTION 6 - PREVENTIVE MEASURES
PERSONAL PROTECTION: The primary and only serious problem with handling the Base resin component of the
product is that of skin sensitization. However, the mixed product is a great deal more hazardous than the Base resin
component. Therefore, the minimum safety equipment and precautions will be identical to the Catalyst component of
this product. Wear safety glasses with side shields, full length PVC or neoprene gloves and full work coveralls as the
minimum protection.
ENGINEERING CONTROLS: Not necessary for indoor use where small quantities are used.
HANDLING, STORAGE AND SHIPPING: Keep containers closed when not in use. Handle and open containers
with care. Store under normal warehouse conditions. Empty product containers may contain product residue. DO
NOT REUSE!
SPILL CONTROL AND DISPOSAL: Soak up with absorbent inert material such as sand and collect in suitable
containers. Residual material may be removed with soap and hot water. For mixed product exercise care on disposal
of waste. Waste may be burned in an approved incinerator or buried at an approved land fill site. Observe all Federal,
Provincial and Municipal regulations in disposing of waste.
SECTION 7 - FIRE AND EXPLOSION DATA
Flashpoint and Method: 230掳F (110掳C) Seta Flash
Auto ignition Temperature: Not available
Flammable Limits: Not available
GENERAL HAZARDS: This product will burn under the right conditions of sufficient oxygen and heat. Toxic gases
will form upon combustion.
FIRE FIGHTING: Full protective gear including SCBA (Self-Contained Breathing Apparatus). Use carbon dioxide,
dry chemical or water spray.
HAZARDOUS COMBUSTION PRODUCTS: Phenol compounds, carbon dioxide, carbon monoxide.
/...3
MSDS-241
September 2006
SECTION 8 - REACTIVITY DATA
GENERAL: This product is stable and hazardous polymerization will not occur under normal conditions.
INCOMPATIBLE MATERIALS AND CONDITIONS TO AVOID: Strong oxidizing agent, amines, excessive heat,
strong bases and acids, water.
HAZARDOUS DECOMPOSITION: None.
SECTION 9 - PREPARATION
Prepared By: R.J. Green
Plant Manager
CPD Construction Products
Concord, Ontario, L4K 1L4
|