MSDS Material Safety Data Sheet
UNITEX
SLOW SET BONDING AGENT 1 4
Page of
MSDS Number: 1012 Revision Date: NOV 20, 2003
1 PRODUCT AND COMPANY IDENTIFICATION
Manufacturer
UNITEX
3101 Gardner Ave.
Kansas City, MO 64120
Contact: Technical Services
Telephone Number: 816-231-7700
FAX Number: 816-483-3149
E-Mail: mail@unitex-chemicals.com
Web www.unitex-chemicals.com
Product Name: SLOW SET BONDING AGENT
Revision Date: NOV 20, 2003
MSDS Number: 1012
Common Name: Aminopropyldiethanolamine
Product Code: SLOW SET BONDING AGENT
Chemical Family: Aminopropyldiethanolamine
Synonyms: Amines Liquid Corrosive
Product Use: Injection Resin
Emergency Telephone No:. 800-424-9300
MSDS Prepared by: Wm. Michael Simmons Director of Safety Phone: 816-231-7700
2 COMPOSITION/INFORMATION ON INGREDIENTS
Ingredients:
Cas # Chemical Name Perc.
----------------------------------------------------------------
Component A
Base Epoxy Resin
25068386 | Modified Bisohenol A/Epichlorohydrin | >90%
1317802 | TiO2 | <5%
1317653 | Coated Precipitated Calcium Carbonate | <5%
Component B
Trade Secret Amine Blend containing one or more of the following:
NE | | 100%
111400 | |
3 HAZARDS IDENTIFICATION
Route of Entry: Eyes, Skin, Swallowing, Inhalation
Target Organs: None Known
Inhalation: May cause irritation to nose and throat.
Skin Contact: May cause irritation and dermatitis.
Eye Contact: May cause irritation, sensitization and may lead to eye damage.
Ingestion: May cause irritation of the mouth, stomach and sensitization.
MSDS Material Safety Data Sheet
UNITEX
SLOW SET BONDING AGENT 2 4
Page of
MSDS Number: 1012 Revision Date: NOV 20, 2003
This product contains detectable amounts of a chemical known to the state of California to cause birth defects/cancer or other
reproductive harm: Epichlorohydrin.
OSHA PEL ACGUH TLV
COMPONENT A
25068386 NE NE
1317802 15 mg/m3 10 mg/m3
1317653 5 mg/m3 5 mg/m3
COMPONENT B
NE NE NE
111400 NE NE
None of the remaining components are considered a hazardous material or carcinogen (1910.1200 Hazard Communication
(d) 4).
4 FIRST AID MEASURES
Inhalation: If respiratory irritation occurs, go to fresh air. Flood work area with fresh air. If irritation continues seek
medical attention.
Skin Contact: Remove contaminated clothing and shoes. Wash affected area(s) thoroughly with soap and water. If
irritation persists, seek medical attention. SOLVENTS SHOULD NOT BE USED because they carry the
material into the skin.
Eye Contact: Flush the eyes with plenty of water for at least 15 minutes. If necessary, gently hold eyelids open during the
flush. Immediately seek medical attention.
Ingestion: Obtain immediate medical attention. Do not induce vomiting. Should vomiting occur, be sure to keep victim's
head below hips to avoid aspiration of vomitus into the lungs.
5 FIRE FIGHTING MEASURES
Flash Point: >200 F.
Flash Point Method: Pensky Martins Closed Cup Method
Burning Rate: No data available.
Autoignition Temperature: No data available.
LEL: NA
UEL: NA
Other:
Special Fire Fighting Procedures: None. Avoid breathing smoke. NFPA Class B-C extinguishers (dry chemical or foam) for
class 1C fires. Water spray may be ineffective on fire but can protect fire-fighters and cool closed containers. Use fog nozzels
if water is used. Use supplied breathing masks.
6 ACCIDENTAL RELEASE MEASURES
SMALL SPILLS: Absorb with an inert material (sand, vermiculite, etc.). Sweep or scoop and put into disposal containers.
Flush area immediately with water (prevent water from entering waterways).
LARGE SPILLS:
Containment: For large spills, dike far ahead of liquid spill for later disposal. Do not release into sewers or waterways.
Clean-up: Absorb with an inert material (sand, vermiculite, etc.). Sweep or scoop into disposal containers. Flush area
immediately with water (prevent water from entering waterways).
Regulatory Requirements: Follow applicable OSHA regulations (29 CFR 1910.120).
MSDS Material Safety Data Sheet
UNITEX
SLOW SET BONDING AGENT 3 4
Page of
MSDS Number: 1012 Revision Date: NOV 20, 2003
Eliminate all ignition sources (flares, flames including pilot lights, electrical sparks). Persons not wearing protective equipment
should be excluded from area or until spill clean-up has been completed.
7 HANDLING AND STORAGE
Handling Precautions: For professional use only. Avoid eye/skin contact. Wash after using and before eating or
smoking. Avoid breathing vapors. Use as directed. Avoid uncontrolled mixing with other
mixtures (strong acids, bases and oxidizers). Respiratory protection is required when
ventilation is inadequate. NIOSH/OSHA approved respirators should be provided and worn.
Storage Requirements: Store in a cool/dry location. Do not allow material to freeze, as product may be damaged. Store
away from sparks and open flames.
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Controls:
Protective Equipment: VENTILATION: Provide general or local exhaust ventilation systems to maintain airborne
concentrations below OSHA PELs. Local exhaust ventilation is preferred because it prevents
containment dispersion into the work area by controlling it at its source.
RESPIRATORY PROTECTION: Seek professional advice prior to respirator selection and use.
Follow OSHA respirator regulations (29 CFR 190.134) and, if necessary, wear OSHA/NIOSH
approved respirator. Select respirator based on its suitability to provide adequate worker
protection for given working conditions, level of airborne contamination, and presence of sufficient
oxygen.
PROTECTIVE CLOTHING/EQUIPMENT: Wear chemically protective gloves, boots, aprons to
prevent prolonged or repeated skin contact. Wear protective goggles and face shield, per OSHA
eye and face protection regulations (29 CFR 1910.133).
CONTAMINATED EQUIPMENT: Separate contaminated work clothes from street clothes.
Launder before reuse. Remove this material from your work shoes and clean personal protective
equipment.
OTHER PRECAUTIONS: Never eat, drink, or smoke in work areas.
This material is not listed by the International Agency for Research on Cancer, the National Toxocology Program, or the
Occupational Safety and Health Administration.
9 PHYSICAL AND CHEMICAL PROPERTIES
Appearance: A-Gray B-Amber
Physical State: Liquid Boiling Point: ND
Odor: A=Mild B=Strong Distinctive Freezing/Melting Pt.: ND/NE
pH: ND Solubility: Insoluble
Vapor Pressure: N/E Spec Grav./Density: A=1.14 B=1.01
Vapor Density: (Air=1) >1
VOC: 0
Evap. Rate: Slower than Butyl Acetate
Viscosity: Gel
Percent Volatile: 0
MSDS Material Safety Data Sheet
UNITEX
SLOW SET BONDING AGENT 4 4
Page of
MSDS Number: 1012 Revision Date: NOV 20, 2003
10 STABILITY AND REACTIVITY
Stability: Stable / Cured epoxy resins are innocuous.
Conditions to avoid: None
Materials to avoid (incompatability): Strong oxidizers, acids and bases
Hazardous Decomposition products: CO, CO2, NOX
Hazardous Polymerization: None
11 TOXICOLOGICAL INFORMATION
No data available.
12 ECOLOGICAL INFORMATION
No data available.
13 DISPOSAL CONSIDERATIONS
When disposed of properly, this material does not meet RCRA classification or listing for hazardous waste. Never dispose of a
liquid into a landfill. Spilled material should be stabilized or solidified prior to disposal. Once stabilized/solidified, the material
may be disposed of through normal means. Certain localities and state laws have specific disposal requirements for
non-hazardous industrial chemicals. Consult municipal authorites, landfill personnel, disposal companies for details prior to
any disposal activity. Always follow local, state and federal regulations.
14 TRANSPORT INFORMATION
Shipping Name: Amines, Liquid Corrosive, N.O.S. (aminopropyldiethanolamine) UN2735, Class 8 Corrosive, PGIII.
Placards required over 1000 lbs.
15 REGULATORY INFORMATION
This MSDS has been prepared in accordance with federal OSHA Hazard Communication Standard 29 CFR 1910.1200.
HMIS Codes: Health(3) Flammability(1) Rectivity(1) PPE(H)
16 OTHER INFORMATION
The information and recommedations in this document are based on the best information available to us at the time of
preparation. We make no other warranty, expressed or implied, as to its correctness or completeness, or as to the results or
reliance of this product.
This product has been classified according to the hazard criteria of the CPR and the MSDS contains all the information
required by the CPR.
END OF MSDS DOCUMENT
|