CIPADITE庐 HI
Fast Setting High Impact Epoxy Resin
DESCRIPTION APPLICATION
CIPADITE庐 HI is a very rapid setting, 100% solids low SURFACE PREPARATION
viscosity flexible hybrid urethane epoxy resin. It is New concrete must be cured for a minimum of 28 days
before applying CIPADITE庐 HI. The substrate must be
versatile product that can be used as primer, adhesive or
binder. above 10掳C (50掳F) and must be free of all dirt, waxes,
previously applied coatings, oil, grease, laitance and any
foreign matter that may interfere with the bond of the
WHERE TO USE
CIPADITE庐 HI is recommended for use with primer to the prepared substrate. Cracks and surface defects
CIPADOME庐 HI epoxy flooring as well as CIPADECK庐 should be repaired prior to the application of the primer. All
membrane systems. Its low viscosity allows the primer to concrete and steel surfaces to be coated should be shot
penetrate deep into the concrete surface to seal the blasted, water blasted or mechanically cleaned to provide a
concrete from outgassing. clean tooth for the primer application. If acid etching is the
method of choice for preparation of the concrete surface the
etched surface must be thoroughly flushed, neutralized and
BENEFITS
鈥? 100% solids, with no offensive odor, zero VOC鈥檚 dry prior to application of the primer.
鈥? easy to apply
鈥? excellent bond to concrete and steel MIXING
鈥? color coded to ensure uniform mixing The mixing equipment used to mix the primer must be clean
鈥? convenient one to one mixing ratio and free of any contaminants that may be present in the
鈥? approved by Canadian Food Inspection Agency equipment from the previously used products. Mix
component A and B individually first to eliminate the
possibility of settlement. Pour all of the liquid from Part A
Handling Properties
and Part B into the mixing container. A 鈥? Jiffy Mixer鈥檕n a
Mix Ratio, by volume . . . . . . . . . . . 1 part A: 1 part B
slow speed drill is the preferred method of mixing. Mix the
Viscosity (Mixed) @ 25掳C (77掳F) . . . . . . . . . 1000 cps
blended components for a maximum of 1 minute until a
Solids Content . . . . . . . . . . . . . . . . . . . . . . . . . 100 % uniform grey color is achieved.
Mixed Weight (Density) . 1.05 kg/litre (8.8 lb/US gal)
Pot Life @ 25掳C (77掳F) . . . . . . . . . . . . . . . 8 minutes APPLICATION
Pour a workable amount of the mixed primer on to the
Thin Film Set Time @ 25掳C (77掳F) . . . . . . . . . 3 hours
prepared substrate and spread the material evenly with a
Foot Traffic @ 25掳C (77掳F) . . . . . . . . . . . . . . 5 hours
flat squeegee. Using a lint free 5 mm nap roller (designed
Full Cure and Maximum Resistance . . . . . . . . . 7 days
for epoxy and urethane), back roll the applied material to
Color . . . . . . . . . . . . . . . . . . . . Clear, Tile Red, Grey
provide an even coat. Care should be taken not to overroll
the material as air may become entrapped in the coating.
DATA - Cured Film LIMITATIONS
Do not apply CIPADITE庐 HI:
Pull Out Tensile Adhesion to concrete: . . . . . 400 psi
鈥? if the substrate and ambient temperatures are below
(concrete failure)
10掳C (50掳F)
Tensile Strength . . . . . . . . . . . . . . 15 Mpa (2200 psi)
鈥? do not apply to damp concrete
(ASTM D638)
Elongation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80% COVERAGE
(ASTM D638) Based on 5 mils thickness per coat:
8 m虏/litre (325 ft虏/U.S. gallon)
The above information is representative of actual
production runs. Independent test results may vary from
the above by approximately 卤10%.
0960-03-1105
PACKAGING
CIPADITE庐 HI is packaged in:
7.58 litre/2 U.S. gal. units
37.9 litre/10 U.S. gal. units
CLEAN UP
Clean all equipment and installation tools immediately
with CPD庐 Xylol. Read the M.S.D.S. for this product
prior to use.
STORAGE
Store in a heated warehouse.
SHELF LIFE
Three years from the date of manufacture if kept in
original unopened containers under normal heated
warehouse conditions.
SAFETY PRECAUTIONS
Consult Material Safety Data Sheet (M.S.D.S.) for
specific instructions. MSDS # 295 + 295A
WARRANTY
The recommendations made and the information herein is
based on our own and independent laboratory experience,
and is believed to be accurate under controlled conditions.
However, no warranty or guarantee of accuracy is made
because we cannot cover every possible application of
product nor anticipate every variation encountered in
weather conditions, job conditions, methods used and types
of surfaces on which the product is applied. The users
shall make their own tests to determine the suitability of
such products for any particular purpose.
CPD庐 makes no warranties with respect to this product,
expressed or implied, including, without limitation, the
implied warranties of merchantability or fitness for a
particular purpose.
CPD庐鈥? liability shall be limited in all events to supplying
s
sufficient product to re-treat and/or repair the specific area
to which the CPD庐 product has been applied. CPD庐
reserves the right to have the true cause of any difficulty
determined by accepted test methods. CPD庐 shall have no
other liability, including liability for incidental,
consequential or resultant damages, however caused,
whether due to breach of warranty, negligence, or strict
liability.
THIS WARRANTY MAY NOT BE MODIFIED OR
EXTENDED BY REPRESENTATIVES OF CPD庐,ITS
DISTRIBUTORS OR DEALERS.
|