CIPADECKĀ® MR System
Mechanical Room Waterproofing System
DESCRIPTION PROPERTIES
CIPADECKĀ® MR System is a 100 % solids multi- coat CIPADECKĀ® CIPADORĀ®
waterproofing system. It consists of an amine cured Membrane 100 E-400
polyurethane elastomeric membrane, CIPADECKĀ® Handling Properties (tested @ 23Ā° C (74Ā° F)
Membrane 100, and a tough flexible wear and slip resistant Mix Ratio, by volume, A/B 2/1 2/1
epoxy topcoat, CIPADORĀ® E-400. Together, they provide an
attractive durable monolithic waterproofing system. Viscosity (Mixed), cps 3000 3000
WHERE TO USE Mixed Weight (Density),
CIPADECKĀ® MR System is a cold applied deck coating kg/litre (Ib/ gal.) 1.07 (8.9) 1.43
system, primarily designed for waterproofing mechanical (11.8)
equipment rooms.
Solids Content 100 % 100 %
BENEFITS
Pot Life 2 hours 20 minutes
ā? contains NO ISOCYANATE
Set Time 16 hours 6-8 hours
ā? 100% solids, odorless with zero VOCā? s
Full Cure 7 days 7 days
ā? moisture insensitive during the application and
throughout the cure (not affected by humidity)
DATA - Cured Film (7 days Cured @ RT/ 50% RH)
ā? long pot life and easy to apply
Elongation
ā? very good color stability and weather resistance
(ASTM D 412) 325% -
ā? tough, resilient and abrasion resistant
(ASTM D638) - 80%
ā? CIPADECKĀ® Membrane 100 retains its integrity even if
substrate movement causes hairline cracks up to 1.6 mm
Tensile Strength, MPa (psi)
(1/16")
(ASTM D 412) 4.5 (650) -
ā? available in a wide range of standard colors
(ASTM D638) - 11 (1600)
APPLICATION Shore Hardness 30 A 60 D
SURFACE PREPARATION ASTM D2240
New concrete must be cured for a minimum of 28 days before
applying CIPADECKĀ® MR System. The substrate must be Tear Strength KN/m (pli) 12 (68.5) -
above 10Ā°C (50Ā°F) and must be free of all dirt, waxes, (ASTM 624)
previously applied coatings, oil, grease, laitance and any
foreign matter that may interfere with the bond of the coating Tensile Adhesion to concrete, (psi) 2.4 (350)2.8
MPa
to the substrate. Cracks and surface defects should be (400)
repaired prior to application of the coating. All concrete and (ASTM D4541)
steel surfaces to be coated should be shot blast, water blast or
Chloride Permeability 0 Coulombs
mechanically cleaned to provide a clean tooth for the coating.
(AASHTO T-2770)
DETAILING
Abrasion Resistance, mg loss- 120 100
Joints or cracks should be repaired prior to application of
(ASTM D4060, Taber, CS-17, 1000 cycles)
CIPADECKĀ® MR System. Cracks and cold joints less than
1.6mm (1/16") wide should be coated over with the
Chemical Resistance
CIPADECKĀ® Membrane 100. All cracks and joints greater
no effect from water, motor oils, gasoline, anti-freeze, alkalis, salts
than 1.6mm (1/16") wide must be routed and sealed with an and common household chemicals.
approved polyurethane sealant. The CIPADECKĀ® Membrane
100 must be extended a minimum distance of 50 mm (2") on
The above information is representative of actual
either side of all sealed cracks, cold joints and control joints
production runs. Independent test results may vary from
to yield a total film thickness of 20-30 mils dry.
the above by approximately Ā± 10%.
0960-26-1105
CIPADORĀ® E-400:
MIXING
The mixing equipment used to mix the coating must be Based on 5 mils thickness per coat:
clean and free of any contaminants that may be present in 8 mĀ²/litre (325 ftĀ²/US gallon)
the equipment from previously used products. Mix
component A first to eliminate the possibility of PACKAGING
CIPADECKĀ® Membrane 100:
settlement. Pour all of the liquid from Part A and Part B
into the mixing equipment. A ā? Jiffy Mixerā? or a mud 3.79 litre/1 U.S. gal. units
mixer blade on a slow speed drill is the preferred 11.4 litre/3 U.S. gal. units
method of mixing. Mix the blended components for a 56.7 litre/15 U.S. gal. units
minimum of 2 minutes.
CIPADORĀ® E-400:
APPLICATION 3.79 litre (1 U.S. gallon)
Membrane Installation: 11.4 litre (3 U.S. gallons)
Apply CIPADECKĀ® Membrane 100 to an even thickness 56.7 litre (15 U.S. gallons)
using a squeegee and further level using a lint free 5mm
nap roller (designed for epoxy and urethane) to achieve a CLEAN UP
total thickness of 20 to 40 mils. Allow the membrane to Clean all equipment and installation tools immediately with
cure overnight before applying CIPADORĀ® E-400. CPDĀ® Xylol . Read the M.S.D.S. for this product prior to use.
Topcoat Installation: STORAGE
Apply CIPADORĀ® E-400 with a lint free 5mm nap roller Store in a heated warehouse. Do not freeze.
(designed for epoxy and urethane) in a one coat
application to achieve a film thickness of 5-8 mils. SHELF LIFE
CIPADORĀ® E-400 is a fast setting enamel. As soon as Three years from the date of manufacture if kept in original
the Part A and Part B are thoroughly mixed, spread the unopened containers under normal heated warehouse
material quickly onto the cured membrane surface. conditions.
Lightly seed the wet film with 50 mesh silica and back
roll to encapsulate the aggregate into the coating. If a SAFETY PRECAUTIONS
smooth finish is desired, apply a second coat of Consult Material Safety Data Sheet (M.S.D.S.) for specific
CIPADORĀ® E-400. Allow the coating to cure overnight. instructions. CIPADECKĀ® Membrane 100 MSDS # 294 +
294a, + CIPADORĀ® E-400 MSDS # 241 + 242.
LIMITATIONS
ā? do not apply CIPADECKĀ® MR System if the WARRANTY
substrate and ambient temperatures are below 10Ā°C The recommendations made and the information herein is
(50Ā°F). based on our own and independent laboratory experience, and
ā? CIPADECKĀ® MR System is designed for thin film is believed to be accurate under controlled conditions.
thickness applications that necessitate that the deck However, no warranty or guarantee of accuracy is made
surface to be relatively smooth. because we cannot cover every possible application of
ā? do not apply to a damp surface product nor anticipate every variation encountered in weather
ā? prime with CIPADITEĀ® Primer DS when the conditions, job conditions, methods used and types of
concrete substrate is damp prior to the application of surfaces on which the product is applied. The users shall
CIPADORĀ® MEMBRANE 100. make their own tests to determine the suitability of such
ā? CIPADECKĀ® MR System is not recommended for products for any particular purpose.
exterior application. It may slightly discolor upon
CPDĀ® makes no warranties with respect to this product,
direct exposure to sunlight
expressed or implied, including, without limitation, the
COVERAGE implied warranties of merchantability or fitness for a
CIPADECKĀ® Membrane 100: particular purpose.
Based on 20 mils thickness per coat:
2 mĀ²/litre (80 ftĀ²/U.S. gallon)
CPDĀ®ā? liability shall be limited in all events to supplying
s
sufficient product to re-treat and/or repair the specific
area to which the CPDĀ® product has been applied. CPDĀ®
reserves the right to have the true cause of any difficulty
determined by accepted test methods. CPDĀ® shall have no
other liability, including liability for incidental,
consequential or resultant damages, however caused,
whether due to breach of warranty, negligence, or strict
liability.
THIS WARRANTY MAY NOT BE MODIFIED OR
EXTENDED BY REPRESENTATIVES OF CPDĀ®,ITS
DISTRIBUTORS OR DEALERS.
0960-27-1105
|