CIPADITE庐 GEL 15
Fast curing epoxy adhesive gel
particles and all foreign contamination. All concrete should
DESCRIPTION
CIPADITE庐 GEL 15 is a 100% solids two component, be chemically cleaned or mechanically scarified for best
high modulus high strength, moisture insensitive fast results. New concrete should be cured 30 days and any
setting epoxy adhesive gel. surface laitance or curing compound must be removed.
For anchorages, core holes should be scored, free of all
WHERE TO USE
CIPADITE庐 GEL 15 is recommended for bonding new dust and mud and dry for maximum bond. Holes should be
concrete to old concrete, repairing spalled, scaled and of a minimum of 4 mm greater in diameter than the
cracked concrete, structural bonding adhesive for vertical anchor. Anchorages must be free of all rust, scale and mill
dowels and anchors, bonding of precast concrete units, oil. A solvent wash is recommended for all anchorages
steel plates or other metal sections to concrete and crack prior to installation. Fill holes to slight excess required,
sealing for epoxy injection work. insert anchorage and rotate slowly to assure that no air
pockets remain.
BENEFITS
鈥? excellent adhesion properties. Steel surfaces should be free of dirt, grease, oil or rust.
鈥? very easy to mix and apply Blast surface using an angular medium such as aluminum
鈥? cures under cool, damp conditions oxide or grit to SSPC-SP10 standard, with a minium
鈥? rapid development of hardness and mechanical profile of 2.5 mils. Where sandblasting is not practical,
strengths the surface should be degreased and mechanically
鈥? moisture insensitive during the cure abraded to reveal continuous bright metal.
鈥? high shear and tensile strength
MIXING
PROPERTIES (Tested @ 23"C (74"F) Premix each component separately before using. Combine
2 parts (by volume) of Part A with 1 part (by volume) of
Mix Ratio, by Volume . . . . . . . . . . . 2 parts A:1 part B
Part B. Mix with a low speed drill. Thoroughly blend the
Viscosity (Mixed) . . . . . . . . . . . . . . . thixotropic paste
material until an even consistency is achieved, periodically
Pot-Life 100g . . . . . . . . . . . . . . . . . . . . . . 15 minutes
scraping down sides and bottom of container. Apply as
Initial cure . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 hours soon as possible as pot life is limited.
Full Cure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 days
Tensile Strength . . . . . . . . . . . . . . 28 MPa (4000 psi) LIMITATIONS
CIPADITE庐 Gel 15 is not recommended for:
(ASTM D638)
? applications where ambient temperature are below
Tensile Elongation . . . . . . . . . . . . . . . . . . . . . . . . 2 %
10掳C (50掳F)
(ASTM D638)
? underwater application
Compressive Strength . . . . . . . . . . 60 MPa (8700 psi)
(ASTM D695) 7 days COVERAGE
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . clear Bonding Adhesive 2.0 m虏/L (81.5 ft虏/U.S. gal)(smooth
surface).
The above information is representative of actual
PACKAGING
production runs. Independent test results may vary from
3.79L (1 U.S. gal)
the above by approximately 卤 10 %.
18.9L (5 U.S gal.)
APPLICATION
SURFACE PREPARATION
Concrete should be sound and free from dust, loose
0393-03-1105
CLEAN UP
Clean all equipment with CPD庐 Xylol before epoxy
hardens. CPD庐 Xylol is a flammable solvent. Read the
Material Safety Data Sheet before using.
STORAGE
Store in a heated warehouse. Storage at temperatures
below 4.5掳C (40掳F) may cause the resin to crystallize.
SHELF LIFE
Two years if kept in original unopened containers under
normal warehouse conditions.
SAFETY PRECAUTIONS
Consult Material Safety Data Sheet ( M.S.D.S.)
for specific instructions. M.S.D.S. # 306, 306A
WARRANTY
The recommendations made and the information herein is
based on our own and independent laboratory experience,
and is believed to be accurate under controlled conditions.
However, no warranty or guarantee of accuracy is made
because we cannot cover every possible application of
product nor anticipate every variation encountered in
weather conditions, job-conditions, methods used and
types of surfaces on which the product is applied. The
users shall make their own tests to determine the suitability
of such products for any particular purpose.
CPD庐 makes no warranties with respect to this product,
expressed or implied, without limitation, the implied
warranties of merchantability or fitness for a particular
purpose.
CPD庐鈥? liability shall be limited in all events to supplying
s
sufficient product to re-treat and/or repair the specific area
to which CPD庐product has been applied. CPD庐 reserves
the right to have the true cause of any difficulty determined
by accepted test methods. CPD庐 shall have no other
liability, including liability for incidental, consequential or
resultant damages, however caused, whether due to breach
of warranty, negligence, or strict liability.
THIS WARRANTY MAY NOT BE MODIFIED OR
EXTENDED BY REPRESENTATIVES OF CPD庐, ITS
DISTRIBUTORS OR DEALERS.
|