CIPADITE庐 20
(Hi-Modulus, Injection Resin)
DESCRIPTION MIXING
Cipadite庐 20 is a low viscosity, high strength, high Cipadite庐 20 should be mixed and placed using automatic
modulus, 100% solids epoxy adhesive. This product is injection equipment. Stir each component separately before
designed for use at 10掳C (50掳F) or higher temperatures. using. Take a sample of resin dispensed by the pump
periodically during the injection process. Check the pot
life of the mixed resin to assure proper mixing ratios are
WHERE TO USE
Applications include injection of cracked concrete, maintained by the equipment.
structural bonding and anchor bolt grouting on horizontal
surfaces. LIMITATIONS
? for injection work below 10? (50? see product data
C F),
sheet for Cipadite庐 25
BENEFITS
? areas to receive product must be dry
鈥? low viscosity allows maximum penetration into small
hairline cracks and fractures
COVERAGE
Dependent on crack dimensions and depth.
PROPERTIES (Tested @ 23掳C (74掳F)
Mix Ratio, by Volume . . . . . . . . 2 parts A: 1 part B
STANDARDS
Viscosity (Mixed) . . . . . . . . . . . . . . . . 250-350 cps
ASTM C-881 Type I, Grade 1, Class C.
(ASTM D2393)
Approved for use on all MTQ projects (Ministry of
Solids Content . . . . . . . . . . . . . . . . . . . . . . . . 100%
Transportation).
Pot Life (100g) . . . . . . . . . . . . . . . . . 25-35 minutes
Initial cure . . . . . . . . . . . . . . . . . . . . . . . . . . 6 hours
PACKAGING
Tensile Strength . . . . . . . . . . . . 34 MPa (4,930 psi)
3.79L (1 U.S. gal)- 4.5 kg (10 lbs.)
(ASTM D638) 7 days
18.9L (5 U.S. gal) - 22.5 kg (50 lbs.)
Tensile Elongation . . . . . . . . . . . . . . . . . . . . . 1-5%
(ASTM D638) 7 days
CLEAN UP
Compressive Strength . . . . . . . 69 MPa (10,000 psi)
Clean all equipment with CPD庐 Xylol before epoxy
(ASTM D695) 7 days
hardens. CPD庐 Xylol is a flammable solvent. Read the
Color Cured . . . . . . . . . . . . . . . . . . . . Straw Yellow
Material Safety Data Sheet before using.
The above information is representative of actual STORAGE
production runs. Independent test results may vary from Store in a heated warehouse. Storage at temperatures
the above by approximately 卤 10%. below 4.5掳C (40掳F) may cause the resin to crystallize.
APPLICATION SHELF LIFE
Surface Preparation Two years if kept in original unopened containers under
Cracked surfaces should be dry, clean and free from normal warehouse conditions.
coatings or contaminants which could prevent the proper
adhesion of the crack surface sealer. Where cracks are SAFETY PRECAUTIONS
large, loose material should be removed. Use CIPADITE庐 Consult Material Safety Data Sheet (M.S.D.S.) for
Gel 15 to grout injection ports in place and seal other areas specific instructions. MSDS # 93.
of crack. Cracks that have an active flow of water through
them can not be effectively injected.
0393-04-1105
WARRANTY
The recommendations made and the information herein is
based on our own and independent laboratory experience,
and is believed to be accurate under controlled conditions.
However, no warranty or guarantee of accuracy is made
because we cannot cover every possible application of
product nor anticipate every variation encountered in
weather conditions, job-conditions, methods used and
types of surfaces on which the product is applied. The
users shall make their own tests to determine the suitability
of such products for any particular purpose.
CPD庐 makes no warranties with respect to this product,
expressed or implied, without limitation, the implied
warranties of merchantability or fitness for a particular
purpose.
CPD庐鈥? liability shall be limited in all events to supplying
s
sufficient product to re-treat and/or repair the specific area
to which CPD庐 product has been applied. CPD庐 reserves
the right to have the true cause of any difficulty determined
by accepted test methods. CPD庐 shall have no other
liability, including liability for incidental, consequential or
resultant damages, however caused, whether due to breach
of warranty, negligence, or strict liability.
THIS WARRANTY MAY NOT BE MODIFIED OR
EXTENDED BY REPRESENTATIVES OF CPD庐, ITS
DISTRIBUTORS OR DEALERS.
|