Material Name: JM EPDM Bonding Cement Material Safety Data
Sheet ID: 3141
Section 1 - Chemical Product and Company Identification
Product Name JM EPDM Bonding Cement (Water-Borne)
CAS# Mixture/None Assigned
Generic Name Adhesive (water-borne)
Formula Mixture
Chemical Name: Mixture
Hazard Label ML-5115
Manufacturer Information
Johns Manville Telephone: 303-978-2000 8:00AM-5:00PM M-F
Roofing Systems Group Internet Address: http://www.jm.com
P.O. Box 5108 Emergency: 800-424-9300 (Chemtrec, In English)
Denver, CO 80127 USA
Trade Names: JM EPDM Bonding Cement (Water-Borne)
Section 2 - Composition / Information on Ingredients
CAS # Component Percent
8052-41-3 Stoddard solvent (mineral spirits) 1-6
1314-13-2 Zinc oxide 1-6
Proprietary TSR#1397250002-5176P >3
Proprietary TSR#1397250002-5383P >3
Proprietary TSR#1397250002-5109P >3
Proprietary TSR#1397250002-5142P >3
7732-18-5 Water >3
1317-65-3 Calcium carbonate >3
Section 3 - Hazards Identification
Emergency Overview
APPEARANCE AND ODOR: Grey liquid.
Product and its vapors may be irritating to skin, eyes, and respiratory tract. May cause sensitization by skin contact.
HMIS Ratings: Health = 1 Fire = 0 Reactivity = 0
Potential Health Effects
Inhalation
Prolonged breathing of vapor or mist may result in mild respiratory tract irritation.
Skin
Prolonged contact may result in mild skin irritation.
Ingestion
Ingestion of this product is unlikely. However, ingestion of product may produce gastrointestinal irritation and disturbances.
Eyes
This product may cause irritation to the eyes.
Primary Routes of Entry (Exposure)
Skin contact, eye contact, inhalation, ingestion.
Target Organs
Upper respiratory passages, skin, and eyes.
Section 4 - First Aid Measures
First Aid: Inhalation
Remove to fresh air. If symptoms persist contact a physician.
____________________________________________________________
Page 1 of 5 Issue Date: 10/26/2006 Revision: 2.0102
Material Name: JM EPDM Bonding Cement Material Safety Data
Sheet ID: 3141
First Aid: Skin
Remove contaminated clothing. Wash exposed areas with soap and water. If irritation develops or persists, seek medical
attention. Launder contaminated clothing before reuse.
First Aid: Ingestion
Product is not intended to be ingested or eaten. If the material is swallowed, get immediate medical attention or advice -- Do
not induce vomiting.
First Aid: Eyes
Flush eyes with large amounts of water for 5-20 minutes. Contact a medical professional.
First Aid: Notes to Physician
Treatment for inhalation, skin contact, or ingestion should be symptomatic.
Section 5 - Fire Fighting Measures
Flash Point: None Method Used: Not applicable
Upper Flammable Limit (UFL): Not applicable Lower Flammable Limit (LFL): Not applicable
Auto Ignition: Not determined Flammability Classification: Not combustible
Rate of Burning: Not determined
General Fire Hazards
Not a fire hazard. Exposure of closed containers to temperatures above the boiling point could cause pressure buildup and
container rupture. Dry adhesive film will burn.
Hazardous Combustion Products
Combustion may yield carbon monoxide, carbon dioxide, and/or oxides of nitrogen.
Extinguishing Media
For dried solids, use water, foam, CO2, or dry chemical media.
Fire Fighting Equipment/Instructions
No special procedures are expected to be necessary for this product. Normal fire fighting procedures should be followed to
avoid inhalation of smoke and gases. Fire fighters should wear self-contained breathing apparatus (SCBA) in enclosed areas.
Section 6 - Accidental Release Measures
Containment Procedures
Dam, mop, absorb onto sawdust or other absorbent, and place in suitable container.
Clean-Up Procedures
Comply with state and local regulations for disposal of this product. If you are unsure of the regulations, contact your local
Public Health Department, or the local office of the Environmental Protection Agency (EPA).
Section 7 - Handling and Storage
Handling Procedures
Use protective equipment as described in Section 8 of this material safety data sheet when handling uncontained material.
Storage Procedures
Material should be kept cool and dry, and protected from moisture. Store in tightly closed containers to prevent contamination.
Section 8 - Exposure Controls / Personal Protection
Exposure Guidelines
A: General Product Information
Protective equipment should be provided as necessary to prevent irritation of the eyes, skin, and respiratory tract, and to keep
exposure levels below the applicable exposure limits.
B: Component Exposure Limits
Zinc oxide (1314-13-2)
ACGIH: 2 mg/m3 TWA (respirable fraction)
10 mg/m3 STEL (respirable fraction)
OSHA: 5 mg/m3 TWA (fume); 10 mg/m3 TWA (total dust); 5 mg/m3 TWA (respirable fraction)
10 mg/m3 STEL (fume)
Stoddard solvent (mineral spirits) (8052-41-3)
ACGIH: 100 ppm TWA
OSHA: 100 ppm TWA; 525 mg/m3 TWA
____________________________________________________________
Page 2 of 5 Issue Date: 10/26/2006 Revision: 2.0102
Material Name: JM EPDM Bonding Cement Material Safety Data
Sheet ID: 3141
Calcium carbonate (1317-65-3)
OSHA: 15 mg/m3 TWA (total dust); 5 mg/m3 TWA (respirable fraction)
PERSONAL PROTECTIVE EQUIPMENT
Personal Protective Equipment: Eyes/Face
Safety glasses with sideshields, chemical goggles, or face mask recommended.
Personal Protective Equipment: Skin
Wear impervious gloves for prolonged contact.
Personal Protective Equipment: Respiratory
If ventilation is inadequate to keep airborne dust (from dried product) vapors and fumes below exposure limits, use a NIOSH-
approved dust/organic vapor respirator.
Ventilation
Local exhaust or general dilution ventilation may be required to maintain exposures below the applicable exposure limits. The
need for ventilation systems should be evaluated by a professional industrial hygienist, while the design of specific ventilation
systems should be conducted by a professional engineer.
Personal Protective Equipment: General
No additional information available.
Section 9 - Physical & Chemical Properties
Appearance: Odor:
Grey Ammonia-type odor
Physical State: pH:
Liquid 8-11
Vapor Pressure: Vapor Density:
17.5 @ 20潞C <1
Boiling Point: Melting Point:
100潞C/212潞F Not applicable
Solubility (H2O): Specific Gravity:
Appreciable 1.079
Freezing Point: Evaporation Rate:
0潞C/32潞 F <1
Viscosity: Percent Volatile:
Not determined 48
VOC: 41 g/L
Section 10 - Chemical Stability & Reactivity Information
Chemical Stability
This is a stable material.
Chemical Stability: Conditions to Avoid
Freezing or boiling
Incompatibility
Any material that reacts violently with water, i.e., concentrated acids, calcium carbide, sodium.
Hazardous Decomposition
Carbon monoxide, carbon dioxide, and/or oxides of nitrogen.
Hazardous Polymerization
Will not occur.
Section 11 - Toxicological Information
Acute Toxicity
A: General Product Information
Vapor and mist may be irritating to eyes, skin, and respiratory tract. May cause sensitization by skin contact.
B: Component Analysis - LD50/LC50
Zinc oxide (1314-13-2)
Oral LD50 Rat: >5000 mg/kg
Water (7732-18-5)
Oral LD50 Rat: >90 mL/kg
Carcinogenicity
A: General Product Information
The Occupational Safety and Health Administration (OSHA), National Toxicology Program (NTP), International Agency for
Research on Cancer (IARC), and American Conference of Governmental Industrial Hygienists (ACGIH) have not classified
this product as a carcinogen.
____________________________________________________________
Page 3 of 5 Issue Date: 10/26/2006 Revision: 2.0102
Material Name: JM EPDM Bonding Cement Material Safety Data
Sheet ID: 3141
B: Component Carcinogenicity
None of this product's components are listed by ACGIH, IARC, OSHA, NIOSH, or NTP.
Chronic Toxicity
May cause skin sensitization in some individuals.
Section 12 - Ecological Information
Ecotoxicity
A: General Product Information
No additional information available.
B: Component Analysis - Ecotoxicity - Aquatic Toxicity
No ecotoxicity data are available for this product's components.
Environmental Fate
No information available for the product.
Section 13 - Disposal Considerations
US EPA Waste Number & Descriptions
A: General Product Information
Comply with state and local regulations for disposal. If you are unsure of the regulations, contact your local Public Health
Department, or the local office of the EPA.
B: Component Waste Numbers
No EPA Waste Numbers are applicable for this product's components.
Disposal Instructions
Dispose of waste material according to Local, State, Federal, and Provincial Environmental Regulations.
Section 14 - Transportation Information
Shipping Name: Not regulated as a hazardous material for transport.
Section 15 - Regulatory Information
US Federal Regulations
A: General Product Information
SARA 311/312: This product is not classified as hazardous under SARA 311/312.
B: Component Analysis
None of this products components are listed under SARA Section 302 (40 CFR 355 Appendix A), SARA Section 313 (40 CFR
372.65), or CERCLA (40 CFR 302.4).
State Regulations
A: General Product Information
Other state regulations may apply. Check individual state requirements.
B: Component Analysis - State
The following components appear on one or more of the following state hazardous substances lists:
Component CAS # CA FL MA MN NJ PA
Zinc oxide 1314-13-2 Yes No Yes Yes Yes Yes
Stoddard solvent (mineral spirits) 8052-41-3 Yes No Yes Yes Yes Yes
Calcium carbonate 1317-65-3 No No Yes Yes No Yes
A: TSCA Status
This product and its components are listed on the TSCA 8(b) inventory.
None of the components listed in this product are listed on the TSCA Export Notification 12(b) list.
____________________________________________________________
Page 4 of 5 Issue Date: 10/26/2006 Revision: 2.0102
Material Name: JM EPDM Bonding Cement Material Safety Data
Sheet ID: 3141
B: Component Analysis - Inventory
Component CAS # TSCA DSL EINECS
Zinc oxide 1314-13-2 Yes Yes Yes
Stoddard solvent (mineral spirits) 8052-41-3 Yes Yes Yes
Water 7732-18-5 Yes Yes Yes
Calcium carbonate 1317-65-3 Yes No Yes
Component Analysis - WHMIS IDL
The following components are identified under the Canadian Hazardous Products Act Ingredient Disclosure List:
Component CAS # Minimum Concentration
Zinc oxide 1314-13-2 1%
Stoddard solvent (mineral spirits) 8052-41-3 1%
Section 16 - Other Information
Other Information
Prepared for:
Johns Manville
Roofing Systems Group
P. O. Box 5108
Denver, CO USA 80217-5108
Prepared by:
Johns Manville Technical Center
P.O. Box 625005
Littleton, CO USA 80162-5005
The information herein is presented in good faith and believed to be accurate as of the effective date given. However, no
warranty, expressed or implied, is given. It is the buyer's responsibility to ensure that its activities comply with Federal, State or
provincial, and local laws.
Date MSDS # Reason
08/01/00 3141-1.0000 New MSDS authoring system.
09/03/03 3141-2.0000 New formulation.
07/20/05 3141-2.0001 Regulatory update: Sections 8, 11, 12
09/23/05 3141-2.0002 Section 2 Composition update; Edits throughout MSDS
10/25/06 3141-2.0102 Replaced UltraGard in product name with JM.
This is the end of MSDS # 3141
____________________________________________________________
Page 5 of 5 Issue Date: 10/26/2006 Revision: 2.0102
|