CIPADITE庐 PRIMER ST
Fast Setting General Purpose Epoxy Primer
waxes, previously applied coatings, oil, grease, laitance
DESCRIPTION
CIPADITE庐 PRIMER ST is a fast setting, 100% solids, and any foreign matter that may interfere with the bond of
low viscosity epoxy primer for dry substrates only. the primer to the prepared substrate. Cracks and surface
defects should be repaired prior to the application of the
primer. All concrete and steel surfaces to be coated should
WHERE TO USE
CIPADITE庐 PRIMER ST is recommended for use with be shot blast or mechanically cleaned to provide a clean
CPD庐 Epoxy flooring systems. Its low viscosity allows the tooth for the primer application. If acid etching is the
primer to penetrate deep into the concrete surface to seal method of choice for preparation of the concrete surface,
the concrete from out gassing. the etched surface must be thoroughly flushed and dry
prior to application of the primer.
BENEFITS
鈥? 100% solids, with no offensive odors, zero VOC鈥檚 MIXING
鈥? easy to apply The mixing equipment used to mix the primer must be
鈥? excellent bond to concrete and steel. clean and free of any contaminants that may be present in
鈥? available in clear and a wide range of colors. the equipment from previously used products. Mix
(See color chart) component A first to eliminate the possibility of settlement.
Pour all of the liquid from Part A and Part B into the
mixing container. A 鈥? Jiffy Mixer鈥? or a mud mixer on a
Handling Properties
slow speed drill is the preferred method of mixing. Mix
Mix Ratio, by volume . . . . . . . . . . 2 parts A: 1 part B
the blended components for a minimum of 3 minutes.
Viscosity (Mixed) @ 23掳C (74掳F) . . . . . . . . . . 500 cps
Solids Content . . . . . . . . . . . . . . . . . . . . . . . . . 100 % APPLICATION
Mixed Weight (Density).......1.1kg/litre (9.2 lb./US gal) Pour a workable amount of the mixed primer on to the
Pot Life @ 23掳C (74掳F) . . . . . . . . . . . . . . 12 minutes prepared substrate and spread the material evenly with
a flat squeegee. Using a lint free 5 mm nap roller
Recoat time @ 23掳C (74掳F) . . . . . . . . . . . . . . 3 hours
(designed for epoxy and urethane), back roll the applied
Foot Traffic @ 23掳C (74掳F) . . . . . . . . . . . . . 10 hours
material to provide an even coat. Care should be taken not
Full Cure and Maximum Resistance . . . . . . . . . 7 days
to overroll the material as air may become entrapped in
the coating.
DATA - Cured Film
Pull Out Tensile Adhesion to concrete . . . . . . 400 psi LIMITATIONS
Do not apply CIPADITE庐 PRIMER ST:
(ASTM D4541) (concrete failure)
鈥? if the substrate and ambient temperatures are below
Tensile Strength . . . . . . . . . . . . . . 25 Mpa (3600 psi)
10掳C (50掳F)
(ASTM D638)
鈥? do not apply to damp concrete
Tensile Elongation . . . . . . . . . . . . . . . . . . . . . . . 8%
(ASTM D638) COVERAGE
Based on 5 mils thickness per coat:
8 m虏/litre (325 ft虏/U.S. gallon)
The above information is representative of actual
production runs. Independent test results may vary from
PACKAGING
the above by approximately 卤10%.
CIPADITE庐 PRIMER ST is packaged in:
3.79 litre/1 U.S. gal. units
APPLICATION
11.4 litre/ 3 U.S. gal. units
SURFACE PREPARATION
56.7 litre/15 U.S. gal. units
New concrete must be cured for a minimum of 28 days
before applying CIPADITE庐 PRIMER ST. The substrate
must be above 10掳C (50掳F) and must be free of all dirt,
0960-01-1105
CLEAN UP
Clean all equipment and installation tools immediately
with CPD庐 Xylol or Sure Klean庐 Asphalt and Tar
Remover. Read the M.S.D.S. for this product prior to use.
STORAGE
Store in a heated warehouse. Do not freeze.
SHELF LIFE
Three years from the date of manufacture if kept in
original unopened containers under normal heated
warehouse conditions.
SAFETY PRECAUTIONS
Consult Material Safety Data Sheet (M.S.D.S.) #276 +
276A (Colored), #276B + 276C (Clear) for specific
instructions.
WARRANTY
The recommendations made and the information herein is
based on our own and independent laboratory experience,
and is believed to be accurate under controlled conditions.
However, no warranty or guarantee of accuracy is made
because we cannot cover every possible application of
product nor anticipate every variation encountered in
weather conditions, job conditions, methods used and types
of surfaces on which the product is applied. The users
shall make their own tests to determine the suitability of
such products for any particular purpose.
CPD庐 makes no warranties with respect to this product,
expressed or implied, including, without limitation, the
implied warranties of merchantability or fitness for a
particular purpose.
CPD庐鈥? liability shall be limited in all events to supplying
s
sufficient product to re-treat and/or repair the specific area
to which the CPD庐 product has been applied. CPD庐
reserves the right to have the true cause of any difficulty
determined by accepted test methods. CPD庐 shall have no
other liability, including liability for incidental,
consequential or resultant damages, however caused,
whether due to breach of warranty, negligence, or strict
liability.
THIS WARRANTY MAY NOT BE MODIFIED OR
EXTENDED BY REPRESENTATIVES OF CPD庐, ITS
DISTRIBUTORS OR DEALERS.
|