CIPADECKĀ® Membrane 60 LT
Polyurethane Waterproofing Membrane
DESCRIPTION Hardness (Shore A) . . . . . . . . . . . . . . . . . . . . . . 50
CIPADECKĀ® Membrane 60 LT is a solvent-based low
(ASTM D2240-86)
temperature cure high performance two component
Tensile Adhesion To Concrete . . 2.41Mpa (350 psi)
polyurethane waterproofing membrane.
(ASTM D4541)
Tear Strength . . . . . . . . . . . . . . 25KN/m (140 pli)
WHERE TO USE
CIPADECKĀ® Membrane 60 LT is primarily designed to (ASTM D624)
waterproof and protect structural slabs in most types of Abrasion Resistance . . . . . . . . . . . . . . . 20 mg loss
parking structures. This includes interior, above and (ASTM D4060)
below grade intermediate slabs, and ramps of new and
Taber Abrasion, CS-17 Wheel, 1000gm
restored parking structures.
The above information is representative of actual
CIPADECKĀ® Membrane 60 LT is also used to provide a
production runs. Independent test results may vary
traffic- bearing waterproof membrane on balcony decks
from the above by approximately Ā±10%.
, rooftop recreational areas, sun decks, pedestrian
walkways, plaza decks and plywood decks.
APPLICATION
SURFACE PREPARATION
BENEFITS
New concrete must be cured for a minimum of 28 days
ā? high solids coating; contains no TDI
before applying CIPADECKĀ® Membrane 60 LT.
ā? capable of bridging post application cracks up to 1.6
Surface should be primed using CIPADITEĀ® PRIMER
mm (1/16")
E-40 prior to application of CIPADECKĀ® Membrane
ā? cures at temperatures down to 2Ā°C (35Ā° F)
60 LT. Refer to the data sheet for instructions. The
ā? applied in a one coat application of 20 to 30 mils
substrate must be clean, dry and free of all dirt, waxes,
thickness
previously applied coatings, oil, grease, laitance and
ā? good adhesion to concrete and steel
any foreign matter that may interfere with the bond of
ā? has ample working time
the membrane to the substrate. Cracks and surface
defects should be repaired prior to application of the
Handling Properties (Tested @ 23Ā° (74Ā°)
membrane. All concrete and steel surfaces to be coated
Mix Ratio, by volume . . . . . . . . 10 parts A: 1 part B
should be shot blast, water blast or mechanically
Viscosity(Mixed) . . . . . . . . . . . . . . . 1500-2000 cps cleaned to provide a clean tooth for the coating.
Solids Content, by weight . . . . . . . . . . . . . . . . . 86 %
by volume . . . . . . . . . . . . . . . . 80 % DETAILING
Joints or cracks should be repaired prior to application
Mixed Weight (Density) 1.21kg/litre (10.1 lb./US gal)
of CIPADECKĀ® Membrane 60 LT. Cracks and cold
Pot Life . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 hours
joints less than 1.6mm (1/16") wide should be coated
Foot Traffic . . . . . . . . . . . . . . . . . . . . . . 16-24 hours
over with the CIPADECKĀ® Membrane 60 LT. All
Vehicular Traffic . . . . . . . . . . . . . . . . . . . . . . . 3 days
cracks and joints greater than 1.6mm (1/16") wide must
Full Cure and Maximum Resistance . . . . . . . . 7 days be routed and sealed with an approved polyurethane
sealant. The CIPADECKĀ® Membrane
60 LT must be extended a minimum distance of 50mm
DATA - Cured Film
(2") on either side of all sealed cracks, cold joints and
Tensile Elongation . . . . . . . . . . . . . . . . . 400-450 %
control joints to yield a total film thickness of 20-30
(ASTM D412)
mils dry.
Tensile Strength . . . . . . . . . . . 4-5 Mpa (580-725psi)
(ASTM D412)
0960-21-1105
MIXING STORAGE
CIPADECKĀ® Membrane 60 LT Part B will react with
The mixing equipment used to mix the membrane must be
clean and free of any contaminants that may be present in humidity and moisture. Keep containers tightly sealed;
the equipment from previously used products. Mix store upside down. Store in a heated warehouse. Do
component A first to eliminate the possibility of not freeze.
settlement. Pour all of the liquid from Part A and Part B
into the mixing equipment. A ā? Jiffy Mixerā? or a mud SHELF LIFE
mixer blade on a slow speed drill is the preferred method Six months from the date of manufacture if kept in
of mixing. Mix the blended components for a minimum original unopened containers under normal heated
of 2 minutes. warehouse conditions.
APPLICATION SAFETY PRECAUTIONS
Apply CIPADECKĀ® Membrane 60 LT to an even Consult Material Safety Data Sheet (M.S.D.S.) for
thickness using a squeegee and further level using a lint specific instructions. M.S.D.S.#232 & 232A
free 5mm nap roller (designed for epoxy and urethane), to
achieve a total thickness of 20 to 30 mils. Allow the WARRANTY
membrane to cure overnight before applying The recommendations made and the information herein
CIPADECKĀ® T-Coat. is based on our own and independent laboratory
experience, and is believed to be accurate under
The topcoat should be applied over the membrane within controlled conditions. However, no warranty or
the recoat time (24 hours). Otherwise roughening of guarantee of accuracy is made because we cannot cover
surface will be necessary to ensure good intercoat every possible application of product nor anticipate
adhesion. every variation encountered in weather conditions, job
conditions, methods used and types of surfaces on
which the product is applied. The users shall make their
LIMITATIONS
ā? do not apply CIPADECKĀ® Membrane 60 LT if the own tests to determine the suitability of such products
temperature is near dew point or relative humidity for any particular purpose.
exceeds 80 %.
ā? do not apply to a damp surface (use CIPADITEĀ® CPDĀ® makes no warranties with respect to this product,
PRIMER E-40) expressed or implied, including, without limitation, the
ā? remove from container only the amount of implied warranties of merchantability or fitness for a
CIPADECKĀ® Membrane 60 LT needed and reseal particular purpose.
the container immediately as it will begin to react
CPDĀ®ā? liability shall be limited in all events to
with moisture when exposed to ambient humidity s
supplying sufficient product to re-treat and/or repair the
specific area to which the CPDĀ® product has been
COVERAGE
applied. CPDĀ® reserves the right to have the true cause
Based on 20 mils thickness per coat:
1.6 mĀ²/litre (65 ftĀ²/U.S. gallon) of any difficulty determined by accepted test methods.
CPDĀ® shall have no other liability, including liability
Based on 30 mils thickness per coat: for incidental, consequential or resultant damages,
1.0 mĀ²/litre (41 ftĀ²/U.S. gallon) however caused, whether due to breach of warranty,
negligence, or strict liability.
PACKAGING
CIPADECKĀ® Membrane 60 LT is packaged in: THIS WARRANTY MAY NOT BE MODIFIED OR
3.79 litre/1 U.S. gal. unit EXTENDED BY REPRESENTATIVES OF
CPDĀ®,ITS DISTRIBUTORS OR DEALERS.
41.59 litre/11 U.S. gal. unit
CLEAN UP
Clean all equipment and installation tools immediately
with CPDĀ® Xylol . Read the M.S.D.S. for this product
prior to use.
|