CPD庐 CLOSED CELL FOAM JOINT FILLER
DESCRIPTION PACKAGING
CPD庐 Closed Cell Foam Joint Filler is a non-extruding CPD庐 Closed Cell Foam Joint Filler is supplied in the
PVC foam, suitable for moving joints usually found when following:
differences in the coefficient of expansion occur with Soft Grade: Sheets 48"x 64" (21.3ft虏)
different substrates. It comes in two grades, a soft grade Available in thickness: 7mm (0.27"), 13 mm (0.5"),
which exhibits a recovery over 90% and a rigid grade which 19mm (0.74"), 25 mm (0.98"), 38 mm (1.48") and
provides greater resistance to compression. 50mm (1.95")
Rigid Grade: Sheets 48"x 64" (21.3 ft虏)
Thickness: 7mm (0.27"), 13mm (0.5"), 19mm (0.74"),
WHERE TO USE
The soft grade is used in masonry block and brick 25 mm (0.98"), 38mm (1.48"), and 50 mm (1.95").
construction, expansion joints around curved surfaces,
isolation joints around columns and heavy machinery, and STORAGE
May be stored anywhere. Weather protection outside is
precast joints. The rigid grade is used in poured-in-place
desirable but not necessary.
concrete, retaining walls, bridges and adjoining structures.
SHELF LIFE
BENEFITS
Indefinite if kept protected under normal warehouse
鈥? resistant to most oils, chemicals and weather
conditions.
鈥? transmits little heat or moisture
鈥? non-toxic
SAFETY PRECAUTIONS
Consult Material Safety Data Sheet ( M.S.D.S.)
PROPERTIES
For specific instructions. MSDS # 236.
Soft Rigid
Grade (ASTM D1056) RE-41 Extra Firm
WARRANTY
Oil Resistance (ASTM D1056) E-2 E-2
The recommendations made and the information herein is
Density (ASTM D1667) lbs/ft鲁 4-6 4-6
based on our own laboratory experience, and is believed
Compression Deflection 2-5 20-30
to be accurate under controlled conditions. However, no
at 25% (ASTM D1056)
warranty or guarantee of accuracy is made because we
Compression Set at 50% 30% 70%
cannot cover every possible application of product nor
(ASTM D1056)
anticipate every variation encountered in weather
Elongation (ASTM D412) 75% 70%
conditions, job-conditions, methods used and types of
Tensile Strength (ASTM D412) 0.34MPa 0.68MPa
surfaces on which the product is applied. The users shall
(50 psi) (100 psi)
make their own tests to determine the suitability of such
Water Absorption (ASTM D105) 65% 5%
products for any particular purpose.
Flammability (UL-94AHF-1) passes passes
CPD庐 makes no warranties with respect to this product,
APPLICATION
Care should be taken in positioning CPD庐 Closed Cell expressed or implied, without limitation, the implied
warranties of merchantability or fitness for a particular
Foam Joint Filler so that it does not protrude above the
purpose.
surface. For best results a minimum of 13mm (陆") should
be provided from the surface of the concrete to the top of
CPD庐鈥? liability shall be limited in all events to supplying
s
the filler if a sealant is to be used to finish off the joint.
sufficient product to re-treat and/or repair the specific
area to which CPD庐 product has been applied. CPD庐
LIMITATIONS
CPD庐 Closed Cell Foam Joint Filler should not be reserves the right to have the true cause of any difficulty
determined by accepted test methods. CPD庐 shall have
subjected to continuous high pressure conditions. Not for
no other liability, including liability for incidental,
use with hot applied sealants.
0792-02-1105
consequential or resultant damages, however caused,
whether due to breach of warranty, negligence, or strict
liability.
THIS WARRANTY MAY NOT BE MODIFIED OR
EXTENDED BY REPRESENTATIVES OF CPD庐, ITS
DISTRIBUTORS OR DEALERS.
|