CIPADAM庐 S-40
DESCRIPTION TEST DATA - Continued
CIPADAM庐 S-40 is a clear, penetrating, breathable sealer A. NCHRP 244 Report (continued)
that contains a 40 percent solution of silane in an alcohol
Scaling Resistance
carrier. CIPADAM庐 S-40 chemically reacts with the
(ASTM C-672) 50 cycles...................................2.0
concrete substrate to produce a long lasting water repellent
OPS 1351.08.01 50 cycles ..................................1.0
effect. This material鈥? small molecular structure allows
s
B. Alberta Department of Transportation
for maximum penetration into any silicous material to
form an alkali resistant polysiloxane. i) Alberta DOT - Waterproofing
Before Sandblasting ..................................85.3%
WHERE TO USE After Sandblasting ....................................83.3%
Applications include parking garages, building envelopes,
ii) Alberta DOT - Sealer Test Type 1b (70% moisture)
ramps and other concrete structures.
Before Sandblasting ..................................89.0%
After Sandblasting ....................................82.2%
BENEFITS
鈥? excellent resistance to water intrusion
鈥? excellent resistance to chloride ion ingress The above information is representative of actual
鈥? breathable production runs. Independent test results may vary from
鈥? no change in surface appearance the above by approximately 卤10%
鈥? high resistance to alkali attack
鈥? reduces the effects of efflorescence, mildew, and PRECAUTIONS
stains on vertical concrete and masonry structures This product contains blended solvents and alcohol
should be handled accordingly. Do not use near fire or
PROPERTIES extreme heat and provide good ventilation to avoid
buildup of solvent fumes. Applicators should wear
Solvent Base .....................................Alcohol
approved NIOSH/MSHA approved respirators. When
Active Substance Content: ...............40% by weight
applying to exteriors of occupied buildings, all exterior
Specific Gravity: ..............................0.83
air conditioning vents should be covered during
Viscosity: ........................................ 5-10 cps application and air handling equipment should be turned
Flash Point: (T.C.C.)....................... 12掳C (54掳F) off during application to avoid solvent odors within the
Color and Finish: .............................Clear, invisible building. Clothing which may become contaminated with
CIPADAM庐 S-40 should be changed as quickly as
possible.
TEST DATA
The 40% (wt) silane that is in the CIPADAM庐 S-40 has
SURFACE PREPARATION
been tested according to the most current test procedures
Caulking and patching materials must be fully cured
in the industry. The results are listed below:
before applying CIPADAM庐 S-40. All substrates must
A. NCHRP 244 Report be properly cleaned and free of dust and contaminants
Series 1 Test: 83.8% Reduction in Water Absorption before the application of the sealer. Acceptable surface
cleaning methods include shot blasting, sand blasting, and
82.7% Reduction in Chloride Intrusion
water blasting for a concrete slab. Usually no
111.4% Water Vapor Transmission
preparation is required for building envelopes unless the
Series IV Test:
substrate has surface dirt or contaminants on it. Do not
97.6% Reduction in Chloride Ion Reduction
apply to a wet substrate, although a damp substrate may
Freeze-thaw Durability (ASTM C-666) be treated.
Relative Dynamic Modulus of Elasticity.................95.3
NOTE: If a chemical curing agent has been used during
installation of new concrete, it must be removed prior to
the application of the sealer.
0719-05-1105
APPLICATION PACKAGING
CIPADAM庐 S-40 should be applied as packaged - do not 208L (55 U.S. gal) drums - 190 kg (419 lb)/drum
dilute or alter material. Preferred method of application is 18.9L (5 U.S. gal) pail - 21 kg (47 lb)/pail
with low pressure (20 psi) airless spray equipment or with 3.79L (1 U.S. gal) pail - 5 kg (11 lb)/pail
heavily saturated brush or roller. Sprayer should be fitted
with solvent resistant hoses and gaskets. When using CLEAN UP
Clean up with CPD庐 Xylol.
brushes or rollers, care should be taken to ensure that
enough solution is applied. Apply sufficient material to
thoroughly saturate the surface making sure to brush out STORAGE
excess material that does not penetrate. Contains flammable solvents. Keep away from open
flame. Keep containers tightly closed when not in use.
HORIZONTAL SURFACE APPLICATIONS SHELF LIFE
This product should be applied in a single saturating Three years from date of manufacture when stored in
application with sufficient material so that it should pond original unopened container, and under normal warehouse
on the surface at least 5 seconds before being absorbed. conditions.
Surface residues, pools and puddles should be broomed
out thoroughly until they completely penetrate into the SAFETY PRECAUTION
surface. Protect from vehicular traffic for 24 hours. Flammable Liquid. Consult Material Safety Data Sheet
(M.S.D.S.) for specific instructions. MSDS #270.
VERTICAL SURFACE APPLICATION
This product should be applied in a flooding application WARRANTY
from the bottom-up so the material runs down 6"-8" (15- The recommendations made and the information herein is
20 cms) below the spray pattern. On porous substrates, based on our own and independent laboratory experience,
this product should be applied in two 鈥渨et-on-wet鈥? and is believed to be accurate under controlled conditions.
applications. Allow the first application to penetrate the However, no warranty or guarantee of accuracy is made
surface and re-apply in the same manner. because we cannot cover every possible application of
product nor anticipate every variation encountered in
weather conditions, job-conditions, methods used and
MAINTENANCE
Chemical spills, salts and abrasives should be removed types of surfaces on which the product is applied. The
from the surfaces as soon as possible. users shall make their own tests to determine the
suitability of such products for any particular purpose.
LIMITATIONS
CPD庐 makes no warranties with respect to this product,
鈥? not intended for below-grade waterproofing
鈥? it can be applied at temperatures down to -7掳C (20掳F) expressed or implied, without limitation, the implied
providing no ice or frost exists in or on the surface warranties of merchantability or fitness for a particular
鈥? do not apply if the ambient temperature of the surface purpose.
exceeds 38掳C (100掳F)
CPD庐鈥? liability shall be limited in all events to supplying
鈥? do not apply if rain is expected within 4 hours s
鈥? if rain has preceded the application, the surface should sufficient product to re-treat and/or repair the specific
area to which CPD庐 product has been applied. CPD庐
be allowed to dry for at least 24 hours
鈥? this material should be stored in sealed containers and reserves the right to have the true cause of any difficulty
determined by accepted test methods. CPD庐 shall have
kept away from extreme heat
no other liability, including liability for incidental,
consequential or resultant damages, however caused,
COVERAGE
Porosity and texture of the concrete and masonry surface whether due to breach of warranty, negligence, or strict
will affect the amount of material necessary for effective liability.
treatment. The following is a guide for estimating material
requirements for concrete. Always test on the actual THIS WARRANTY MAY NOT BE MODIFIED OR
EXTENDED BY REPRESENTATIVES OF CPD庐, ITS
surface to get precise consumption rates.
Concrete: 3-5m虏/L (120-200 ft虏/U.S. gallon) depending on DISTRIBUTORS OR DEALERS.
porosity
|