CPD庐 NON-SHRINK FIBER GROUT
(PRE-MIX)
DESCRIPTION APPLICATION
CPD庐 Non-Shrink Fiber Grout is a pre-blended, ready to SURFACE PREPARATION
All surfaces that will be in contact with the grout must be
use cement based grout containing non-ferrous, anti-
clean and free of grease, oil, standing water, laitance, loose
shrinkage compounds and reinforcing organic fibers
material or any other contaminant that could impair
blended with graded siliceous aggregate and Portland
substrate bond. Prior to grouting, foundation concrete
cement. This grout requires only the addition of water.
should be roughened, cleaned and thoroughly wetted down
for 12 hours. Free standing water should be blown clear
WHERE TO USE
CPD庐 Non-Shrink Fiber Grout (Pre-Mix) is used for just prior to grouting.
grouting stamping machines, large compressors, pulp and
paper dryers, rolling mills and applications involving MIXING AND PLACING
Use only as much water as is consistent with flowability
impact and stress.
required. Mix thoroughly and place within one hour. Keep
grout agitated in mixer at all times. As soon as grout sets,
BENEFITS
cure with CPD庐 Acrylic Cure & Seal, CPD庐 Clear Resin
鈥? good flowability
Based Curing Compound or wet cure. Ideal grouting
鈥? surface contact - its expansive nature facilitates
temperature is 10? (50掳F) to 25? (77?
C C F).
placement in confined and difficult areas thus ensuring
Cooler temperatures will slow the rate of strength gain.
complete bearing of machine bases
鈥? complete bearing surface contact ensures uniform load
Note : Do not exceed 4.0L water per 25 kg bag of grout
distribution
(1.06 U.S. gal/55 lb).
鈥? controlled expansion - factory blending of expansion
agents ensures uniform, consistent expansion for over
LIMITATIONS
one hour
鈥? CPD庐 Non-Shrink Fiber Grout should not be used
鈥? durability - CPD庐 Non-Shrink Fiber Grout exhibits
where service temperature will exceed 176? (350?
C F)
excellent freeze-thaw resistance even with flowable
or where contact is likely with strong acids or alkalies
consistencies
鈥? consult a CPD庐 Technical Representative when
temperatures are below 4.5掳C (40掳F) or above 32掳 C
PROPERTIES
(90掳F)
Compressive Strength
(ASTM C109-77) 21? (70掳F) C
flowable (150% Flow ASTM C230-28) 4L (1.06 U.S. YIELD
gal) water 0.014m鲁 (0.47 ft鲁) per 25 kg (55 lb) bag.
12 hours.....................................18.1 MPa (2,625 psi)
1 day..........................................32.6 MPa (4,725 psi) STANDARDS
CPD庐 Non- Shrink Fiber Grout is formulated to comply
3 days.........................................39.8 MPa (5,775 psi)
7 days.........................................50.7 MPa (7,350 psi) with U.S. Corps of Engineers CRD-C621-92, and ASTM
28 days.......................................61.6 MPa (8,925 psi) C1107-91.
Set Time:...................................6 hours @ 21掳C (70掳F) PACKAGING
25 kg.(55 lb) multi-wall bag.
The above information is representative of actual
production runs. Independent test results may vary from STORAGE
the above by approximately 卤 10%. May be stored short term anywhere under tarp on pallets
as long as the product is kept dry. Dry heated warehouse
storage is recommended for extended storage.
0360-02-1105
SHELF LIFE
One year from the date of manufacture when stored in
original, unopened package and under normal warehouse
conditions.
SAFETY PRECAUTION
Consult Material Safety Data Sheet (M.S.D.S.) for
specific instructions. MSDS #20
WARRANTY
The recommendations made and the information herein is
based on our own and independent laboratory experience,
and is believed to be accurate under controlled conditions.
However, no warranty or guarantee of accuracy is made
because we cannot cover every possible application of
product nor anticipate every variation encountered in
weather conditions, job-conditions, methods used and
types of surfaces on which the product is applied. The
users shall make their own tests to determine the suitability
of such products for any particular purpose.
CPD庐 makes no warranties with respect to this product,
expressed or implied, without limitation, the implied
warranties of merchantability or fitness for a particular
purpose.
CPD庐鈥? liability shall be limited in all events to supplying
s
sufficient product to re-treat and/or repair the specific area
to which CPD庐 product has been applied. CPD庐 reserves
the right to have the true cause of any difficulty determined
by accepted test methods. CPD庐 shall have no other
liability, including liability for incidental, consequential or
resultant damages, however caused, whether due to breach
of warranty, negligence, or strict liability.
THIS WARRANTY MAY NOT BE MODIFIED OR
EXTENDED BY REPRESENTATIVES OF CPD庐, ITS
DISTRIBUTORS OR DEALERS.
|