Concrete & Hard Surface Care
Aquathane
HP
For Use On:
Terrazzo Quarry Tile Concrete
Flagstone Brick
DESCRIPTION
A high performance premium quality acrylic membrane coating for sealing
High Performance
and finishing non-resilient hard surfaces, such as concrete, terrazzo,
granite, brick, un-glazed ceramic tile, slate or other stone surfaces. This
waterbased coating should be used where demand for excellent adhesion,
Hard Surface chemical resistance, and wear is required. Fast drying with no solvent
fumes makes this an ideal product for use in closed areas. This product
Seal/Finish
should be used for interior applications only.
Manufacturer鈥檚 Recommendation: This coating is to be applied
without thinning.
VOC Content = 73.2 grams/liter, excluding water
DIRECTIONS
SEALING AND FINISHING CONCRETE, TERRAZZO, QUARRY
TILE, FLAGSTONE, BRICK, UN-GLAZED CERAMIC TILE, and other
non-resilient surfaces.
PREPARATION: Remove all grease, oil, and other foreign material by
scrubbing with a heavy-duty cleaner and good scrub brushes. For better
adhesion on permanent type coatings such as moisture-cured urethanes
or epoxies, it is recommended that the surface be abraded with a
100-mesh screen disk. Smooth dense concrete surfaces should be acid
conditioned before application. Rinse floor thoroughly with clear water and
allow to dry.
APPLICATION: Apply a liberal coat using a mop, squeegee, roller, lambs
wool applicator or other appropriate applicator. If higher gloss is desired
apply a second coat after allowing first coat to dry approximately 45
minutes. Surface temperature should be above 40掳F. Allow final coat to dry
at least 8 hours before allowing heavy traffic onto floor.
PRODUCT SPECIFICATIONS
Chemical Resistance: Excellent
Non-volatile solids: 20.0卤0.5%
Leveling: Excellent
Color: Milky white
Sediment: 0.1% by volume, max.
Odor: Mild
Recoat Time: 45 minutes
Type: Waterborne urethane
Storage/Stability: 2 years
and acrylic polymers
Freeze/Thaw Stability: Keep from freezing
pH: 7.5 - 8.0
Weight per Gallon: 8.43 lbs./gal.
Specular Gloss: Greater than 90
Coverage: 1st coa t- 800-1000 ft2 per gal.
Slip Resistance: Greater than 0.50
2nd coat - 1000-1500 ft2 per gal.
Removability: With instant or solvent
VOC Content: 73.2 grams/liter
type strippers
Wear Resistance: Excellent
Misco Products Corporation 鈥? Reading, PA 鈥? (800) 548-4568 FAX (610) 926-1194
www.miscoprod.com
AQH MATERIAL SAFETY DATA SHEET N/A=Not Applicable
Prepared by: Regulatory Affairs Dept. Effective Date: 5/99 Revision: 10/99
(Prepared According to 29 CFR 1910.1200)
SECTION 1-PRODUCT IDENTIFICATION AND SUPPLIER INFORMATION
Manufacturer's Name: Product Name: Aquathane HP
Misco Products Corporation Generic Name: Hard Surface Seal & Finish
Manufacturer's Address: Chemical Family: Acrylic Blend
1048 Stinson Drive Reading, PA 19605 Formula: Proprietary
Manufacturer's Phone #: (610) 926-4106
SECTION 2-INGREDIENT INFORMATION
CHEMICAL NAME CAS NO. WT. % PEL TWA-TLV STEL-TLV
Water 7732-18-5 to 100
Acrylic Copolymer Dispersion N/A 40 to 45
Ethylene Glycol Monobutyl Ether 111-76-2 0 to 5 25ppm 25ppm 25ppm
Diethylene Glycol Methyl Ether 111-77-3 0 to 5
Dibutyl Phthalate 84-74-2 0 to 5
Tributoxyethyl Phosphate 78-51-3 0 to 5
SECTION 3-PHYSICAL DATA SECTION 4-FIRE AND EXPLOSION HAZARD DATA
Flash Point (Method Used): N/A
Boiling Point (掳F): 212 F. Specific Gravity: 1.01
Upper Explosion Limit: N/A Lower Explosion Limit: N/A
Vapor Pressure: 20mm Hg @ 68 F. Vapor Density (Air=1): >1
Extinguishing Media: N/A
% Volatile: 80+ pH: 7.5-8.0
Special Firefighting Procedures: Non Flammable
Solubility in Water: Complete Evaporation Rate (Water=1): <1
Unusual Fire and Explosion Hazards: N/A
Physical Description: Thin milky liquid with characteristic odor.
VOC Content (Subpart D 脽59.406) : 73.2 g/l
SECTION 5-REACTIVITY DATA
Stability: Stable Hazardous Polymerization: None
Hazards Decomposition Products: Will not occur Incompatibility (Materials to Avoid): None
SECTION 6-STORAGE AND HANDLING INFORMATION
Keep out of reach of children. For use by trained personnel only. Keep unauthorized personnel away when applying to floor. Keep container closed during storage. For
institutional and industrial use only. Avoid contact with eyes, skin and clothing. Avoid breathing of vapors. Use in well-ventilated area.
SECTION 7-HEALTH HAZARDS AND FIRST AID SECTION 8-SPECIAL PROTECTION INFORMATION
Effects of Overexposure: Respiratory Protection: Organic vapor canister respirator when in confined areas.
Skin: Prolonged or repeated contact may cause dermatitis. Ventilation Requirements: Provide local exhaust to keep TLV of Section 2 in-
gredients below acceptable limit.
Eyes: Eye irritant. May cause redness or swelling.
Protective Gloves: Chemical resistant rubber.
Inhalation: Vapors may be irritating to nose, throat, and lungs. May cause dizziness,
headache, and nausea. Eye Protection: Chemical splash goggles where danger of splash.
Ingestion: May be irritating to the mouth, throat, and gastrointestinal system. Vomiting Other Protective Equipment: Eyewash should be available. Protective footwear (e.g.
and diarrhea expected with large doses. rubber boots) when applying to floors.
First Aid Procedures: SECTION 9-SPILL OR LEAK PROCEDURES
Skin: Flush with water. Seek medical attention if irritation persists. Steps to be taken in Case Material is Released or Spilled: Floors will become
slippery. Avoid walking in product. Keep unessential personnel away. Mop up or
Eyes: Flush with large quantities of water, holding eyelids open. Seek medical
otherwise absorb and hold disposal. Avoid discharge to sewer or open waterways.
attention.
Waste Disposal Method: Any method in accordance with local, state and federal laws.
Inhalation: Remove victim to fresh air and monitor.
Best method is to recycle or reuse for intended purpose. Consult local authorities for
Ingestion: Dilute with 2 glasses of water. Seek medical attention if symptoms persist.
disposal in public sewer. Do not dispose of into storm drain, stream, river or to
ground. Rinse container thoroughly before discarding in trash.
SECTION 10-REGULATORY INFORMATION
HMIS Hazardous Materials
SARA Title III - Section 311/312 -Hazard Categories: Shipping Information:
No - Fire Hazard FOR CONTAINERS > 1 Gallon : Liquid Floor Wax Identification System
No - Sudden Release of Pressure Hazard Health 1
No - Reactivity Hazard FOR 1 GALLON CONTAINERS : Liquid Floor Wax Flammability 0
Yes - Immediate (acute) Health Hazard Reactivity 0
No - Delayed (chronic) Health Hazard FOR CONTAINERS < 1 GALLON : Liquid Floor Wax Personal Protection A
FOR EMERGENCY MEDICAL OR TRANSPORT INFORMATION: CHEM-TEL, Inc. @ 800-255-3924 (24 hours, 7 days per week)
This product contains the following toxic chemical(s) subject to the reporting requirements of section 313 of the Emergency Planning and Community Right-To-Know Act of 1986
and of 40 CFR 372.
CAS# Chemical Name Percent by Weight
None
This product contains the following chemical(s) which have been established to be either a carcinogen or suspected carcinogen.
CAS# Chemical Name Percent by Weight
None
SECTION 11-OTHER INFORMATION
This company cannot anticipate all conditions of handling and use of this product. Therefore, this company accepts no responsibility for results obtained by the application of this
information, or the safety and suitability of our products either alone or in combination with other products. It is the responsibility of the user to provide a safe workplace, using
the health and safety information contained herein as a guide. This company will accept no liability for damages or loss incurred from the improper handling and use of this
product
|