MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 300 PASTE 1 5
Page of
MSDS Number: 1015 Revision Date: 2/14/2006
1 PRODUCT AND COMPANY IDENTIFICATION
Manufacturer
UNITEX
3101 Gardner Ave.
Kansas City, MO 64120
Contact: Technical Services
Telephone Number: 816-231-7700
FAX Number: 816-483-3149
E-Mail: mail@unitex-chemicals.com
Web www.unitex-chemicals.com
Supplier Emergancy contacts & Phone
Contact #1 800-555-4545
Contact #2
Product Name: PRO-POXY 300 PASTE
Revision Date: 2/14/2006
MSDS Number: 1015
Common Name: Aminopropyldiethanolamine
Product Code: PRO-POXY 300 PASTE
Chemical Family: Aminopropldiethanolamine
Synonyms: Amines Liquid Corrosive
Product Use: Structural Paste Adhesive
CHEMTREC Emergency Telephone No.: 800-424-9300
2 COMPOSITION/INFORMATION ON INGREDIENTS
Ingredients:
Cas # Chemical Name Perc.
----------------------------------------------------------------
COMPONENT A
25068386 | Modified Epoxy Resin | >60%
14807966 | Talc | <15%
1317653 | Coated Precipitated Calcium Carbonate | <15%
1314132 | Zinc Oxide | <15%
COMPONENT B
Trade Secret Amine Blend one or more of the following:
694837 | | <50%
143237 | |
140318 | |
100516 | |
NE | |
90722 | 2,4,6-Tri(dimethylainomethyl)phenol | <5%
14807966 | Talc | <20%
1317653 | Coated Precipitated Calcuim Carbonate | >20%
MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 300 PASTE 2 5
Page of
MSDS Number: 1015 Revision Date: 2/14/2006
3 HAZARDS IDENTIFICATION
Route of Entry: Eyes, Skin, Swallowing, Inhalation
Target Organs: None known
Inhalation: May cause irritation to nose and throat.
Skin Contact: May cause irritation and dermatitis.
Eye Contact: May cause irritation, sensitization and may lead to eye damage.
Ingestion: May cause irritation of the mouth, stomach and sensitization.
OSHA PEL ACGUH TLV
COMPONENT A
25068386 NE NA
14807966 5 mg/m3 5 mg/m3
1317653 5 mg/m3 10 mg/m3
1314132 5 mg/m3 5 mg/m3
COMPONENT B
694837 NE NE
143237 NE NE
140318 NE NE
100516 NE NE
NE NE NE
90722 10 mg/m3 5 mg/m3
14807966 5 mg/m3 5 mg/m3
1317653 10 mg/m3 5 mg/m3
None of the remaining components is considered a hazardous material or carcinogen (1910.1200 Hazard Communication (d) 4).
4 FIRST AID MEASURES
Inhalation: If respiratory irritation occurs, go to fresh air. Flood work area with fresh air. If Irritation continues seek
medical attention.
Skin Contact: Remove contaminated clothing and shoes. Wash affected area(s) thoroughly with soap and water. If
irritation persists, seek medical attention. SOLVENTS SHOULD NOT BE USED because they carry the
irritant into the skin.
Eye Contact: Flush the eyes with plenty of water for at least 15 minutes. If necessary, gently hold eyelids open during the
flush. Immediately seek medical attention.
Ingestion: Obtain immediate medical attention. Do not induce vomiting. Should vomiting occur, be sure to keep victim's
head below hips to avoid aspiration of vomitus into the lungs.
5 FIRE FIGHTING MEASURES
Flash Point: >200F
Flash Point Method: Pensky Martens Closed Cup Method
Burning Rate: No data available
Autoignition Temperature: No data available
LEL: NA
UEL: NA
Other:
Special Fire Fighting Procedures: None. Avoid breathing smoke. NFPA Class B-C extinguisher
(dry chemical or foam) for class 1C fires. Water spray may be ineffective on fire but can
protect fire-fighters and cool closed containers. Use fog nozzels if water is used. Use
supplied breathing masks.
MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 300 PASTE 3 5
Page of
MSDS Number: 1015 Revision Date: 2/14/2006
6 ACCIDENTAL RELEASE MEASURES
SMALL SPILLS: Absorb with an inert material (sand, vermiculite, etc.). Sweep or scoop up and put into disposal containers. Flush area immediately
with water (prevent water from entering waterways).
LARGE SPILLS:
Containment: For large spills, dike far ahead of liquid spill for later disposal. Do not release into sewers or waterways.
Clean-up: Absorb with an inert material (sand, vermiculite, etc.). Sweep or scoop up into disposal containers. Flush area immediately with water
(prevent water from entering waterways).
Regulatory Requirements: Follow applicable OSHA regulations (29 CFR 1910.120).
Eliminate all ignition sources (flares, flames including pilot lights, electrical sparks). Persons not wearing protective equipment should be excluded
from area or until clean-up has been completed.
7 HANDLING AND STORAGE
Handling Precautions: For professional use only. Avoid eye/skin contact. Wash after using and before eating or
smoking. Avoid breathing vapors. Use as directed. Avoid uncontrolled mixing with other
mixtures (strong acids, bases and oxidizers). Respiratory protection is required when
ventilation is inadequate. NIOSH/OSHA approved respirators should be provided and worn.
Storage Requirements: Store in a cool/dry location. Do not allow material to freeze, as product may be damaged. Store
away from sparks and open flames.
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Controls:
Protective Equipment: VENTILATION: Provide general or local exhaust ventilation systems to maintain airborne
concentrations below OSHA PELs. Local exhaust ventilation is preferred because it prevents
contaminant dispersion into the work area by controlling it at its source.
RESPIRATORY PROTECTION: Seek professional advice prior to respirator selection and use.
Follow OSHA respirator regulations (29 CFR 1910.134) and, if necessary, wear OSHA/NIOSH
approved respirator. Select respirator based on its suitablity to provise adequate worker protection
for given working conditions, level of airborne contamination, and presence of sufficient oxygen.
PROTECTIVE CLOTHING/EQUIPMENT: Wear chemically protective gloves, boots, aprons to
prevent prolonged or repeated skin contact. Wear protective goggles and face shield, per OSHA
eye and face protection regulations (29 CFR 1910.133).
CONTAMINATED EQUIPMENT: Separate contaminated work clothes from street clothes.
Launder before reuse. Remove this material from your work shoes and clean personal protective
equipment.
OTHER PRECAUTIONS: Never eat, drink or smoke in work areas.
This material is not listed by the International Agency for Research on Cancer, the National
Toxicology Program, or the Occupational Safety and Health Administration.
MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 300 PASTE 4 5
Page of
MSDS Number: 1015 Revision Date: 2/14/2006
9 PHYSICAL AND CHEMICAL PROPERTIES
Appearance: A-White B-Gray
Physical State: Gel Liquid Boiling Point: ND
Odor: A=Mild B=Strong Distinctive Freezing/Melting Pt.: ND/NE
pH: ND Solubility: Insoluble
Vapor Pressure: NE Spec Grav./Density:
Vapor Density: (Air=1) >1
VOC: 0
Evap. Rate: Slower than Butyl Acetate
Viscosity: Gel Paste
Percent Volatile: 0
CURED EPOXY RESINS ARE INNOCUOUS.
10 STABILITY AND REACTIVITY
Stability: Stable
Conditions to avoid: Fires during curing process.
Materials to avoid (incompatability): Strong oxidizers, acids and bases.
Hazardous Decomposition products: CO, CO2, NOX
Hazardous Polymerization: None
11 TOXICOLOGICAL INFORMATION
No data available.
12 ECOLOGICAL INFORMATION
No data available.
13 DISPOSAL CONSIDERATIONS
When disposed of properly, this material does not meet RCRA classification or listing for hazardous waste. Never dispose of a
liquid to a landfill. Spilled material should be stabilized or solidified prior to disposal. Once stabilized/solidified, the material
may be disposed of through normal means. Certain localities and state laws have specific disposal requirements for
non-hazardous industrial chemicals. Consult municipal authorites, landfill personnel, disposal companies for details prior to
any disposal activity. Always follow local, state and federal regulations.
14 TRANSPORT INFORMATION
Shipping Name: Amines Liquid Corrosive, N.O.S. (aminopropyldiethanolamine) UN2735, Class 8
Corrosive, PGIII.
Placards required over 1000 lbs.
MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 300 PASTE 5 5
Page of
MSDS Number: 1015 Revision Date: 2/14/2006
15 REGULATORY INFORMATION
This MSDS has been prepared in accordance with federal OSHA Hazard Communication Standard 29
CFR 1910.1200.
HMIS Codes: Health(3) Flammability(1) Reactivity(1) PPE(H)
16 OTHER INFORMATION
The information and recommendations in this document are based on the best information available to us at the time of preparation. We make no
other warranty, expressed or implied, as to its correctness or completeness, or as to the results or reliance of this product.
This product has been classified according to the hazard criteria of the CPR and the MSDS contains all the information required by the CPR.
END OF MSDS DOCUMENT
|