MSDS Material Safety Data Sheet
UNITEX
QUICK SET 20 1 4
Page of
MSDS Number: 4009 Revision Date: 6/22/2007
1 PRODUCT AND COMPANY IDENTIFICATION
Manufacturer
UNITEX
3101 Gardner Ave.
Kansas City, MO 64120
Contact: Technical Services
Telephone Number: 816-231-7700
FAX Number: 816-483-3149
E-Mail: mail@unitex-chemicals.com
Web www.unitex-chemicals.com
Supplier Emergancy contacts & Phone
Contact #1 800-555-4545
Contact #2
Product Name: QUICK SET 20
Revision Date: 6/22/2007
MSDS Number: 4009
Product Code: QUICK SET 20
EMERGENCY TELEPHONE No.: 800-424-9300 CHEMTREC 24 hrs.
2 COMPOSITION/INFORMATION ON INGREDIENTS
Ingredients:
Cas # Chemical Name Perc.
----------------------------------------------------------------
65997151 | Portland cement | 30-60%
14808607 | Crystalline Silica | 30-60%
7631869 | Silica, amorphous | 0-5%
MSDS Material Safety Data Sheet
UNITEX
QUICK SET 20 2 4
Page of
MSDS Number: 4009 Revision Date: 6/22/2007
3 HAZARDS IDENTIFICATION
Route of Entry: Inhalation
Target Organs: None Known
Inhalation: Repeated inhalation of respirable dust over extended periods of time may cause injury to the lungs
(silicosis).
Skin Contact: May cause sensitisation by skin contact.
Eye Contact: May cause burning and corneal edema.
Ingestion: May cause caustic burns in the mouth, esophagus and stomach.
This product contains detectable amounts of chemicals known to the state of California to cause birth defects/cancer or other reproductive harm:
Crystalline Silica (SiO2).
Portland Cement
CAS No.: 65997151 OSHA PEL / 10 mg/m3
ACGIH TLV / 10 mg/m3
OTHER LIMITS / 50 MPPCF
Crystalline Silica
CAS No.: 14808607 OSHA PEL / 10 mg/m3
ACGIH TLV / 0.1 mg/m3
OTHER LIMITS / NA
Silica Amorphous
CAS No.: 7631869 OSHA PEL / NA
ACGIH TLV / NA
OTHER LIMITS / NA
SIGNS AND SYMPTOMS OF EXPOSURE: Cough, dyspnea (breathing difficulty), wheezing, decreased pulmonary function, progressive respiratory
symptoms (siliosis), irritation of eyes and potential occupational carcinogen.
4 FIRST AID MEASURES
Inhalation: Move to fresh air. If cough, irritation, or difficulty in breathing persist or develops, call a physician.
Skin Contact: Do not rub skin. Rinse skin free of material with water to avoid abrasion of skin. Wash thoroughly with soap
and water. SOLVENTS SHOULD NOT BE USED because they carry the irritant into the skin.
Eye Contact: Flush eyes with large amounts of water until subsides. If necessary gently hold open eyelids during the
flush. If irritation persists, get medical attention.
Ingestion: May cause caustic burns and tissue damage. Administer milk or water. Do not induce vomiting. Call a
physician or Poison Control Center immediately. Do not give anything orally to an unconscious person.
5 FIRE FIGHTING MEASURES
Flash Point: Non-Flammable
Flash Point Method: Tag closed cup
LEL: NA
UEL: NA
Flammability Classificati Non-Flammable
Other:
None
MSDS Material Safety Data Sheet
UNITEX
QUICK SET 20 3 4
Page of
MSDS Number: 4009 Revision Date: 6/22/2007
6 ACCIDENTAL RELEASE MEASURES
Steps to be taken in case material is released or spilled. No hazard. Vacuum or sweep up and dispose of in standard landfill. Avoid excessive
dusting.
Waste Disposal Method: Preferred procedure is to vacuum material. Otherwise, spray with water and clean up with broom and shovel. Dispose of in
accordance with local, state and federal regulations.
7 HANDLING AND STORAGE
Handling Precautions: Avoid dusting and prolonged contact between skin surfaces and wet or moist Portland Cement.
Storage Requirements: Store material on pallets in a dry location.
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Controls: The use of local exhaust ventilation is recomended to control emissions near the source. Provide
mechanical ventilation in confined spaces.
Protective Equipment: Immediately remove contaminated clothing. Wash hands before eating or drinking and practice
good hygien. Avoid contact with eyes and skin.
PROTECTIVE CLOTHING/EQUIPMENT: Wear impermeable gloves based on suitability to
protect from contact. Wear protective goggles, per OSHA eye and face protection regulations (29
CFR 1910.133).
RESPIRATORY PROTECTION: Seek professional advice prior to respirator selection and use.
Follow OSHA respirator regulations (29 CFR 1910.134) and, if necessary, wear OSHA/NIOSH
approved respirator. Select respirator based on its suitability to provide adequate worker
protection for given working conditions, level of airborne contamination, and presence of sufficient
oxygen.
9 PHYSICAL AND CHEMICAL PROPERTIES
Appearance: White
Physical State: Solid Powder Boiling Point: NA
Odor: None Freezing/Melting Pt.: NA
pH: NA Solubility: Negligible
Vapor Pressure: NA Spec Grav./Density: (H2O=1) 2.2
Vapor Density: (Air=1) NA
Percent Volatile: O g/l
MSDS Material Safety Data Sheet
UNITEX
QUICK SET 20 4 4
Page of
MSDS Number: 4009 Revision Date: 6/22/2007
10 STABILITY AND REACTIVITY
Stability: Stable
Conditions to avoid: None
Materials to avoid (incompatability): None
Hazardous Decomposition products: None
Hazardous Polymerization: Will not occur.
11 TOXICOLOGICAL INFORMATION
No data available. See Sections 3 and 15.
12 ECOLOGICAL INFORMATION
No data available.
13 DISPOSAL CONSIDERATIONS
Dispose of in accordance with local, state and federal regulations.
14 TRANSPORT INFORMATION
Not regulated by D.O.T.
15 REGULATORY INFORMATION
CHRONIC EFFECTS: Component Crystalline Silica. The International Agency for Research on
Cancer (IARC) has evaluated Crystalline Silica (group 1), and classified it as a possible
human carcinogen based on suficient evidence from cancer in exposed humans.
The National Toxicology Program (NTP) has listed Crystalline Silica as a group 2 carcinogen
and by the state of California (Proposition 65) as carcinogenic to humans.
16 OTHER INFORMATION
The information and recommendations in the document are based on the best information available to us at the time of preparation. We make no
other warranty, expressed or implied, as to the correctness or completeness, or as to the results or reliance of this product.
END OF MSDS DOCUMENT
|