CIPADOME庐 Conductive
Conductive Epoxy Resin
DESCRIPTION Conductivity & Spark Proof Results
CIPADOME庐 CONDUCTIVE is a 100% solids black
Test Requirements Results
conductive epoxy gel. It is normally used as a light to
medium duty epoxy floor topping. It is a versatile resin 5.3.1 average 0.14M? Pass
that can be combined with graded crushed walnut shells Electrostatic resistance <1
Protection M?
to provide a spark proof flooring system, or combined
with colored marble or granite aggregate as a conductive
5.3.2.1 Electric average 0.14M? Pass
epoxy terrazzo or used by itself as a conductive Shock Protection resistance not
coating/sealer. CIPADOME庐 CONDUCTIVE is (dry) less than 25k?
designed with a conductivity of 200,000- 500,000 Ohms
5.3.2.2 Electric average 0.03M? Pass
resistance.
Shock Protection resistance not
(Wet) less than 25k?
BENEFITS
鈥? 100 % solids, with no offensive odors, zero VOC鈥? s 5.4 Mechanical no visible sparks no visible Pass
鈥? versatile conductive epoxy resin Spark Protection sparks
鈥? easy to apply
鈥? good chemical resistance to dilute acids, caustics APPLICATION
and common solvents SURFACE PREPARATION
New concrete must be cured for a minimum of 28 days
Handling Properties before applying CIPADOME庐 CONDUCTIVE. The
Resin & Hardener Only: substrate must be above 10掳C (50掳F) and must be free of
all dirt, waxes, previously applied coatings, oil, grease,
Mix Ratio, by volume . . . . . . . . 4 parts A : 1 part B
laitance and any foreign matter that may interfere with the
Solids: Content . . . . . . . . . . . . . . . . . . . . . . . 100%
bond of the topping to the prepared substrate. Cracks and
Mixed Weight (Density) ... 1.1kg/litre (9.4lb./US gal)
surface defects should be repaired prior to the application
Pot Life @ 23掳C (74掳F) A&B . . . . . . . . . 30 minutes
of the topping. All concrete surfaces to be treated should be
Mortar . . . . . . 60 minutes shot blast, water blast, or mechanically cleaned to provide
Initial Set @ 23? (74掳F) . . . . . . . . . . . . . . 8 hours
C a clean tooth for the topping application. If acid etching is
Foot Traffic @ 23? (74掳F) . . . . . . . . . . . 12 hours
C the method of choice for preparation of the concrete
surface, the etched surface must be thoroughly flushed,
Vehicular Traffic . . . . . . . . . . . . . . . . . . . 24 hours
neutralized and dry prior to the topping application.
Full Cure . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 days
PRIMING:
DATA - Cured Properties Substrates to receive CIPADOME庐 CONDUCTIVE must
Compressive Strength: . . . . . 90.0 Mpa (13,000 psi) have copper grounding rods in place prior to application.
The mixing equipment used to mix the topping must be
(ASTM C-579)
clean and free of any contaminants that may be present in
Flexural Strength . . . . . . . . . . 21.0 Mpa (3,000 psi)
the equipment from previously used products. Mix
(ASTM C-580)
component 鈥淎鈥? first to eliminate the possibility of
Abrasion Resistance: . . . . . . . . . . . . . . . . 86mg loss
settlement. Combine both Part 鈥淎鈥? and Part 鈥淏鈥? and mix
Taber Abrasion, C-17 Wheel, 1000 cycles well for one minute. Pour all of the mixed liquid into the
mixing container and slowly add the walnut shells and
continue mixing. It is imperative that the mixer be a slow
speed model to avoid damage and possible discoloration
of the matrix.
0960-17-1105
REFER TO CIPADOME庐 SPARK PROOF DATA the product is applied. The users shall make their own tests
SHEET FOR MORE DETAIL REGARDING THE to determine the suitability of such products for any
APPLICATION. particular purpose.
CPD 庐 makes no warranties with respect to this product,
LIMITATIONS
Do not apply CIPADOME庐 CONDUCTIVE if: expressed or implied including, without limitation, the
鈥? substrate or ambient temperatures are below 10?C implied warranties of merchantability or fitness for a
(50? F) particular purpose.
鈥? concrete is less than 28 days old
CPD庐鈥? liability shall be limited in all events to supplying
鈥? areas are exposed to extreme thermal shock s
鈥? areas are exposed to strong chemicals sufficient product to re-treat and/or repair the specific area
to which CPD庐 product has been applied. CPD庐 reserves
the right to have the true cause of any difficulty determined
COVERAGE
CIPADITE庐 CONDUCTIVE PRIMER: by accepted test methods. CPD庐 shall have no other
4 m虏/litre (163ft虏 per U.S. gallon) liability, including liability for incidental, consequential or
resultant damages, however caused, whether due to breach
CIPADOME庐 CONDUCTIVE: of warranty, negligence, or strict liability.
3m虏/litre (122ft虏 per U.S. gallon)
THIS WARRANTY MAY NOT BE MODIFIED OR
EXTENDED BY REPRESENTATIVES OF CPD庐, ITS
PACKAGING
CIPADOME庐 CONDUCTIVE is packaged in: DISTRIBUTORS OR DEALERS.
3.79 litre unit (1 U.S. gal)
18.9 litre unit (5 U.S. gal)
CLEAN UP
Clean all equipment and installation tools immediately
with CPD庐 Xylol. CPD庐 Xylol is a flammable solvent.
Read the M.S.D.S. before using.
STORAGE
Store in a heated warehouse. Storage at temperatures
below 4.5掳C (40掳F) may cause resin to crystallize.
SHELF LIFE
Three years from date of manufacture if kept in original
unopened containers under normal heated warehouse
conditions.
SAFETY PRECAUTIONS
Consult Material Safety Data Sheet (M.S.D.S.) for
specific instructions. MSDS # 313 + 313A
WARRANTY
The recommendations made and the information herein
is based on our own and independent laboratory
experience, and is believed to be accurate under
controlled conditions. However, no warranty or
guarantee of accuracy is made because we cannot cover
every possible application of product nor anticipate
every variation encountered in weather conditions, job-
conditions, methods used and types of surfaces on which
|