CPD® SALTGUARD ULTRA
DESCRIPTION APPLICATION
CPD® Saltguard Ultra is part of a two coat protection INSTALLATION:
CPD® Saltguard contains blended solvents and should be
system which prevents the intrusion of chlorides and water.
The two coat system consists of: handled accordingly. Do not use near fire or extreme heat
A) A base coat of CPD® Saltguard. It is an oligomeric and provide good ventilation to avoid build up of solvent
alkyl-alkyloxy siloxane. This penetrates into the substrate fumes. Applicators should wear approved NIOSH/MSHA
and reduces chloride ion migration through cement materials. approved respirators. When applying to exterior of
B) The top coat is CPD® Paver and Concrete Sealer. It is occupied buildings, all exterior air conditioning vents
a colorless methacrylate copolymer resin in a solvent base. should be covered during application and air handling
equipment should be turned off during application to avoid
solvent odors within the building. Clothing which may
WHERE TO USE
� concrete slabs, decks, walls, abutments, concrete barriers become contaminated with Saltguard should be changed as
and retaining walls quickly as possible.
BENEFITS PREPARATORY WORK:
� an effective chloride screen A test application is necessary on each surface and/or
� excellent freeze-thaw resistance masonry material to be treated to ensure compatibility and
� prolongs the surface life and prevents damage from desired results. Test areas are also useful in determining
within by maintaining vapor permeability of concrete final application rate and procedures.
� greatly reduces effects from salt scaling Tests should be applied using the same equipment as for
� excellent penetration into substrate the job application. Test areas should be inspected by the
� eliminate development of efflorescence engineer throughout the job application.
� protects concrete surface from penetration and staining by Adjoining glass, metal and painted surfaces should be
protected from over spray and splash of CPD® Saltguard.
oil, grease, deicing salts and other contaminants
Splashes should be removed using mineral spirits before
the solution has dried on the surface.
PROPERTIES
All caulking, patching and joint sealants should be
CPD® Paver &
Test Saltguard
installed prior to application of CPD® Saltguard. The
Concrete Sealer
concrete surface should be clean, free of dust, surface dirt
and contaminants. New concrete should be thoroughly
Classification Penetrant Sealer
cured before application of CPD® Saltguard. New concrete
Maximum water pass pass normally does not require etching, however slick trowel
absorption by mass finished concrete that has been contaminated with surface
of concrete is 1% dirt, tire marks, etc. during construction may require
thorough cleaning and a mild etch for best performance of
Minimum moisture pass pass
the sealer. Older concrete surfaces should be power
vapor loss is 95%
washed with high pressure and appropriate cleaners to
assure removal of surface dirt, oil and contaminants.
Maximum chloride pass pass
Surfaces to be treated may be damp, but should be
ion content @ 13-
absorbent to assure good penetration of CPD® Saltguard.
25mm depth is 0.02%
by mass of concrete.
Note: If a chemical curing agent is to be used during
Salt Scaling pass pass installation of new concrete, a test area is recommended
Resistance maximum prior to general application to assure compatibility. It is
loss in mass after 50 impossible to assure compatibility with all products.
cycles is 0.80kg/m²
0719-04-1105
PLACING: PACKAGING
CPD® Saltguard should be applied as packaged. Do not 208L (55 U.S. gal) drum
dilute or alter material. Preferred method of application is 18.9L (5.3 U.S. gal) pail
with a low pressure (20 psi) airless sprayer or with a heavily
saturated brush or roller. Sprayer should be fitted with a CLEAN UP
solvent resistant hose and gasket. When using brushes or Clean equipment immediately after use with Xylene
rollers, care should be taken to assure that enough solution solvent.
is applied. Apply sufficient material to thoroughly saturate
the surface making sure to brush out excess material that STORAGE
does not penetrate. Store under normal heated warehouse conditions.
When applying to flat surfaces, CPD® Saltguard should be SHELF LIFE
applied in a single saturating application with sufficient Two years from date of manufacture when stored in
material applied so that the surface remains wet for a few original unopened container, and under normal heated
minutes before penetration into the concrete. Surface warehouse conditions.
residues, pools and puddles should be broomed out
thoroughly until they completely penetrate the surface. SAFETY PRECAUTION
Flammable Liquid. Consult Material Safety Data Sheet
CPD® Paver and Concrete Sealer should be applied to a dry (M.S.D.S.) for specific instructions. MSDS # 122.
surface which is normally 24 hours after the application of
Saltguard. Application of the top coat may be by brush, WARRANTY
roller or spray depending on surface conditions. Refer to The recommendations made and the information herein is
CPD® Paver and Concrete Sealer product data sheet for based on our own and independent laboratory experience,
further information. and is believed to be accurate under controlled conditions.
However, no warranty or guarantee of accuracy is made
because we cannot cover every possible application of
LIMITATIONS
� do not apply at temperatures below 4.5°C (40°F) product nor anticipate every variation encountered in
� after applying CPD® Saltguard, protect from rain, foot weather conditions, job-conditions, methods used and
traffic and sun for 24 hours types of surfaces on which the product is applied. The
� after application of CPD® Paver and Concrete Sealer users shall make their own tests to determine the suitability
wait 24 hours before opening to traffic of such products for any particular purpose.
CPD® makes no warranties with respect to this product,
COVERAGE
CPD® Saltguard: expressed or implied, without limitation, the implied
Broom Finish 3.4 - 4.4m²/L warranties of merchantability or fitness for a particular
(140-180 ft²/U.S. gal) purpose.
Slick Trowel Finish 5.9 m²/L (240 ft²/U.S. gal)
CPD®� liability shall be limited in all events to supplying
s
Older Concrete 2.3 - 3.4m²/L sufficient product to re-treat and/or repair the specific area
to which CPD® product has been applied. CPD® reserves
(95-140 ft²/U.S. gal)
CPD® Paver and Concrete Sealer: 6m²/L the right to have the true cause of any difficulty determined
by accepted test methods. CPD® shall have no other
(250 ft²/U.S. gal)
liability, including liability for incidental, consequential or
resultant damages, however caused, whether due to breach
Note: Some extremely dense concrete materials contain
of warranty, negligence, or strict liability.
integral waterproofing agents and admixtures. These
surfaces require very little Saltguard and consumption rates
THIS WARRANTY MAY NOT BE MODIFIED OR
of 7.4 - 8.6 m²/L (300-350 ft²/U.S. gal) are adequate.
EXTENDED BY REPRESENTATIVES OF CPD®, ITS
DISTRIBUTORS OR DEALERS.
STANDARDS
Manufactured to comply with Ministry of Transportation,
Ontario (MTO) for use on all projects (Test M1-127).
|