MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 2500
MSDS Number: 1019 Revision Date: 4/7/2008
1 of 6
Page
1 PRODUCT AND COMPANY IDENTIFICATION
Manufacturer
UNITEX
3101 Gardner Ave.
Kansas City, MO 64120
Contact: Technical Services
Telephone Number: 816-231-7700
FAX Number: 816-483-3149
E-Mail: mail@unitex-chemicals.com
Web www.unitex-chemicals.com
Product Name: PRO-POXY 2500
Revision Date: 4/7/2008
MSDS Number: 1019
Common Name: Aminopropyldiethanolamine
Product Code: PRO-POXY 2500
Chemical Family: Aminopropyldiethanolamine
Synonyms: Amines Liquid Corrosive
Product Use: Epoxy Patching Mortar
Emergency Telephone No.: CHEMTREC 800-424-9300
MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 2500
MSDS Number: 1019 Revision Date: 4/7/2008
2 of 6
Page
2 HAZARDS IDENTIFICATION
Route of Entry: Eyes, Skin, Swallowing, Inhalation.
Target Organs: None Known
Inhalation: May cause irritation to the nose and throat.
Skin Contact: May cause irritation and dermatitus.
Eye Contact: May cause irritation, sensitization and lead to eye damage.
Ingestion: May cause irritation of the mouth, stomach and sensitization.
HMIS II-ratings (scale 0-4): Health = 3, Fire = 1, Reactivity = 1
HMIS III-ratings (scale 0-4): Health = 3, Fire = 1, Physical Hazard = 1
NFPA-ratings (scale 0-4): Health = 3, Fire = 1, Reactivity = 1
Cured epoxy resins are innocuous.
COMPONENT C (Crystalline Silica):
INHALATION (Acute): Breathing dust may cause nose, throat or lung irritation and choking. The described effect depends on the degree of
exposure.
INHALATION (Chronic): Prolonged or repeated exposure may cause lung injury including silicosis. Crystalline silica has been classified by IARC as
a known human carcinogen. Some human studies indicate potential for lung cancer from crystalline silica exposure. Risk of injury depends on
duration and level of exposure. Long term exposure which results in silicosis may result in additional health effects.
OSHA PEL ACGIH TLV
COMPONENT A
25068386 NE NE
68609972 NE NE
98555 NE NE
COMPONENT B
694837 NE NE
68411905 NE NE
84852153 NE NE
NE NE NE
90722 10 mg/m3 5 mg/m3
14808607 10 mg/m3 .05 mg/m3
MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 2500
MSDS Number: 1019 Revision Date: 4/7/2008
3 of 6
Page
3 COMPOSITION/INFORMATION ON INGREDIENTS
Ingredients:
Cas # Chemical Name Perc.
----------------------------------------------------------------
COMPONENT A
Base Eopxy Resin
25068386 | Modified Bisphenol A | >80%
68609972 | Aliphatic Glycidyl Ether | 15%
98555 | Terpene Alcohol | <5%
COMPONENT B
Trade Secret Amine Blend containing one or more of the following:
694837 | | >90%
68411905 | |
84852153 | |
NE | |
90722 | 2,4,6-Tridimetylaminometyl)phenol | <10%
COMPONENT C
Trade secret Blend of Fillers
14808607 | Crystlline Silica | 100%
4 FIRST AID MEASURES
Inhalation: If respiratory irritation occurs, go to fresh air. Flood work area with fresh air. If irritation continues
seek medical attention.
Skin Contact: Remove contaminated clothing and shoes. Wash affected area(s) thoroughly with soap and water.
If irritation persists, seek medical attention. SOLVENTS SHOULD NOT BE USED because they
carry the irritant into the skin.
Eye Contact: Flush the eyes with plenty of water for at least 15 minutes. If necessary, gently hold eyelids open
during the flush. Immediately seek medical attention.
Ingestion: Obtain immediate medical attention. Do not induce vomiting. Should vomiting occur, be sure to
keep victim's head below hips to avoid aspiration of vomitus into the lungs.
5 FIRE FIGHTING MEASURES
Flash Point: >200F
Flash Point Method: Pensky Martins Closed Cup Method
Burning Rate: No data available
Autoignition Temperature: No data available
LEL: NA
UEL: NA
Special Fire Fighting Procedures: None. Avoid breathing smoke. NFPA Class B-C extinguisher (dry chemical or foam) for
class 1C fires. Water spray may be ineffective on fire but can protect fire-fighters and cool closed containers. Use fog nozzles
if water is used. Use supplied breathing masks
MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 2500
MSDS Number: 1019 Revision Date: 4/7/2008
4 of 6
Page
6 ACCIDENTAL RELEASE MEASURES
SMALL SPILL: Absorb with an inert material (sand, vermiculite, etc.). Sweep or scoop up and put into disposal containers. Flush area immediately
with soap and water (prevent water from entering waterways).
LARGE SPILL:
Containment: For large spills, dike far ahead of liquid spill for later disposal. Do not release into sewers or waterways.
Clean-up: Absorb with an inert material (sand, vermiculite, etc.). Sweep or scoop up into disposal containers. Flush area immediately with water
(prevent water from entering waterways).
Regulatory Requirements: Follow applicable OSHA regulations (29 CFR 1910.120).
Eliminate all ignition sources (flares, flames including pilot lights, electrical sparks). Persons not wearing protective equipment should be excluded
from area or until spill clean-up has been completed.
7 HANDLING AND STORAGE
Handling Precautions: For professional use only. Avoid eye/skin contact. Wash after using and before eating or
smoking. Avoid breathing vapors. Use as directed. Avoid uncontrolled mixing with other
mixtures (strong acids, bases and oxidizers). Respiratory protection is required when
ventilation is inadequate. NIOSH/OHSA approved respirators should be provided and
worn.
Storage Requirements: Store in a cool/dry location. Do not allow material to freeze, as product may be damaged.
Store away from sparks and open flames.
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Controls:
Protective Equipment: HMIS PP, H | Splash Goggles, Gloves, Apron, Vapor Respirator
VENTILATION: Provide general or local exhaust ventilation systems to maintain
airborne concentrations below OSHA PELs. Local exhaust ventilation is preferred
because it prevents contaminant dispersion into the work area by controlling it at its
source.
RESPIRATORY PROTECTION: Seek professional advice prior to respirator selection
and use. Follow OSHA respirator regulations (29 CFR 1910.134) and, if necessary,
wear OSHA/NIOSH approved respirator. Select respirator based on its suitability to
provide adequate worker protection for given working conditions, level of airborne
contamination, and presence of sufficient oxygen.
PROTECTIVE CLOTHING/EQUIPMENT: Wear chemically protective gloves, boots,
aprons to prevent prolonged or repeated skin contact. Wear protective goggles and
face shield, per OSHA eye and face protection regulation (29 CFR 1910.133).
CONTAMINATED EQUIPMENT: Separate contaminated work clothes from street
clothes. Launder before reuse. Remove this material from your work shoes and clean
personal protective equipment.
OTHER PRECAUTIONS: Never eat, drink, or smoke in work areas.
MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 2500
MSDS Number: 1019 Revision Date: 4/7/2008
5 of 6
Page
9 PHYSICAL AND CHEMICAL PROPERTIES
Appearance: A-Clear B-Amber C-White
Physical State: A/B= Liquid C=Solid Powder Boiling Point: ND
Odor: A=Mild B=Distnictive Freezing/Melting Pt.: ND/NE
C=None
pH: ND Solubility: Insoluble
Vapor Pressure: N/E Spec Grav./Density:
Vapor Density: (Air=1) >1
VOC: 0
Evap. Rate: Slower than Butyl Acetate
Viscosity: (A and B) Gel when mixed
Percent Volatile: 0
10 STABILITY AND REACTIVITY
Stability: Stable
Conditions to avoid: None
Materials to avoid (incompatability): Strong oxidizers, acids and bases.
Hazardous Decomposition products: CO, CO2, NOX
Hazardous Polymerization: None
11 TOXICOLOGICAL INFORMATION
No data available.
12 ECOLOGICAL INFORMATION
No data available.
13 DISPOSAL CONSIDERATIONS
When disposed of properly, this material does not meet RCRA classification or listing for hazardous waste. Never dispose of a
liquid to a landfill. Spilled material should be stablized or solidified prior to disposal. Once stabilized/solidified, the material
may be disposed of through normal means. Certain localities and state laws have specific disposal requirements for
non-hazardous industrial chemcials. Consult municipal authorities, landfill personnel, disposal companies for details prior to
any disposal activity. Always follow local, state and federal regulations.
14 TRANSPORT INFORMATION
DOT Class: Corrosive (8) #8
Shipping Name: Amines Liquid Corrosive, N.O.S. (aminopropyldiethanolamine) UN2735, Class 8
Corrosive, PGIII.
MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 2500
MSDS Number: 1019 Revision Date: 4/7/2008
6 of 6
Page
15 REGULATORY INFORMATION
This MSDS has been prepared in accordance with federal OSHA Hazard Communication Standard 29
CFR 1910.1200.
WHMIS Codes: Health(3) Flammability(1) Reactivity(1) PPE(H)
16 OTHER INFORMATION
The information and recommendations in this document are based on the best information available to us at the time of preparation. We make no
other warranty, expressed of implied, as to its correctness, or as to the results or reliance of this product.
This product has been classified according to the hazard criteria of the CPR and the MSDS contains all the information required by the CPR.
END OF MSDS DOCUMENT
|