Material Name: Fabric PermaFlash Scrim Material Safety Data
Sheet ID: 3018
Section 1 - Chemical Product and Company Identification
Product Name Fabric PermaFlash Scrim
CAS# Not Assigned
Generic Name Polyester Fabric
Formula Polymer
Chemical Name: Polymer
Manufacturer Information
Johns Manville Telephone: 303-978-2000 8:00AM-5:00PM M-F
Roofing Systems Group Internet Address: http://www.jm.com
P.O. Box 5108 Emergency: 800-424-9300 (Chemtrec, In English)
Denver, CO 80127 USA
Trade Names: Fabric PermaFlash Scrim
Section 2 - Composition / Information on Ingredients
CAS # Component Percent
Not Available Polyethylene terephthalate polymer 100
Section 3 - Hazards Identification
Emergency Overview
APPEARANCE AND ODOR: Solid polyester stitch bonded and knit fabric. No odor.
This product is used with PermaFlash Primer found on JM MSDS ID 3017.
Potential Health Effects
Summary
With normal, intended use, this product is not expected to create any significant health effects or hazards.
Inhalation
During normal use of this product there is not expected to be an inhalation hazard.
Skin
Under normal conditions of use, this product is not expected to be a skin irritant.
Absorption
Not applicable.
Ingestion
Not expected to be an ingestion hazard.
Eyes
Under normal conditions of use, this product is not expected to be an eye irritant.
Primary Routes of Entry (Exposure)
Inhalation (breathing) and eyes when heating this material.
Target Organs
None identified.
Section 4 - First Aid Measures
First Aid: Inhalation
No special procedures necessary.
First Aid: Skin
Wash exposed skin with soap and water.
First Aid: Ingestion
Product is not intended to be ingested or eaten. If the material is swallowed, get immediate medical attention or advice -- Do
not induce vomiting.
____________________________________________________________
Page 1 of 4 Issue Date: 07/07/2005 Revision: 1.0000
Material Name: Fabric PermaFlash Scrim Material Safety Data
Sheet ID: 3018
First Aid: Eyes
If irritation develops, flush with water for 5-15 minutes. Should symptoms persist, seek medical attention.
First Aid: Notes to Physician
Provide general supportive measures and treat symptomatically.
Section 5 - Fire Fighting Measures
Flash Point: Not determined Method Used: Not determined
Upper Flammable Limit (UFL): Not determined Lower Flammable Limit (LFL): Not determined
Auto Ignition: Not determined Flammability Classification: Not determined
Rate of Burning: Not determined
General Fire Hazards
Polyesters can burn if exposed to flame. Molten polymer generates small amounts of volatile degradation products (off-gases),
one of which is acetaldehyde. Acetaldehyde vapors form explosive mixtures with air that can spontaneously ignite (auto-ignite)
at temperatures above 347掳 F (175掳C). There is no potential for spontaneous fire or explosion.
Hazardous Combustion Products
Upon decomposition, this product may emit carbon, hydrogen, and nitrogen.
Extinguishing Media
Water, dry chemical, foam
Fire Fighting Equipment/Instructions
No special procedures are expected to be necessary for this product. Normal fire fighting procedures should be followed to
avoid inhalation of smoke and gases.
Section 6 - Accidental Release Measures
Containment Procedures
No special procedures necessary
Clean-Up Procedures
Pick up or shovel material into waste container. If cannot be reused, place in covered container for disposal.
Section 7 - Handling and Storage
Handling Procedures
Wash thoroughly after handling.
Storage Procedures
Warehouse storage should be in accordance with package directions, if any. Material should be kept clean, dry, and protected
from moisture.
Section 8 - Exposure Controls / Personal Protection
Exposure Guidelines
A: General Product Information
No additional information available.
B: Component Exposure Limits
ACGIH, OSHA, and NIOSH have not developed exposure limits for any of this product's components.
PERSONAL PROTECTIVE EQUIPMENT
Personal Protective Equipment: Eyes/Face
Safety glasses are recommended.
Personal Protective Equipment: Skin
Normal work clothing (long sleeved shirts and long pants) is recommended. Wash thoroughly after use.
Personal Protective Equipment: Respiratory
No special procedures necessary. Use in well ventilated areas.
Ventilation
No special ventilation systems are required under normal conditions of use.
Personal Protective Equipment: General
Use good industrial hygiene practices when handling this material.
____________________________________________________________
Page 2 of 4 Issue Date: 07/07/2005 Revision: 1.0000
Material Name: Fabric PermaFlash Scrim Material Safety Data
Sheet ID: 3018
Section 9 - Physical & Chemical Properties
Appearance: Odor:
Solid polyester fabric. No odor
Physical State: pH:
Solid Not applicable
Vapor Pressure: Vapor Density:
Not applicable Not applicable
Boiling Point: Melting Point:
Not applicable Not applicable
Solubility (H2O): Specific Gravity:
Not applicable Not applicable
Freezing Point: Evaporation Rate:
Not applicable Not applicable
VOC: Not applicable
Section 10 - Chemical Stability & Reactivity Information
Chemical Stability
This is a stable material.
Chemical Stability: Conditions to Avoid
Avoid open flame.
Incompatibility
None identified.
Hazardous Decomposition
Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons.
Hazardous Polymerization
Will not occur.
Section 11 - Toxicological Information
Acute Toxicity
A: General Product Information
No additional information available.
B: Component Analysis - LD50/LC50
No LD50/LC50's are available for this product's components.
Carcinogenicity
A: General Product Information
No data for this product as a whole.
B: Component Carcinogenicity
None of this product's components are listed by ACGIH, IARC, OSHA, NIOSH, or NTP.
Chronic Toxicity
None identified.
Section 12 - Ecological Information
Ecotoxicity
A: General Product Information
No data available for this product.
B: Component Analysis - Ecotoxicity - Aquatic Toxicity
No ecotoxicity data are available for this product's components.
Section 13 - Disposal Considerations
US EPA Waste Number & Descriptions
A: General Product Information
This product, as supplied, is not regulated as a hazardous waste by the U.S. Environmental Protection Agency (EPA) under
Resource Conservation and Recovery Act (RCRA) regulations. Comply with state and local regulations for disposal. If you are
unsure of the regulations, contact your local Public Health Department, or the local office of the EPA.
B: Component Waste Numbers
No EPA Waste Numbers are applicable for this product's components.
Disposal Instructions
Dispose of waste material according to Local, State, Federal, and Provincial Environmental Regulations.
Section 14 - Transportation Information
This product is not regulated for transport.
____________________________________________________________
Page 3 of 4 Issue Date: 07/07/2005 Revision: 1.0000
Material Name: Fabric PermaFlash Scrim Material Safety Data
Sheet ID: 3018
Section 15 - Regulatory Information
US Federal Regulations
A: General Product Information
SARA 311/312: This product is not classified as hazardous under SARA 311/312.
B: Component Analysis
None of this products components are listed under SARA Section 302 (40 CFR 355 Appendix A), SARA Section 313 (40 CFR
372.65), or CERCLA (40 CFR 302.4).
State Regulations
A: General Product Information
Other state regulations may apply. Check individual state requirements.
B: Component Analysis - State
None of this product's components are listed on the state lists from CA, FL, MA, MN, NJ, or PA.
A: TSCA Status
This product and its components are listed on the TSCA 8(b) inventory.
None of the components listed in this product are listed on the TSCA Export Notification 12(b) list.
Component Analysis - WHMIS IDL
No components are listed in the WHMIS IDL.
Section 16 - Other Information
Other Information
Prepared for:
Johns Manville
Roofing Systems Group
P. O. Box 5108
Denver, CO USA 80217-5108
Prepared by:
Johns Manville Technical Center
P.O. Box 625005
Littleton, CO USA 80162-5005
The information herein is presented in good faith and believed to be accurate as of the effective date given. However, no
warranty, expressed or implied, is given. It is the buyer's responsibility to ensure that its activities comply with Federal, State or
provincial, and local laws.
Date MSDS # Reason
07/07/05 3018-1.0000 New product. New MSDS.
This is the end of MSDS # 3018
____________________________________________________________
Page 4 of 4 Issue Date: 07/07/2005 Revision: 1.0000
|