CIPADECK® Membrane 100
Polyurethane Waterproofing Membrane
DESCRIPTION Tensile Adhesion To Concrete . . 2.41Mpa (350 psi)
CIPADECK® Membrane 100 is a high performance
(ASTM D4541)
100% solids two component amine-cured polyurethane
Tear Strength . . . . . . . . . . . . . . 12KN/m (68.5 pli)
waterproofing membrane.
(ASTM 624)
Abrasion Resistance (ASTM D4060) . . 120 mg loss
WHERE TO USE
CIPADECK® Membrane 100 is used to provide a traffic Taber Abrasion, C-17 Wheel, 1000 cycles
bearing waterproof coating in mechanical rooms, Chloride Permeability . . . . . . . . . . . . .0 Coulombs
computer access floors, shower rooms and other areas (AASHTO T-2770)
requiring an effective waterproofing system. This
application will require a traffic bearing top coat of
The above information is representative of actual
CIPADOR® E-400 (no primer is necessary in mechanical
production runs. Independent test results may vary
room applications).
from the above by approximately ±10%.
BENEFITS
APPLICATION
� 100% solids, with no offensive odors, zero VOC� s
SURFACE PREPARATION
� retains its integrity even if substrate movement
New concrete must be cured for a minimum of 28 days
causes hairline cracks up to 1.6 mm (1/16")
before applying CIPADECK® Membrane 100. The
� applied in a one coat application of 20 to 40 mils
substrate must be above 10°C (50°F) and must be free
thickness
of all dirt, waxes, previously applied coatings, oil,
� contains no isocyanate or any other harmful materials
grease, laitance and any foreign matter that may
� good adhesion to concrete and steel
interfere with the bond of the coating to the substrate.
� ample working time with excellent handling
Cracks and surface defects should be repaired prior to
properties
application of the coating. All concrete and steel
� available in dark grey
surfaces to be coated should be shot blast, water blast
or mechanically cleaned to provide a clean tooth for the
Handling Properties
coating. Prime with CIPADITE® HI when the concrete
Mix Ratio, by volume . . . . . . . . . 2 parts A: 1 part B substrate is dry or CIPADITE® Primer DS when the
Viscosity(Mixed) @ 25°C (77°F) . . . . . . . . 3000 cps concrete is damp, prior to the application of the
CIPADECK® Membrane 100.
Solids Content . . . . . . . . . . . . . . . . . . . . . . . . . 100 %
Mixed Weight (Density) 1.065kg/litre (8.9 lb./US gal)
DETAILING
Pot Life @ 25°C (77°F) . . . . . . . . . . . . . . . . 4 hours
Joints or cracks should be repaired prior to application
Foot Traffic @ 25°C (77°F) . . . . . . . . . . . . 16 hours
of CIPADECK® Membrane 100. Cracks and cold
Vehicular Traffic @ 25°C (77°F) . . . . . . . . . . 3 days
joints less than 1.6mm (1/16") wide should be coated
Full Cure and Maximum Resistance . . . . . . . . 7 days over with the CIPADECK® Membrane 100. All
cracks and joints greater than 1.6mm (1/16") wide must
be routed and sealed with an approved polyurethane
DATA - Cured Film
sealant. The CIPADECK® Membrane 100 must be
Tensile Elongation . . . . . . . . . . . . . . 325 % @ break
extended a minimum distance of 50mm (2") on either
(ASTM D412)
side of all sealed cracks, cold joints and control joints
Tensile Strength . . . . . . . . . . . . . . 4.5 Mpa (650psi) to yield a total film thickness of 20-30 mils dry.
(ASTM D412)
Hardness (Shore A) . . . . . . . . . . . . . . . . . . . . . . . . 30
(ASTM D2240-86)
0960-22-1105
MIXING WARRANTY
The mixing equipment used to mix the coating must be The recommendations made and the information herein
clean and free of any contaminants that may be present in is based on our own and independent laboratory
the equipment from previously used products. Mix experience, and is believed to be accurate under
component A first to eliminate the possibility of controlled conditions. However, no warranty or
settlement. Pour all of the liquid from Part A and Part B guarantee of accuracy is made because we cannot cover
into the mixing equipment. A � Jiffy Mixer� or a mud every possible application of product nor anticipate
mixer blade on a slow speed drill is the preferred method every variation encountered in weather conditions, job
of mixing. Mix the blended components for a minimum conditions, methods used and types of surfaces on
of 2 minutes. which the product is applied. The users shall make their
own tests to determine the suitability of such products
for any particular purpose.
APPLICATION
Apply CIPADECK® Membrane 100 to an even thickness
CPD® makes no warranties with respect to this product,
using a squeegee and further level using a lint free 5mm
nap roller (designed for epoxy and urethane) to achieve a expressed or implied, including, without limitation, the
total thickness of 20 to 40 mils. Allow the membrane to implied warranties of merchantability or fitness for a
cure overnight before applying CIPADOR® E-400. particular purpose.
CPD®� liability shall be limited in all events to
s
LIMITATIONS
Do not apply CIPADECK® Membrane 100: supplying sufficient product to re-treat and/or repair the
specific area to which the CPD® product has been
� if the substrate and ambient temperatures are below
applied. CPD® reserves the right to have the true cause
10°C (50°F)
� do not apply to a damp surface of any difficulty determined by accepted test methods.
� prime with CIPADITE® Primer DS when the CPD® shall have no other liability, including liability
concrete substrate is damp. for incidental, consequential or resultant damages,
however caused, whether due to breach of warranty,
negligence, or strict liability.
COVERAGE
Based on 20 mils thickness per coat:
2 m²/litre (80 ft²/U.S. gallon) THIS WARRANTY MAY NOT BE MODIFIED OR
EXTENDED BY REPRESENTATIVES OF
CPD®,ITS DISTRIBUTORS OR DEALERS.
PACKAGING
CIPADECK® Membrane 100 is packaged in:
3.79 litre/1 U.S. gal. units
11.4 litre/3 U.S. gal. units
56.7 litre/15 U.S. gal. units
CLEAN UP
Clean all equipment and installation tools immediately
with CPD® Xylol . Read the M.S.D.S. for this product
prior to use.
STORAGE
Store in a heated warehouse. Do not freeze.
SHELF LIFE
Three years from the date of manufacture if kept in
original unopened containers under normal heated
warehouse conditions.
SAFETY PRECAUTIONS
Consult Material Safety Data Sheet (M.S.D.S.) for
specific instructions. M.S.D.S. #294 + 294A
|