CIPADITE庐 CONDUCTIVE PRIMER
Conductive Epoxy Primer
DESCRIPTION MIXING
CIPADITE庐 CONDUCTIVE PRIMER is a fast setting, The mixing equipment used to mix the primer must be
solvent-born low viscosity black conductive primer. clean and free of any contaminants that may be present in
the equipment from previously used products. Mix
component A first to eliminate the possibility of settlement.
WHERE TO USE
CIPADITE庐 CONDUCTIVE PRIMER is recommended Pour all of the liquid from Part A and Part B into the
for use with CIPADOME庐 SPARK PROOF. Its low mixing container. A 鈥? Jiffy Mixer鈥? or a mud mixer blade
viscosity allows the primer to penetrate deep into the on a slow speed drill is the preferred method of mixing.
concrete surface to seal the concrete from outgassing and Mix the blended components for a minimum of 2 minutes.
provide conductivity. It is imperative that the mixer be a slow speed model to
avoid damage and possible discoloration of the matrix.
BENEFITS
鈥? easy to apply APPLICATION
鈥? adheres well to both dry and damp surfaces Pour a workable amount of the mixed primer on to the
鈥? conductive prepared substrate and spread the material evenly with a
flat squeegee. Using a lint free 5 mm nap roller (designed
for epoxy and urethane), back roll the applied material to
Handling Properties
provide an even coat. (Substrate to receive primer must
Mix Ratio, by volume . . . . . . . . . . 3 Parts A : 1 Part B
have copper grounding rods in place prior to application.)
Viscosity (mixed) @ 23掳C (74掳F) . . . . . . . . . . 400 cps
Care should be taken not to overroll the material as air
Solids Content, by volume . . . . . . . . . . . . . . . . . . 48 % may become entrapped in the coating. Allow to stand for
by weight . . . . . . . . . . . . . . . . . . 40 % a minimum of 30-60 minutes prior to proceeding with
CIPADOME庐 SPARK PROOF installation.
Mixed Weight (Density) . . . 1.0 kg/litre (8.3 lb/US gal)
Pot Life @ 23掳C (74掳F) . . . . . . . . . . . . . . . . . . 4 hours
COVERAGE
Recoat time @ 23掳C (74掳F) . . . . . . . . . . . . . . 1-3 hours
Based on 5 mils dry film thickness per coat:
Full Cure and Maximum Resistance . . . . . . . . . 7 days
4 m虏/litre (163 ft虏/US gallon)
The above information is representative of actual PACKAGING
production runs. Independent test results may vary from CIPADITE庐 CONDUCTIVE PRIMER is packaged in:
the above by approximately 卤10%. 3.79 litres (1 US gal) units
15.0 litres (5 US gal) units
APPLICATION
SURFACE PREPARATION CLEAN UP
New concrete must be cured for a minimum of 28 days Clean all equipment and installation tools immediately
before applying CIPADITE庐 CONDUCTIVE PRIMER with CPD庐 Xylol . Read the M.S.D.S. for this product
The substrate must be above 10掳C (50掳F) and must be free prior to use.
of all dirt, waxes, previously applied coatings, oil, grease,
laitance and any foreign matter that may interfere with the STORAGE
bond of the primer to the prepared substrate. Cracks and Store in a heated warehouse. Do not freeze.
surface defects should be repaired prior to application of the
primer. All concrete and steel surfaces to be coated should SHELF LIFE
be shot blast, water blast or mechanically cleaned to Three years from the date of manufacture if kept in
provide a clean tooth for the primer application. If acid original unopened containers under normal heated
etching is the method of choice for preparation of the warehouse conditions.
concrete surface the etched surface must be thoroughly
flushed, neutralized and dry prior to application of the
primer.
0960-05-1105
SAFETY PRECAUTIONS
Consult Material Safety Data Sheet (M.S.D.S.) for specific
instructions see MSDS #286 + 286A.
WARRANTY
The recommendations made and the information herein is
based on our own and independent laboratory experience,
and is believed to be accurate under controlled conditions.
However, no warranty or guarantee of accuracy is made
because we cannot cover every possible application of
product nor anticipate every variation encountered in
weather conditions, job conditions, methods used and types
of surfaces on which the product is applied. The users shall
make their own tests to determine the suitability of such
products for any particular purpose.
CPD庐 makes no warranties with respect to this product,
expressed or implied, including, without limitation, the
implied warranties of merchantability or fitness for a
particular purpose.
CPD庐鈥? liability shall be limited in all events to supplying
s
sufficient product to re-treat and/or repair the specific area
to which the CPD庐 product has been applied. CPD庐
reserves the right to have the true cause of any difficulty
determined by accepted test methods. CPD庐 shall have no
other liability, including liability for incidental,
consequential or resultant damages, however caused,
whether due to breach of warranty, negligence, or strict
liability.
THIS WARRANTY MAY NOT BE MODIFIED OR
EXTENDED BY REPRESENTATIVES OF CPD庐,ITS
DISTRIBUTORS OR DEALERS.
|