MSDS Material Safety Data Sheet
UNITEX
UNI CURE 1 4
Page of
MSDS Number: 2007 Revision Date: Jan 10, 2004
1 PRODUCT AND COMPANY IDENTIFICATION
Manufacturer
UNITEX
3101 Gardner Ave.
Kansas City, MO 64120
Contact: Technical Services
Telephone Number: 816-231-7700
FAX Number: 816-483-3149
E-Mail: mail@unitex-chemicals.com
Web www.unitex-chemicals.com
Product Name: UNI CURE
Revision Date: Jan 10, 2004
MSDS Number: 2007
Product Code: UNI CURE
Product Use: Chemical Hardener and densifier
EMERGENCY TELEPHONE No.: 800-424-9300 CHEMTREC 24 hrs.
MSDS Prepared by: Wm. Michael Simmons Director of Safety Phone No.: 800-821-5846
HMIS Codes: Health(1) Flammability(0) Reactivity(0) PPE(B)
2 COMPOSITION/INFORMATION ON INGREDIENTS
Not applicable; Non-hazardous aqueous solution, no warnings, no UN or NA number. None of the remaining compounds are
considered Hazardous Material by OSHA (29 CFR 1910.1200 Hazardous Communication (d) 4). or DOT.
3 HAZARDS IDENTIFICATION
Route of Entry: Eyes, Skin, Ingestion
Target Organs: None known.
Inhalation: May cause irritation.
Skin Contact: May cause irritation and dermatitis.
Eye Contact: May cause irritation.
Ingestion: May cause irritation of the mouth, stomach and cause sensitization.
4 FIRST AID MEASURES
Inhalation: If respiratory irritation occurs, go to fresh air. Flood work area with fresh air. If irritation continues seek
medical attention.
Skin Contact: Remove contaminated clothing and shoes. Wash affected area(s) thoroughly with soap and water. If
irritation persists, seek medical attention. SOLVENTS SHOULD NOT BE USED because they carry the
irritant into the skin.
Eye Contact: Flush the eyes with plenty of water for at least 15 minutes. If necessary, gently hold eyelids open during the
flush. Immediately seek medical attention.
Ingestion: Obtain immediate medical attention. Do not induce vomiting. Should vomiting occur, be sure to keep victim's
head below hips to avoid aspiration of vomitus into the lungs. Fluids should never be given to an
MSDS Material Safety Data Sheet
UNITEX
UNI CURE 2 4
Page of
MSDS Number: 2007 Revision Date: Jan 10, 2004
head below hips to avoid aspiration of vomitus into the lungs. Fluids should never be given to an
unconscious person.
5 FIRE FIGHTING MEASURES
Flash Point: Not applicable
Flammability Classificati Non flammable
Other:
Special fire fighting procedures: None. This material is water based. Use water spray to protect fire-fighters. If water is to be
used, use a fog nozzel to cool closed containers. Avoid spraying directly into open containers to prevent boilover.
6 ACCIDENTAL RELEASE MEASURES
SMALL SPILLS: Absorb with an inert material (sand, vermiculite, etc.). Sweep or scoop up into disposal containers. Flush
area immediately with water (prevent water from entering waterways).
LARGE SPILLS:
Containment: For large spills, dike far ahead of liquid spill for later disposal. Do not release into sewers or waterways.
Clean-up: Absorb with an inert material (sand, vermiculite, etc.). Sweep or scoop up into disposal containers. Flush area
immediately with water (prevent water from entering waterways).
Regulatory Requirements: Follow applicable OSHA regulations (29 CFR 1910.120).
Dissolve in large amounts of water and add soda ash. Neutralize with 6M-HCL. After neutralizattion, product can be disposed
of by normal means (landfill). Flush with large quantity of water.
7 HANDLING AND STORAGE
Handling Precautions: For professional use only. Avoid eye/skin contact. Wash after using and before eating or
drinking. Avoid breathing vapors. Use as directed.
Storage Requirements: Store in a cool/dry location. DO NOT ALLOW MATERIAL TO FREEZE, as product may be
damaged.
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Controls:
Protective Equipment: VENTILATION: Provide general or local exhaust ventilation systems to maintain clean air. Local
exhaust ventilation is preferred because it prevents contaminant dispersion into the work area by
controlling it at its source.
RESPIRATORY PROTECTION: Seek professional advice prior to respirator selection and use.
Follow OSHA respirator regulations (29 CFR 1910.134) and, if necessary wear OSHA/NIOSH
approved respirator. Select respirator based on its suitability to provide adequate worker
protection for given working conditions, level of airborne contamination, and presence of sufficient
oxygen.
PROTECTIVE CLOTHING/EQUIPMENT: Wear chemically protective gloves and goggles, per
OSHA eye and face protection regulations (29 CFR 1910.133).
CONTAMINATED EQUIPMENT: Separate contaminated work clothes from street clothes.
Launder before reuse. Remove this material from your work shoes and clean personal protective
equipment.
This material is not listed by the International Agency for Research on Cancer, the National Toxicology Program, or the
Occupational Safety and Health Administration.
MSDS Material Safety Data Sheet
UNITEX
UNI CURE 3 4
Page of
MSDS Number: 2007 Revision Date: Jan 10, 2004
9 PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Viscous, Colorless
Physical State: Liquid Boiling Point: 210 deg. F.
Odor: Odorless Freezing/Melting Pt.: 32 deg. F / ND
pH: Solubility: 100%
Vapor Pressure: 17.50 mm/Hg Spec Grav./Density: (H20=1) 1.4
Vapor Density: (Air=1) 0.6
VOC: 0
Percent Volatile: 0
10 STABILITY AND REACTIVITY
Stability: Stable
Conditions to avoid: None
Materials to avoid (incompatability): None known
Hazardous Decomposition products: None
Hazardous Polymerization: Will not occur.
11 TOXICOLOGICAL INFORMATION
No data available.
12 ECOLOGICAL INFORMATION
No data available.
13 DISPOSAL CONSIDERATIONS
After product is neutralized with 6M-HCL, deposit sludge in a landfill.
14 TRANSPORT INFORMATION
Not regulated by Department of Transportation.
15 REGULATORY INFORMATION
Non regulated.
HMIS Codes: Health(1) Flammability(0) Reactivity(0) PPE(B)
16 OTHER INFORMATION
MSDS Material Safety Data Sheet
UNITEX
UNI CURE 4 4
Page of
MSDS Number: 2007 Revision Date: Jan 10, 2004
The information and recommendations in this document are based on the best information available to us at the time of
preparation. We make no other warranty, expressed or implied, as to its correctness or completeness, or as to the results or
reliance of this product.
This product has been classified according to the hazard criteria of the CPR and the MSDS contains all the information
required by the CPR.
END OF MSDS DOCUMENT
|