MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 50 SUPER LV-1 1 4
Page of
MSDS Number: 1022 Revision Date: NOV 20, 2003
1 PRODUCT AND COMPANY IDENTIFICATION
Manufacturer
UNITEX
3101 Gardner Ave.
Kansas City, MO 64120
Contact: Technical Services
Telephone Number: 816-231-7700
FAX Number: 816-483-3149
E-Mail: mail@unitex-chemicals.com
Web www.unitex-chemicals.com
Product Name: PRO-POXY 50 SUPER LV-1
Revision Date: NOV 20, 2003
MSDS Number: 1022
Common Name: Aminopropyldiethanolamine
Product Code: PRO-POXY 50 SUPER LV-1
Chemical Family: Aminopropyldiethanolamine
Synonyms: Amines Liquid Corrosive
Product Use: Low Viscosity Injection Resin
Emergency Telephone No:. 800-424-9300
MSDS Prepared by: Wm. Michael Simmons Director of Safety Phone: 816-231-7700
2 COMPOSITION/INFORMATION ON INGREDIENTS
Ingredients:
Cas # Chemical Name Perc.
----------------------------------------------------------------
Component A Base Epoxy Resin
25068386 | Modified Bisphenol A/Epichlorohydrin | >75%
2461156 | Aliphatic Glycidyl Ether | <25%
Component B
Trade Secret Amine Blend containing one or more of the following:
91203 | | >90%
84852153 | |
140318 | |
9046100 | |
NE | |
90722 | 2,4,6 Tri(dimethylaminomethyl)phenol | <8%
None of the remaining components are considered a hazardous material or carcinogen (1910.1200 Hazard Communication
(d) 4).
3 HAZARDS IDENTIFICATION
Route of Entry: Eyes, Skin, Swallowing, Inhalation
Target Organs: None Known
MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 50 SUPER LV-1 2 4
Page of
MSDS Number: 1022 Revision Date: NOV 20, 2003
Inhalation: May cause irritation to nose and throat.
Skin Contact: May cause irritation and dermatitis.
Eye Contact: May cause irritation, sensitization and may lead to eye damage.
Ingestion: May cause irritation of the mouth, stomach and sensitization.
This product contains detectable amounts of a chemical known to the state of California to cause birth defects/cancer or other
reproductive harm: Epichlorohydrin.
OSHA PEL ACGUH TLV
Component A
25068386 NE NA
2461156 NE NE
Component B
91203 NE NE
84852153 NE NE
140318 NE NE
9046100 NE NE
NE NE NE
90722 10 mg/m3 5 mg/m3
4 FIRST AID MEASURES
Inhalation: If respiratory irritation occurs, go to fresh air. Flood work area with fresh air. If irritation continues seek
medical attention.
Skin Contact: Remove contaminated clothing and shoes. Wash affected area(s) thoroughly with soap and water. If
irritation persists, seek medical attention. SOLVENTS SHOULD NOT BE USED because they carry the
irritant into the skin.
Eye Contact: Flush eyes with plenty of water for at least 15 minutes. If necessary, gently hold eyelids open during the
flush. Immediately seek medical attention.
Ingestion: Obtain immediate medical attention. Do not induce vomiting. Should vomiting occur, be sure to keep victim's
head below hips to avoid aspiration of vomitus into the lungs.
5 FIRE FIGHTING MEASURES
Flash Point: >200F
Flash Point Method: Pensky Martens Closed Cup Method
Burning Rate: No data available.
Autoignition Temperature: No data available.
LEL: NA
UEL: NA
Other:
Special Fire Fighting Procedures: None. Avoid breathing smoke. NFPA Class B-C extinguisher (dry chemical or foam) for
class 1C fires. Water spray may be ineffective on fire but can protect fire-fighters and cool closed containers. Use fog nozzels
if water is used. Use supplied air breathing masks.
6 ACCIDENTAL RELEASE MEASURES
SMALL SPILLS: Absorb with an inert material (sand, vermiculite, etc.). Sweep or scoop up into disposal containers. Flush
area immediately with water (prevent water form entering waterways).
LARGE SPILLS:
Containment: For large spills, dike far ahead of liquid spill for later disposal. Do not release into sewers or waterways.
MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 50 SUPER LV-1 3 4
Page of
MSDS Number: 1022 Revision Date: NOV 20, 2003
Clean-up: Absorb with an inert material (sand, vermiculite, etc.). Sweep or scoop up into disposal containers. Flush area
immediately with water (prevent water from entering waterways).
Regulatory Requirements: Follow applicable OSHA regulations (29 CFR 1910.120).
Eliminate all ignition sources (flares, flames including pilot lights, electrical sparks). Persons not wearing protective clothing
should be excluded from area or until clean-up has been completed.
7 HANDLING AND STORAGE
Handling Precautions: For professional use only. Avoid eye/skin contact. Wash after using and before eating or
smoking. Avoid breathing vapors. Use as directed. Avoid uncontrolled mixing with other
mixtures (strong acids, bases and oxidizers). Respirator protection is required when ventilation
is inadequate. NIOSH/OSHA approved respirators should be provided and worn.
Storage Requirements: Store in a cool/dry location. Do not allow material to freeze, as product may be damaged. Store
away from sparks and open flames.
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Controls:
Protective Equipment: VENTILATION: Provide general or local exhaust ventilation systems to maintain airborne
concentrations below OSHA PELs. Local exhaust ventilation is preferred because it prevents
containment dispersion into the work area controlling it at its source.
RESPIRATORY PROTECTION: Seek professional advice prior to respirator selection and use.
Follow OSHA respirator regulations (29 CFR 1910.134) and if necessary, wear OSHA/NIOSH
approved respirator. Select respirator based on its suitablity to provide adequate worker protection
for given working conditions, level of airborne contamination, and presence of sufficient oxygen.
PROTECTIVE CLOTHING/EQUIPMENT: Wear chemically protective gloves, boots, aprons to
prevent prolonged or repeated skin contact. Wear protective goggles and face shield, per OSHA
eye and face protection regulations (29 CFR 1910.133).
CONTAMINATED EQUIPMENT: Separate contaminated work clothes from street clothes.
Launder before reuse. Remove this material from your work shoes and clean personal protective
equipment.
This material is not listed by the International Agency for Research on Cancer, the National
Toxicology Program, or the Occupational Safety and Health Administration.
9 PHYSICAL AND CHEMICAL PROPERTIES
Appearance: A-Clear B-Amber
Physical State: Liquid Boiling Point: ND
Odor: A=Mild B=Strong Distinctive Freezing/Melting Pt.: ND/NE
pH: ND Solubility: Insoluble
Vapor Pressure: N/E Spec Grav./Density: A=1.10 B=0.96
Vapor Density: (Air=1) >1
VOC: 0
Evap. Rate: Slower than Butly Acetate
Viscosity: Brookfield 175 cps
Percent Volatile: 0
MSDS Material Safety Data Sheet
UNITEX
PRO-POXY 50 SUPER LV-1 4 4
Page of
MSDS Number: 1022 Revision Date: NOV 20, 2003
10 STABILITY AND REACTIVITY
Stability: Stable
Conditions to avoid: None
Materials to avoid (incompatability): Strong oxidizers, acids and bases.
Hazardous Decomposition products: CO, CO2, NOX
Hazardous Polymerization: None
11 TOXICOLOGICAL INFORMATION
No data available.
12 ECOLOGICAL INFORMATION
No data available.
13 DISPOSAL CONSIDERATIONS
When disposed of properly, this material does not meet RCRA classification or listing for hazardous waste. Never dispose of a
liquid to a landfill. Spilled material should be stabilized or solidified prior to disposal. Once stabilized/solidified, the material
may be disposed of through normal means. Certain localities and state laws have specific disposal requirements for
non-hazardous industrial chemicals. Consult municipal authorites, landfill personnel, disposal companies for details prior to
any disposal activity. Always follow local, state and federal regulations.
14 TRANSPORT INFORMATION
Shipping Name: Amines, Liquid Corrosive, N.O.S. (amoinopropyldiethanolamine) UN2735, Class 8 Corrosive, PGIII
Placards required over 1000 lbs.
15 REGULATORY INFORMATION
This MSDS has been prepared in accordance with federal OSHA Hazard Communication Standard 29 CFR 1910.1200.
HMIS Codes: Health(3) Flammability(1) Reactivity(1) PPE(H)
16 OTHER INFORMATION
The information and recommendations in this document are based on the best information available to us at the time of
preparation. We make no other warranty, expressed or implied, as to its correctness or completeness, or as to the results or
reliance of this product.
This product has been classified according to the hazard criteria of the CPR and the MSDS contains all the information
required by the CPR.
END OF MSDS DOCUMENT
|