MSDS-30
September 2006
MATERIAL SAFETY DATA SHEET
CPD CLEAR RESIN BASE CONCRETE CURING COMPOUND (SOLVENT BASE)
SECTION 1 - PRODUCT INFORMATION
Manufacturer: CPD Construction Products
219 Connie Crescent # 13
Concord, Ontario L4K 1L4
Product Identifier: CPD Clear Resin Base Concrete Curing Compound. (Solvent Base)
Application & Use: Concrete Curing Compound. To be spray applied or applied by roller or brush.
Product Description: Hydrocarbon Resin Polymer dissolved in largely Aliphatic Hydrocarbon Solvent.
Regulatory Classification:
WHMIS - Class B Division 3 combustible Liquid.
Transportation of Dangerous Goods - Not regulated.
EMERGENCY NUMBERS
CANUTEC: (613) 996-6666
SECTION 2 - HAZARDOUS INGREDIENTS
The following component data is defined in accordance with sub-paragraph 13(a)(i) to (iv) or paragraph 14(a) of
the Hazardous Product Act.
NAME (pbw)% CAS
Aliphatic Hydrocarbon Solvent 75.0".5 64742-47-8
LD50(Oral Rat) >8000 mg./kg.
LC50(Rat) 1,400 ppm/4 Hours
SECTION 3 - PHYSICAL DATA
Physical State: Liquid Vapour Density (AIR=1): 4.9
Specific Gravity: .830 @ 20掳C Evaporation Rate: 0.11 (n-butylacetate=1)
Vapour Pressure: 7 mmHg. @ 38掳C % Volatile: 75.0 " .5%
Solubility in Water: <0.1% @ 20掳C Odour: Aliphatic Solvent (Mineral Spirits)
Boiling Point: 157-198掳C Appearance: Amber colour clear low viscosity liquid.
Viscosity: 5 cps @ 20掳C
SECTION 4 - TOXICOLOGICAL PROPERTIES
NATURE OF HAZARD
INHALATION: The vapours have a low to moderate toxicity. In high concentrations the vapours are irritating
and anaesthetic. The irritating properties give warning as anaesthetic concentrations are approached. However, a
similar type of solvent has produced kidney damage in experimental animals. To date no chronic effects have
been reported in man.
EYE CONTACT: Slightly irritating, but does not cause eye tissue damage.
SKIN CONTACT: Very low order of toxicity by skin absorption. However, frequent or prolonged contact may
irritate the skin and cause Defatting Dermatitis.
/...2
MSDS-30
September 2006
INGESTION: Low order of toxicity. However, minute amounts aspirated into the lungs during swallowing or
subsequent vomiting may cause severe lung irritation.
CHRONIC: Laboratory animal studies have shown that prolonged and repeated inhalation exposure to light
hydrocarbon vapours in the same naphtha boiling range as this product can produce adverse kidney effects in
male rats. However, these effects were not observed in similar studies with female rats and male and female mice
and in limited studies with other animal species. Additionally, in a number of human studies, there was no clinical
evidence of such effects at normal occupational levels. It is therefore highly unlikely that the kidney effects
observed in male rats have significant implications for humans exposed at or below recommended vapour limits
in the workplace.
OCCUPATIONAL EXPOSURE LIMIT: For vapour mixture: 100 ppm (575 mg/cu.m) total hydrocarbons
recommended.
Notes to Physician: If aspirated into lungs, Hydrocarbon Solvents may cause Chemical Pneumonitis. Cardiac
Arrythmias have been reported with solvent exposure.
SECTION 5 - FIRST AID MEASURES
INHALATION: Rescuers should wear respiratory protection. Remove immediately from contaminated area.
Apply artificial respiration if breathing has stopped. Call a physician.
EYE CONTACT: Flush with large amounts of water for at least 15 minutes holding eyelids open, seek medical
attention if irritation persists.
SKIN CONTACT: Wash with large amounts of soap and water. Remove contaminated clothing including shoes.
INGESTION: Due to the possibility of aspiration into the lungs, do not induce vomiting, keep at rest and call a
physician.
SECTION 6 - PREVENTIVE MEASURES
PERSONAL PROTECTION: Wear safety glasses with side shields, long sleeves, and chemical resistant gloves
(PVC, Neoprene Gloves). Where engineering, work practice or other means of exposure reduction are not
adequate, approved respirators may be necessary to prevent overexposure by inhalation.
ENGINEERING CONTROLS: Not necessary when product is applied outdoors or indoor application where
small quantities are used. For indoor applications involving the use of large quantities of product provide good
passive ventilation or explosion proof power ventilation.
HANDLING, STORAGE AND SHIPPING: Adequate ventilation should be provided to maintain the total
hydrocarbon concentration below the above mentioned occupational exposure limit. Avoid frequent or prolonged
skin contact. Wear suitable eye protection if the possibility of splashing exists. Keep container closed when not in
use. Do not store product near fire exits, open flames, sources of heat or sources of ignition. Post "NO
SMOKING" signs in areas of application. Product is a static accumulator. Take precautions as to adequate
grounding etc., when transferring at temperatures near or above flash point. Containers of this material may be
hazardous when emptied. Emptied containers retain product residue (vapour, liquid etc.). Do not allow this
product to freeze, store above 0掳C.
/...3
MSDS-30
September 2006
SPILL CONTROL AND DISPOSAL:
LAND SPILL - Eliminate source of ignition. Keep public away. Prevent spill from entering sewers, watercourses
or low areas. Contain spilled liquid with sand or earth. Do not use combustible materials such as sawdust.
Recover by using a suitable absorbent. Ensure disposal is in compliance with government requirements and
ensure conformity to local disposal regulations.
WATER SPILL: Remove from surface by skimming or with suitable absorbents. If allowed by local authorities
and environmental agencies, sinking and/or suitable dispersants may be used in non-confined waters. Ensure
disposal in compliance with government requirements and ensure conformity to local disposal regulations.
SECTION 7 - FIRE AND EXPLOSION DATA
Flash Point and Method: TCC: 42掳C (107掳F).
Auto Ignition Temperature: 229掳C (444掳F)
Flammable Limits (Percent by Volume) (Lel) 1.1 (Uel) 6.0
GENERAL HAZARDS: Combustible Liquid, may release vapours that form flammable mixtures at or above the
flash point. Toxic gases will form upon combustion.
FIRE FIGHTING: Use water spray to cool fire exposed surfaces and to protect personnel. Use foam, dry
chemical or water spray to extinguish fire. Respiratory and eye protection required for fire fighting personnel. A
self-contained breathing apparatus (SCBA) should be used for all indoor fires and any significant outdoor fires.
For small outdoor fires, which can easily be extinguished with a portable fire extinguisher, use of an SCBA may
not be required.
HAZARDOUS COMBUSTION PRODUCTS: Fumes, smoke and carbon monoxide.
SECTION 8 - REACTIVITY DATA
Stability: Stable
Materials/Conditions to Avoid: Strong oxidizing agents.
Hazardous Polymerization: Will not occur.
Hazardous Decomposition: None.
SECTION 9 - PREPARATION
Prepared By: R.J. Green
Plant Manager
CPD Construction Products
Concord, Ontario L4K 1L4
|