CIPADAM庐 E-13
Load Bearing Control Joint Filler
The above information is representative of actual
DESCRIPTION
CIPADAM庐 E-13 is a 100% solids, two component, self- production runs. Independent test results may vary from
leveling flexible epoxy urethane joint sealant for load the above by approximately 卤 10%.
bearing saw cut or preformed control joints.
APPLICATION
WHERE TO USE SURFACE PREPARATION
CIPADAM庐 E-13 is recommended for use as a joint filler Joints to receive CIPADAM庐 E-13 must be clean and dry.
for interior horizontal sawcut or preformed control joints. Remove any dirt, dust, grease, oil or other foreign
It is typically used in facilities such as manufacturing areas, contaminates from joints. Both sides of joints should be
warehouses and loading docks where joints are subject to covered with masking tape. Use a bond breaker in the
dynamic loading and impact. CIPADAM庐 E-13 bottom of the joint such as polyethylene film or tape.
is also suitable for repairing interior concrete slabs that
have cracked due to settlement or shrinkage. PRIMER
No primer is required for dry joints. In the event the joints
are not dry, consult your CPD庐 Technical Representative
BENEFITS
鈥? 100% solids, low odor, zero VOC鈥? s for primer recommendations.
鈥? protects joint edges yet allows sufficient flexibility for
interior slabs MIXING
鈥? fast setting to minimize traffic disruption Pre-mix each component separately before combining.
鈥? excellent self-leveling and flow properties Mix one part (by volume) of Part 鈥淎鈥? and one part (by
鈥? color coded; comparable viscosities of Part A&B volume) of Part 鈥淏鈥?. Mix thoroughly for 2-3 minutes until
鈥? convenient one to one mixing ratio for ease of application a uniform grey color is achieved. Exercise care not to
entrap air while mixing.
PROPERTIES: Wet Properties: (Measured @ 23掳C (74掳F):
PLACING
Mix Ratio, by volume . . . . . . . . . . . . . . . 1 part A : 1 part B
Mixed product can be placed with a conventional caulking
Viscosity (Mixed) . . . . . . . . . . . . . . . . . . . . . . . . . 3000 cps
gun or poured from the mixing container or a disposable
Solids Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100%
metal or plastic container. Two passes are generally
Mixed Weight (Density) . . 1.05 kg/litre (8.77 lb/US gallon)
required to bring the sealant up flush with the floor surface
Pot Life (working time) . . . . . . . . . . . . . . . . . . . . 13 minutes
as a neat, even joint, free from 鈥渄ishing鈥?. The second pour
Gel Time (200 gm mass) . . . . . . . . . . . . . . . . . . . 16 minutes
must be made before the initial pour sets. NOTE: The joint
Cut Time . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 to 24 Hours
must be completely filled with CIPADAM庐 E-13 from the
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . grey
bottom up for proper performance.
Cured Properties (7 days cured @ 23掳C, 50 RH)
Shore Hardness . . . . . . . . . . . . . . . . . . . . . . . . . 85A (40D) LIMITATIONS
鈥? use only for interior horizontal joints
(ASTM D2240)
鈥? do not use as an expansion joint filler or for applications
Tensile Strength . . . . . . . . . . . . . . . . . . . 10 MPa (1500 psi)
involving continuous immersion
(ASTM D638)
鈥? CIPADAM庐 E-13 is not designed for use in areas
Tensile Elongation . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 %
subjected to chemical exposure
(ASTM D638)
鈥? concrete temperature must be a minimum of 10掳C
Abrasion Resistance (ASTM D4060) . . . . . . . . . 90mg loss
(50掳F) during application
Taber Abrasion, C-17 Wheel, 1000 cycles
鈥? concrete must be a minimum of 28 days old prior to
Pull Out Tensile Adhesion to concrete . . 2.4 MPa.(350 psi)
sealant installation
(ASTM D4541) (concrete failure)
鈥? CIPADAM庐 E-13 may discolor in areas exposed to
Water absorption . . . . . . . . . . . . . . . . . . . 0.5 % (by weight)
constant sunlight
(ASTM D413)
0792-01-1105
CPD庐鈥? liability shall be limited in all events to supplying
s
COVERAGE
*For a 4.5L (1.2 U.S. Gallons) of mixed product. sufficient product to re-treat and/or repair the specific area
to which CPD庐 product has been applied. CPD庐 reserves
WIDTH DEPTH LENGTH
the right to have the true cause of any difficulty determined
by accepted test methods. CPD庐 shall have no other
3mm (c鈥?) 19mm (戮鈥?) 71m (237ft)
liability for incidental, consequential or resultant damages,
25.4mm (1") 53m (178ft)
however caused, whether due to breach of warranty,
38mm (1陆鈥?) 35m (118ft)
negligence, or strict liability.
4.5mm (3/16") 19mm (戮鈥?) 48m (151ft)
25.4mm (1") 36m (118ft) THIS WARRANTY MAY NOT BE MODIFIED OR
38mm (1陆鈥?) 23m (78ft) EXTENDED BY REPRESENTATIVES OF CPD庐, ITS
DISTRIBUTORS OR DEALERS.
6.4mm (录鈥?) 19mm (戮鈥?) 36m (118ft)
25.4mm (1") 27m (87ft)
38mm (1陆鈥?) 18m (59ft)
PACKAGING
4.5 L (1.2 U.S. gal) unit - 5 kg (11 lb)
CLEAN UP
Clean all tools and equipment with Xylene Solvent prior to
material set.
STORAGE
Must be stored in a dry heated warehouse. Do not allow to
freeze in storage or transport as base resin may crystalize.
SHELF LIFE
Two years if stored under normal heated warehouse
conditions in original unopened containers.
SAFETY PRECAUTIONS
Consult Material Safety Data Sheet (M.S.D.S.) for specific
instructions. MSDS#300 + 300a
WARRANTY
The recommendations made and the information herein is
based on our own and independent laboratory experience,
and is believed to be accurate under controlled conditions.
However, no warranty or guarantee of accuracy is made
because we cannot cover every possible application of
product nor anticipate every variation encountered in
weather conditions, job conditions, methods used and types
of surfaces on which the product is applied. The users shall
make their own tests to determine the suitability of such
products for any particular use.
CPD庐 makes no warranties with respect to this product,
expressed or implied, without limitation, the implied
warranties of merchantability or fitness for a particular
purpose.
|