MATERIAL SAFETY DATA SHEET
GENERIC MSDS ACRYLIC LAQUER IN AEROSOL CANS PAGE: 1
PRODUCT NAME: GENERIC MSDS ACRYLIC LACQUER IN AEROSOL CANS HMIS CODES: H F R P
FORMULA KEY: CUSTOM AEROSOL PRO 230I
===================== SECTION I - MANUFACTURER IDENTIFICATION =====================
MANUFACTURER'S NAME: Custom Aerosol Products, Inc.
ADDRESS : 10010 Rearwin Ln
McKinney, TX 75071
EMERGENCY PHONE : 1-800-451-8346 DATE PRINTED : 3/1/2004
INFORMATION PHONE : 1-972-346-2700 NAME OF PREPARER : Preston Staley
============== SECTION II - HAZARDOUS INGREDIENTS/SARA III INFORMATION =============
VAPOR PRESSURE WEIGHT
REPORTABLE COMPONENTS CAS NUMBER mm Hg @ TEMP
PERCENT
----------------------------------------------------------------------------------------------------
ACETONE 67-64-1 181.7 20 C
41.05
OSHA PEL: 750 PPM
ACGIH TLV: 500 PPM
* XYLOL 1330-20-7 8 68 DEG F
12.05
OSHA PEL/TWA IS 100PPM
ACGIH TLV/TWA IS 100 PPM
ACGIH TLV/STEL IS 100 PPM
ISOBUTANE 75-28-5 55 25 DEG C
11.05
OSHA PEL: 800 PPM
PROPANE 74-98-6 110 70 F
5.2
OSHA PEL: 1000 PPM
ACGIH TLV: 1000 PPM
* ## ETHYL BENZENE 100-41-4 7.1 20 DEG C
2.95
OSHA PEL: 100 PPM
ACGIH TLV: 125 PPM
1-METHOXY 2-PROPYL ACETATE 108-65-6 4.9 20 DEG C
1.85
* EB ETHYLENE GLYCOL BUTYL ETHER 111-76-2 88 25 DEG C
1.5
OSHA PEL: 50 PPM
MINERAL SPIRITS 8052-41-3 4.9 100 F
.8
OSHA PEL: 100 PPM
ACGIH TLV: 100 PPM
GLYCOL ETHER PM 107-98-2 88 25 DEG C
.75
OSHA PEL: 50 PPM
METHOXY-2-PROPANOL 107-98-2 8.4 25 C
.7
OSHA PEL: 100 PPM
ACGIH TLV: 100 PPM
MATERIAL SAFETY DATA SHEET
GENERIC MSDS ACRYLIC LAQUER IN AEROSOL CANS PAGE: 2
METHYL METHACRYLATE 80-62-6 29 68 DEG.F
.25
OSHA PEL: 100 PPM
ACGIH TLV: 125 PPM
N-BUTYL ACETATE 123-86-4 10 68 DEG F
.15
OSHA PEL: 150 PPM
ACGIH TLV: 150 PPM
* Indicates toxic chemical(s) subject to the reporting requirements of section 313 of Title III and
of 40 CFR 372.
## This product has been reported to cause cancer in laboratory animals. The relevance of these
findings to humans is uncertain, but appropriate safeguards should be employed to reduce or
eliminate exposure.
================= SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS ================
BOILING RANGE: 133 DEG F - 355 F WEIGHT PER GALLON: 6.52 lb/gl
VAPOR DENSITY: HEAVIER THAN AIR EVAPORATION RATE: SLOWER THAN ETHER
COATING V.O.C.: 4.067 lb/gl MATERIAL V.O.C.: 2.432 lb/gl
APPEARANCE AND ODOR: Viscous liquid with an odor characteristic of the solvents
listed in Section II.
=================== SECTION IV - FIRE AND EXPLOSION HAZARD DATA ==================
FLASH POINT: 48 DEG.F METHOD USED: TCC
FLAMMABLE LIMITS IN AIR BY VOLUME- LOWER: .8 UPPER: 13.1
EXTINGUISHING MEDIA: Use National Fire Protection Association (NFPA) Class B extin
chemical, or universal aqueous film forming foam) designed to extinquish NFPA Flammable liquid
fires.
SPECIAL FIREFIGHTING PROCEDURES
Water spray may be ineffective. Water spray may be used to cool closed containers to prevent
pressure build-up andpossible autoignition or explosion when exposed to extreme heat. If water is
used, fog nozzles are preferrable. Firefighters should wear self contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARDS
Contents under pressure. Do not use or store near sources of heat, sparks or open flame. Keep away
from any source of heat such as sunlight, heaters or stoves that could cause the container to burst.
Do not puncture or incinerate. Do not crush or place in a garbage compactor. Do not store above
120 degrees F. Aerosol containers may explode when exposed to extreme heat. Product vapors are
heavier than air and may travel a long distance to a source of ignition and flash back.
=========================== SECTION V - REACTIVITY DATA ===========================
STABILITY: Stable
CONDITIONS TO AVOID
Avoid contact with strong alkalis, strong mineral acids, or strong oxidizing agents. Avoid high
temperatures, direct heating.
HAZARDOUS DECOMPOSITION OR BYPRODUCTS
May produce hazardous decomposition products when heated. Welding, brazing, or flame-cutting on
surfaces coated with this product may produce fumes including: Carbon Monoxide or Carbon Dioxide.
MATERIAL SAFETY DATA SHEET
GENERIC MSDS ACRYLIC LAQUER IN AEROSOL CANS PAGE: 3
HAZARDOUS POLYMERIZATION: Not expected to occur.
====================== SECTION VI - HEALTH HAZARD DATA ==========================
INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Vapor and spray mist may be harmful if inhaled. Vapor irritates eyes, nose, and throat. Repeated
exposure to high vapor concentrations may cause irritation of the respiratory system and permanent
brain and nervous system damage. Intentional misuse by deliberately inhaling the contents can be
harmful or fatal.
SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Eye contact: causes eye irritation. May experience itching, burning sensation and visual
disturbances.
SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
May cause moderate skin irritation. May be harmful if absorbed through the skin. Dryness, itching,
cracking, burning, redness, and swelling are conditions associated with excessive skin contact.
INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Harmful or fatal if swallowed.
HEALTH HAZARDS (ACUTE AND CHRONIC)
Avoid long term and repeated contact.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE
Not applicable.
EMERGENCY AND FIRST AID PROCEDURES
INGESTION: If swallowed, have conscious patient drink several glasses of water. Induce vomiting if
conscious. Keep head below hips to prevent aspiration of liquid into lungs. Get medical help
immediately. EYES: In case of eye contact, flush eyes immediately with plenty of water for at least
15 minutes. SKIN: In case of skin contact, remove promptly by wiping, followed by waterless hand
cleaner and soap and water. INHALATION: If affected by inhalation of vapor or spray mist, remove to
fresh air. Apply artificial respiration and other supportive measures as required. Get medical
attention.
============== SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE ===============
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Provide maximum ventilation. Only personnel equipped with proper respiratory and skin and eye
protection should be permitted in the area. Remove all sources of ignition. Take up spilled
material with sawdust, vermiculite, or other absorbent material and place into containers for
disposal.
WASTE DISPOSAL METHOD
Waste material must be disposed of in accordance with Federal, State, and Local environmental
control regulations. Empty containers should be recycled or disposed of through an approved Waste
Management Facility.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
Do not store above 120 deg. F. Store large quantities in buildings designed and protected for
storage of NFPA Flammable liquids.
MATERIAL SAFETY DATA SHEET
GENERIC MSDS ACRYLIC LAQUER IN AEROSOL CANS PAGE: 4
OTHER PRECAUTIONS
If this material is part of a multiple component coating system, read the MSDS for the other
component or components before blending as the resulting mixture may have the hazards of all of its
parts. Containers should be grounded when pouring. Avoid free fall of liquids in excess of a few
inchs. Containers of this material may be hazardous when emptied since they retain residues. Do
not cut, puncture, or weld on or near container.
======================== SECTION VIII - CONTROL MEASURES =========================
RESPIRATORY PROTECTION
Overexposure to vapors may be prevented by ensuring ventilation controls, vapor exhaust or fresh air
entry. If TLV of any component is exceeded, use an appropriate NIOSH/MSHA approved respirator.
Follow respirator manufacturers directions for respirator use.
VENTILATION
Provide sufficient mechanical and/or local exhaust ventilation to keep the concentration of
ingredients listed in Section II below the lowest exposure limits.
PROTECTIVE GLOVES
Impermeable chemical handling gloves for skin protection.
EYE PROTECTION
Use chemical safety glasses, goggles, and faceshields for eye protection.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT
Use impermeable aprons and protective clothing whenever possible to prevent skin contact. The use
of head caps whenever possible is strongly recommended. Clean or discard contaminated clothing and
shoes.
WORK/HYGIENIC PRACTICES
Eye washes and safety showers in the workplace are recommended.
============================ SECTION IX - DISCLAIMER =============================
The information and recommendations contained herein are believed to be accurate at the time of
preparation or obtained from sources believed to be generally reliable. Custom Aerosol Products
will not be held liable for claims relating to any party's use of or reliance on information
contained herein, regardless of whether it is claimed the information is inaccurate.
|