CIPADECK® T-Coat
General Purpose Epoxy Topcoat
DESCRIPTION APPLICATION
CIPADECK® T-Coat is an economical high solids two MIXING
component epoxy coating. It is primarily designed to be The mixing equipment used to mix the coating must be
used as a tie coat over the CIPADECK® waterproofing clean and free of any contaminants that may be present
systems. It provides superior abrasion resistance, in the equipment from previously used products. Mix
appearance and cleanability for the CIPADECK® component A first to eliminate the possibility of
waterproofing systems. settlement. Pour all of the liquid from Part A and Part
B into the mixing equipment. A � Jiffy Mixer’or a mud
mixer blade on a slow speed drill is the preferred method
WHERE TO USE
CIPADECK® T-Coat is recommended for use as a non- of mixing. Mix the blended components for a minimum
slip tie-coat for parking garages, balconies, plaza decks, of 2 minutes.
ramps and walkways or areas subjected to heavy
vehicular traffic. APPLICATION
Pour a workable amount of the mixed coating on to the
CIPADECK® waterproof coating and spread the
BENEFITS
� easy to apply material evenly with a flat squeegee. Using a lint free
� high solids, VOC compliant 5mm nap roller (designed for epoxy and urethane), back
� good flexibility, abrasion and impact resistance roll the applied material to provide an even coat. Allow
� good color stability and weather resistance to cure thoroughly before exposing to traffic.
®
� cures down to 5° C (40° F) CIPADECK T-Coat can be sprayed using standard
� available in standard colors technique.
Handling Properties COVERAGE
4.9-7.8m²/litre (200-320 ft²/U.S. gallon) (5-8 mils dft)
Mix Ratio, by volume . . . . . . . . . 5 parts A: 1 part B
Viscosity (Mixed) @ 23°C (74°F) . . . . . . . . 2000 cps
PACKAGING
Solids Content . . . . . . . . . . . . . . . . 80 % (by weight) CIPADECK® T-Coat is packaged in:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 % (by volume) 3.79 litre/1 U.S. gal. units
Mixed Weight (Density) 1.3kg/litre (10.88 lb/US gal) 18.9 litre/ 5 U.S. gal. units
Pot Life @ 23°C (74°F) . . . . . . . . . . . . . . . 4-5 hours
CLEAN UP
Application Temperature . . . . 5°C-30°C (40°F-86°F)
Clean all equipment and installation tools immediately
Foot Traffic @ 23°C (74°F) . . . . . . . . . . . . 16 hours
with CPD® Xylol . Read the M.S.D.S. for this product
Vehicular Traffic @ 23°C (74°F) . . . . . . . . 36 hours
prior to use.
Full Cure and Maximum Resistance . . . . . . . . 7 days
STORAGE
Store in a heated warehouse. Do not freeze.
DATA - Cured Film
Flexibility . . . . . . . 180° @ 0.015" over 3/4" mandril
SHELF LIFE
Impact Resistance . . . . . . . . . . . . . . . . pass 160 in/Ib
Three years from the date of manufacture if kept in
(ASTM D2794) original unopened containers under normal heated
Abrasion Resistance (ASTM4060) . . . . . 100 mg loss warehouse conditions.
Taber Abrasion, C-17 Wheel, 1000 cycles
SAFETY PRECAUTIONS
Consult Material Safety Data Sheet (M.S.D.S.) for
The above information is representative of actual
specific instructions. M.S.D.S. #288 + 288A
production runs. Independent test results may vary from
the above by approximately ±10%.
0960-23-1105
WARRANTY
The recommendations made and the information herein is
based on our own and independent laboratory experience,
and is believed to be accurate under controlled conditions.
However, no warranty or guarantee of accuracy is made
because we cannot cover every possible application of
product nor anticipate every variation encountered in
weather conditions, job conditions, methods used and
types of surfaces on which the product is applied. The
users shall make their own tests to determine the
suitability of such products for any particular purpose.
CPD® makes no warranties with respect to this product,
expressed or implied, including, without limitation, the
implied warranties of merchantability or fitness for a
particular purpose.
CPD®� liability shall be limited in all events to supplying
s
sufficient product to re-treat and/or repair the specific
area to which the CPD® product has been applied. CPD®
reserves the right to have the true cause of any difficulty
determined by accepted test methods. CPD® shall have no
other liability, including liability for incidental,
consequential or resultant damages, however caused,
whether due to breach of warranty, negligence, or strict
liability.
THIS WARRANTY MAY NOT BE MODIFIED OR
EXTENDED BY REPRESENTATIVES OF CPD®,ITS
DISTRIBUTORS OR DEALERS.
|