CIPADECKĀ® BL SYSTEM
Balcony Deck Waterproofing System
DESCRIPTION PROPERTIES
CIPADECKĀ® BL System is an economical multi coat cold CIPADECKĀ® CIPADECKĀ®
applied pedestrian waterproofing system. It consists of a Membrane 60LT T-Coat
solvent based low temperature cure two component Handling Properties (tested @ 23Ā° C (74Ā° F)
polyurethane membrane, CIPADECKĀ® Membrane 60LT, and Mix Ratio, by volume, A/B 10/1 5/1
a flexible topcoat, CIPADECKĀ® T-Coat. Together, they
provide an attractive durable monolithic waterproofing Viscosity (Mixed), cps 2000 2000
system.
Mixed Weight (Density),
WHERE TO USE kg/litre (Ib/ gal.) 1.21 (10.1)1.3
(10.88)
CIPADECKĀ® BL System is a cold applied deck coating
system, primarily designed for waterproofing balcony decks,
Solids Content,
pedestrian walkways, plywood decks and plaza decks.
by volume 80% 70%
by weight 86% 80%
BENEFITS
ā? high solids, contains no isocyanate
Pot Life 1-2 hours 4-5 hours
ā? impervious to water and/or chloride penetration
Set Time 16 hours 12 hours
ā? moisture insensitive during the application and
Full Cure 7 days 7 days
throughout the cure (not affected by humidity)
ā? long pot life and easy to apply
DATA - Cured Film (7 days Cured @ RT/ 50% RH)
ā? good color stability and weather resistance
Elongation % 400-450 100
ā? good abrasion resistance (ASTM D 412)
ā? tough, resilient and flexible over a wide temperature
range Tensile Strength, MPa (psi) 4-5 (580-725) 11
ā? CIPADECKĀ® Membrane 60LT retains its integrity even (1600)
if substrate movement causes hairline cracks of up (ASTM D 412)
to1.6mm (1/16")
ā? available in a wide range of standard colors Hardness (Shore A) 50 85
ASTM D2240
APPLICATION
SURFACE PREPARATION Peel Adhesion, pli N/A 70
New concrete must be cured for a minimum of 28 days before (ASTM C794)
applying CIPADECKĀ® BL System. The surface should be
primed using CIPADITEĀ® Primer E-40. The substrate must Abrasion Resistance, mg loss 20 100
be above 10Ā°C (50Ā°F) and must be free of all dirt, waxes, (ASTM D4060, Taber, CS-17, 1000 cycles)
previously applied coatings, oil, grease, laitance and any
Chemical Resistance
foreign matter that may interfere with the bond of the coating
no effect from motor oils, gasoline, anti-freeze, alkalis,
to the prepared substrate. Cracks and surface defects should
salts and common household chemicals.
be repaired prior to the application of the coating. All
concrete and steel surfaces to be treated should be shot blast
The above information is representative of actual
or mechanically cleaned to provide a clean tooth for the
production runs. Independent test results may vary from the
coating application.
above by approximately Ā± 10%.
DETAILING
CIPADECKĀ® Membrane 60LT must be extended a
Joints or cracks should be repaired prior to application of
CIPADECKĀ® BL System. Cracks and cold joints less than minimum distance of 50 mm (2") on either side of all sealed
cracks, cold joints and control joints to yield a total film
1.6mm (1/16") wide should be coated over with the
CIPADECKĀ® Membrane 60LT. All cracks and joints greater thickness of 20-30 mils dry.
than 1.6mm (1/16") wide must be routed and sealed with an
approved polyurethane sealant.
0960-24-1105
ā? CIPADECKĀ® BL System may discolor slightly upon
MIXING
The mixing equipment used must be clean and free of exposure to direct sunlight over an extended period of
any contaminants that may be present in the equipment time
from previously used products. Mix component A first to
eliminate the possibility of settlement. Pour all of the COVERAGE
CIPADITEĀ® PRIMER E-40 (Optional):
liquid from Part A and Part B into the mixing container.
Aā? Jiffy Mixerā? or a mud mixer blade on a slow speed 4.0-7.9mĀ²/litre (163-320ftĀ²/US gal) @ 2-4 mils dft
drill is the preferred method of mixing. Mix the blended
CIPADECKĀ® Membrane 60LT:
components for a minimum of 3 minutes.
1.6 mĀ²/litre (65 ftĀ²/US gal)@ 20 mils dft
APPLICATION
CIPADECKĀ® T-COAT:
Primer Installation:
3.4-5.6mĀ²/litre (140-228ftĀ²/US gal) @ 5-8 mils dft
Pour a workable amount of the mixed primer onto the
prepared substrate and spread the material evenly with a
NOTE: The recommended mil thickness of this system will
flat squeegee @ 2-4 mils dry film thickness. Using a lint
vary depending on service conditions, substrate profile and
free 5mm nap roller (designed for epoxy and urethane),
other environmental factors.
back roll the applied material to provide an even coat.
Care should be taken not to over roll the material as air
may become entrapped in the coating. Avoid puddling of PACKAGING
CIPADITEĀ® Primer E-40:
material. Allow to cure for 2-3 hours @ 23Ā°C prior to
the application of the CIPADECKĀ® waterproofing 7.58 litre/2 U.S. gal. unit
37.9 litre/10 U.S. gal. unit
system.
CIPADECKĀ® Membrane 60LT:
Membrane Installation:
Pour a workable amount of the mixed CIPADECKĀ® 3.79 litre/ 1 U.S. gal. unit
41.59 litre/11 U.S. gal. unit
Membrane 60LT onto the prepared substrate and spread
it evenly over the surface with a notched squeegee at 20-
CIPADECKĀ® T-COAT:
30 mils dry film thickness. Using a lint free 5 mm nap
3.79 litre/1 U.S. gal. unit
roller,(designed for epoxy and urethane) back roll the
18.9 litre/ 5 U.S. gal. unit
applied material to provide an even coat. Allow the
coating to dry overnight. (If CIPADITEĀ® PRIMER E-40
is used, CIPADECKĀ® Membrane 60LT should be CLEAN UP
Clean all tools and equipment with Xylene Solvent prior to
applied within 3 hours of primer application.)
material set.
Topcoat Installation:
CIPADECKĀ® T-Coat should be applied like paint over STORAGE
the cured CIPADECKĀ® Membrane 60LT at 5-8 mils Must be stored in a dry heated warehouse. Do not allow to
freeze in storage or transport as base resin may crystalize.
film thickness using a lint free 5mm nap roller .
Broadcast silica aggregate (50 mesh) lightly into the wet
coat and back roll to provide a non-slip finish. Allow to SHELF LIFE
One year if stored under normal heated warehouse conditions
cure overnight.
in original unopened containers.
LIMITATIONS
ā? do not apply over damp surface, unless CIPADITEĀ® SAFETY PRECAUTIONS
Consult Material Safety Data Sheet (M.S.D.S.) for specific
PRIMER E-40 is used
instructions. CIPADECKĀ® Membrane 60LT MSDS # 232
ā? concrete temperature must be a minimum of 10Ā°C
+ 232a, CIPADECKĀ® T-Coat MSDS #288 + 288a.
(50Ā°F) during application. (An induction time of 30
minutes at 10Ā°C (50Ā°F) will be required.)
ā? do not use for interior applications unless adequate
ventilation is used
WARRANTY
The recommendations made and the information herein is
based on our own and independent laboratory experience,
and is believed to be accurate under controlled conditions.
However, no warranty or guarantee of accuracy is made
because we cannot cover every possible application of
product nor anticipate every variation encountered in
weather conditions, job conditions, methods used and
types of surfaces on which the product is applied. The
users shall make their own tests to determine the
suitability of such products for any particular use.
CPDĀ® makes no warranties with respect to this product,
expressed or implied, without limitation, the implied
warranties of merchantability or fitness for a particular
purpose.
CPDĀ®ā? liability shall be limited in all events to supplying
s
sufficient product to re-treat and/or repair the specific
area to which CPDĀ® product has been applied. CPDĀ®
reserves the right to have the true cause of any difficulty
determined by accepted test methods. CPDĀ® shall have no
other liability for incidental, consequential or resultant
damages, however caused, whether due to breach of
warranty, negligence, or strict liability.
THIS WARRANTY MAY NOT BE MODIFIED OR
EXTENDED BY REPRESENTATIVES OF CPDĀ®, ITS
DISTRIBUTORS OR DEALERS.
0960-25-1105
|