CIPADITE庐 35
High strength epoxy adhesive
The above information is representative of actual
DESCRIPTION
CIPADITE庐 35 is a a two component, 100% solids production runs. Independent test results may vary from
polyamide cure moisture insensitive epoxy adhesive. It has the above by approximately 卤 10 %.
excellent bond strength to concrete, brick, masonry, metal
and wood surfaces. APPLICATION
SURFACE PREPARATION
Prepared concrete substrate should be sound and free from
WHERE TO USE
CIPADITE庐 35 is recommended for bonding fresh concrete dust, loose particles and all foreign contamination. All
to hardened concrete, bonding of precast concrete units and concrete should be chemically cleaned or mechanically
bonding steel plates or other metal sections to concrete. It scarified for best results. New concrete should be cured 30
may also be used for repairing spalled, scaled and cracked days and any surface laitance or curing compound must be
concrete. removed.
Steel surfaces should be free of dirt, grease, oil or rust.
BENEFITS
鈥? 100% solids, zero VOC鈥? s Blast surface using an angular medium such as aluminum
鈥? excellent adhesion properties to concrete and steel oxide or grit to SSPC-SP10 standard, with a minium profile
鈥? extended working time of 2.5 mils. Where sandblasting is not practical, the
鈥? convenient one to one mixing ratio surface should be degreased and mechanically abraded
鈥? color coded to ensure uniform mixing to reveal continuous bright metal.
鈥? moisture insensitive during the cure
鈥? high shear and tensile strength MIXING
鈥? open time of the applied thin film is 4-5 hours @ 23掳C Stir each component separately before combining the
(74掳F) liquids, then combine 1 part (by volume) of Part A with 1
part (by volume) of Part B. Mix with a low speed drill.
PROPERTIES (Tested @ 23"C (74"F) Thoroughly blend material for three minutes minimum,
periodically scraping down sides and bottom of container.
HANDLING PROPERTIES
When thoroughly mixed, product will be a uniform grey in
Mix Ratio, by volume . . . . . . . . . . . .1 Part A: 1 Part B
color.
Viscosity (mixed) . . . . . . . . . . . . . . . . . . . . . . 3000 cps
Mixed Weight (Density) . . . . 1.13kg/litre (9.4lb/US gal) Mortar: Mix Part 鈥? and Part 鈥? as per above
A鈥? B鈥?
Pot-Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1陆 hours instructions. Add 3-4 parts dry silica aggregate by volume.
Initial cure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 hours Add aggregate gradually and mix thoroughly exercising
care not to entrap excessive amounts of air.
Full Cure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 days
Adhesive Application: Apply a thin uniform layer of pre-
CURED PROPERTIES (7 days cured @ R.T./ 50% R.H.)
mixed CIPADITE庐 35 with brush, or roller. Avoid forming
Tensile Strength . . . . . . . . . 22-25 MPa (3200-4000 psi)
pools or puddles. Place fresh concrete or topping while
(ASTM D638) CIPADITE庐 35 is still tacky.
Tensile Elongation . . . . . . . . . . . . . . . . . . . . . . . . . 8 %
(ASTM D638) Patching Application: Sawcut perimeter of spall and
prime with mixed neat CIPADITE庐 35. Surface should be
Compressive Strength . . . . 40-62 MPa (5800-9000 psi)
dry and clean. Apply mortar by trowel.
(ASTM D695)
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . grey
0390-04-1105
resultant damages, however caused, whether due to breach
LIMITATIONS
CIPADITE庐 35 is not recommended for: of warranty, negligence, or strict liability.
? applications where ambient temperature are below 10?C
(50?F) THIS WARRANTY MAY NOT BE MODIFIED OR
? repairs applied underwater EXTENDED BY REPRESENTATIVES OF CPD庐, ITS
DISTRIBUTORS OR DEALERS.
COVERAGE
2-3m虏/L (80-120ft虏/U.S. gal) depending on surface texture.
PACKAGING
Available in:
7.58L (2 U.S. gallon)
37.9L (10 U.S. gallon)
CLEAN UP
Clean all equipment with CPD庐 Xylol before epoxy
hardens. CPD庐 Xylol is flammable solvent. Read the
M.S.D.S. before using.
STORAGE
Store in a heated warehouse. Storage at temperatures below
4.5掳C (40掳F) may cause the resin to crystallize.
SHELF LIFE
Two years from date of manufacture if kept in original
unopened containers under normal warehouse conditions.
SAFETY PRECAUTIONS
Consult Material Safety Data Sheet (M.S.D.S.) for specific
instructions. MSDS # 46 + 49
WARRANTY
The recommendations made and the information herein is
based on our own and independent laboratory experience,
and is believed to be accurate under controlled conditions.
However, no warranty or guarantee of accuracy is made
because we cannot cover every possible application of
product nor anticipate every variation encountered in
weather conditions, job-conditions, methods used and types
of surfaces on which the product is applied. The users shall
make their own tests to determine the suitability of such
products for any particular purpose.
CPD庐 makes no warranties with respect to this product,
expressed or implied, without limitation, the implied
warranties of merchantability or fitness for a particular
purpose.
CPD庐鈥? liability shall be limited in all events to supplying
s
sufficient product to re-treat and/or repair the specific area
to which CPD庐 product has been applied. CPD庐 reserves
the right to have the true cause of any difficulty determined
by accepted test methods. CPD庐 shall have no other
liability, including liability for incidental, consequential or
|