Material Safety Data Sheet
Page 1 of 6 Issue date: September 2004
M BOND AE-10
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Davidson Measurement Pty. Ltd
ACN: 005 031 961 ABN: 29 005 031 961
Phone: 03 9580 4366
Fax: 03 9580 6499
Email: info@davidson.com.au
Web: www.davidson.com.au
Address: 1-3 Lakewood Boulevard,
Braeside, Victoria, 3195.
Product Name: M BOND AE-10
Manufacturer's Product Code: MGM002F
Use: Two component, 100 %-solids epoxy system for general purpose stress analysis.
2. HAZARDS IDENTIFICATION
HAZARDOUS ACCORDING TO EU CRITERIA
Hazard Category: Harmful (Xn), Corrosive (C)
Hazard Classification: HAZARDOUS SUBSTANCE, DANGEROUS GOODS.
RISK PHRASES
R21 Harmful in contact with skin.
R34 Causes burns.
R43 May cause sensitisation by skin contact.
SAFETY PHRASES
S1/2 Keep locked up and out of reach of children.
S26 In case of contact with eyes, rinse immediately with plenty of water and contact a doctor or Poisons Information
Centre.
S36/37/39 Wear suitable protective clothing, gloves and eye/face protection.
S45 In case of accident or if you feel unwell, contact a doctor or Poisons Information Centre immediately and show
this container or label.
R52 Harmful to aquatic organisms.
R53 May cause long term adverse effects in the aquatic environment.
Poison Schedule: S5 [Aust]
This product is a Scheduled (S5) Poison and must be stored, handled and used according to the appropriate regulations.
Warning Statement:
This product is considered to be hazardous by all routes of exposure. European Union information suggests that this
product will be corrosive to eyes, skin and if swallowed. It is also likely to cause sensitisation by skin contact.
3. COMPOSITION / INFORMATION ON INGREDIENTS
SUBSTANCE NAME Proportion CAS Number
TRIETHYLENETETRAMINE > 98 % 112-24-3
All other ingredients determined not to be hazardous according to the EU criteria.
4. FIRST AID MEASURES
Swallowed:
If swallowed, DO NOT induce vomiting. If victim is conscious give water to drink. Immediately transport to hospital or
doctor.
Material Safety Data Sheet
Page 2 of 6 Issue date: September 2004
M BOND AE-10
4. FIRST AID MEASURES (Continued)
Eye:
If material is splashed into eyes, flush with plenty of water for at least 15 minutes, ensuring eye lids are held open.
Urgently transport to hospital or doctor.
Skin:
If material is splashed onto the skin, remove any contaminated clothing and wash skin thoroughly with water and soap.
If irritation persists transport to hospital or doctor.
Inhaled:
Move victim to fresh air. Apply resuscitation if victim is not breathing.
First Aid Facilities:
Eye wash fountain, safety shower and normal wash room facilities.
Advice to Doctor:
Treat symptomatically.
In case of poisoning, contact Poisons Information Centre
In Australia call Tel: 131126
In New Zealand Tel: 034747000
5. FIRE-FIGHTING MEASURES
Fire/Explosion Hazard
CAUTION: Use of water spray when fighting fire may be inefficient.
SUITABLE EXTINGUISHING MEDIA: Use dry chemical, carbon dioxide, foam or water fog.
UNUSUAL FIRE AND EXPLOSION HAZARDS: If tanks, drums or containers of this material are heated, they may
rupture and project corrosive liquids over a wide area.
HAZARDS FROM COMBUSTION PRODUCTS: Under fire conditions, toxic and corrosive fumes are emitted. On
combustion or on thermal decomposition (pyrolysis), there will be a release of oxides of carbon and oxides of nitrogen.
PRECAUTIONS FOR FIRE FIGHTERS AND SPECIAL PROTECTIVE EQUIPMENT: Self-contained
breathing apparatus (SCBA) required for fire -fighting personnel. If possible to do so safely, shut off fuel to fire. Use
water spray to spray to cool fire-exposed surfaces and to protect personnel.
Hazchem Code: 2X [Aust]
Flammability:
This material is a COMBUSTIBLE liquid.
Flash Point: 118掳C
Flammability Limits: LEL: 1.1% UEL: >6.4% at 185掳C
6. ACCIDENTAL RELEASE MEASURES
Emergency Procedures:
Combustible liquid. Avoid all sources of ignition. Keep unnecessary people away; Isolate hazard area and deny entry.
Ventilate area. Wear suitable protective equipment as outlined under personal protection in this MSDS.
Methods and Materials for Containment and Clean Up Procedures:
Ventilate area. Flood with water to polymerize cyanoacrylate adhesive and to control product vapors. Soak up with an
inert absorbent or scrape up cured product. Place into suitably labeled drum(s) for later disposal.
Emergency information(Transport):
Dangerous Goods - Initial Emergency Response Guide (SAA/SNZ HB76:1997)
For TOXIC AND/OR CORROSIVE Guide No: 37
Material Safety Data Sheet
Page 3 of 6 Issue date: September 2004
M BOND AE-10
7. HANDLING AND STORAGE
Precautions for Safe Handling:
Do not get in eyes. Avoid direct or prolonged contact with skin. Provide adequate ventilation.
Conditions for Safe Storage:
Keep containers tightly closed, when not using the product. Store in original packages as approved* by manufacturer.
Store in an area that is dry and well-ventilation away from ignition sources. Store below 278 C. The floor of the depot
should be impermeable. Store away from strong alkalis, acids and oxidizing agents. For further information please refer
to the Engineering Controls of this MSDS.
M BOND AE-10 is a Combustible (C1) Liquid and must be stored, handled and used according to the requirements of
,
AS 1940 [Aust]
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Exposure Standards
No exposure have been assigned by the [NOHSC] for this product or any of the ingredients.
Engineering Controls
Corrosive liquid. Maintain adequate ventilation at all times. In most circumstances natural ventilation systems are
adequate.
Personal Protecti on Equipment
GLOVES: Not normally required, however, if product has spilt, or package is broken, then the use of neoprene gloves
is recommended.
EYES: Chemical goggles or spectacles with side shields to protect eyes.
RESPIRATORY PROTECTION: Avoid breathing of vapours. Select and use respirators in accordance with AS/NZS
1715/1716. The use of an acid gas vapour respirator with replaceable filters is recommended. Filter capacity and
respirator type depends on exposure levels and type of contaminant. If entering spaces where the airborne concentration
of a contaminant is unknown then the use of a Self-contained breathing apparatus (SCBA) with positive pressure air
supply complying with AS/NZS 1715 / 1716, or any other acceptable International Standard is recommended.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Light, straw colored liquid; amine odor.
Boiling Point: 250掳C
Vapour Pressure: <1 mmHg @ 20掳C
Specific Gravity: 0.973 - 0.981
Flash Point: 118掳C
Flammability Limits: LEL: 1.1% UEL: >6.4% at 185掳C
Solubility in Water: Mixes completely
Other Properties
Vapor Density (Air = 1): 5.04
10. STABILITY AND REACTIVITY
CHEMICAL STABILITY:
Stable under normal conditions of use.
CONDITIONS TO AVOID:
Can autoignite in air at approximately 2958 C
HAZARDOUS DECOMPOSITION PRODUCTS:
Emits oxides of carbon and oxides of nitrogen when heated to decomposition.
Material Safety Data Sheet
Page 4 of 6 Issue date: September 2004
M BOND AE-10
10. STABILITY AND REACTIVITY (Continued)
INCOMPATIBLE MATERIALS:
Acid, oxidizing material, halogenated organic compounds, aldehydes, ketones and acrylates. Mixture with these
materials will result in a temperature and/or pressure increase.
HAZARDOUS REACTIONS:
Will not occur.
11. TOXICOLOGICAL INFORMATION
ACUTE HEALTH EFFECTS
Swallowed:
Will cause burns to the mouth, mucous membranes, throat, oesophagus and stomach. If sufficient quantities are ingested
(swallowed) death may occur.
Eye:
Will cause burns to the eyes with effects including: Pain, tearing, corneal opacity and if duration of exposure is long
enough, permanent impairment of vision or blindness will occur.
Skin:
Harmful by skin contact. This product will cause sensitisation by skin contact, which may lead to allergic contact
dermatitis. Will cause burns to the skin, with effects including; Redness, blistering, localised pain and severe rashes.
Inhaled:
May cause irritation to the nose, throat and respiratory system. However, this is only anticipated if the product is heated.
Chronic:
Prolonged or repeated skin contact will lead to necrosis (death) of the skin.
The following toxicological information is available for this product:
Oral LD50(rat): 2,500 mg/kg
Irritation:
Skin - Standard Draize Test:
Dermal LD50(rabbit): 5 mg/24H;
REACTION: Severe
Eye - Standard Draize Test:
Rabbit(Eyes): 20 mg/24 H;
REACTION: Severe
12. ECOLOGICAL INFORMATION
Ecotoxity:
Under current EU legislation this product is considered to be harmful to aquatic organisms and will cause adverse
effects in the aquatic environment.
Persistence / Degradability:
Not readily biodegradable. Will persist in the environment.
13. DISPOSAL CONSIDERATIONS
Refer to appropriate authority in your State. Dispose of material through a licensed waste contractor. Advise of
corrosive and combustible nature.
Material Safety Data Sheet
Page 5 of 6 Issue date: September 2004
M BOND AE-10
14. TRANSPORT INFORMATION
UN Number: 2259
Proper Shipping Name: TRIETHYLENE TETRAMINE
Dangerous Goods Class: 8
Packing Group: II
Hazchem Code: 2X
Label: Harmful (Xn), Corrosive (C)
Marine Transport:
UN Number: 2259
Proper Shipping Name: TRIETHYLENE TETRAMINE
Dangerous Goods Class: 8
Packing Group: II
Label: Harmful (Xn), Corrosive (C)
Air Transport:
UN Number: 2259
Proper Shipping Name: TRIETHYLENE TETRAMINE
Dangerous Goods Class: 8
Packing Group: II
Label: Harmful (Xn), Corrosive (C)
15. REGULATORY INFORMATION
Poison Schedule: S5 [Aust]
This product is a Scheduled (S5) Poison and must be stored, handled and used according to the appropriate regulations.
Inventory Status:
Australia (AICS) Y
United States (TSCA) Y
Canada (DSL) Y
Europe (EINECS/ELINCS) Y
Japan (MITI) Y
South Korea (KECL) Y
Y = all ingredients are on the inventory.
16. OTHER INFORMATION
Date of Preparation:
Issue date: September 3, 2004 Supercedes: January 8, 2004 and March 8, 2000
Reasons for Update:
nd
1. Alignment with the 2 Edition of National Code of Practice for the Preparation of Material Safety Data Sheets
[NOHSC:2001(2003)].
2. Changes and /or addition made to all sections.
Key Legend Information:
NOHSC - National Occupational Health & Safety Commission [Aust]
SUSDP - Standard for the Uniform Scheduling of Drugs and Poisons [Aust]
TWA - Time Weighted Average [Int]
STEL - Short Term Exposure Limit [Int]
AICS - Australian Inventory of Chemical Substances
EPA - Environmental Protection Agency [Int]
NIOSH - National Institute for Occupational Safety and Health [US]
AS/NZS 1715 - Selection, use and maintenance of respiratory protective devices. [Aust/NZ]
Material Safety Data Sheet
Page 6 of 6 Issue date: September 2004
M BOND AE-10
16. OTHER INFORMATION (Continued)
AS/NZS 1716 - Respiratory protective devices. [Aust/NZ]
(SAA/SNZ HB76:1997) - Dangerous Goods - Initial Emergency Response Guide [Aust/NZ]
AS 1940 - The Storage and Handling of Flammable and Combustible Liquids [Aust]
IATA - International Aviation Transport Authority [Int]
ICAO - International Civil Aviation Organization [Int]
IMO - International Maritime Organis ation. [Int]
IMDG - International Maritime Dangerous Goods [Int]
United Nations Recommendations for the Transport of Dangerous Goods and Globally Harmonized System for the
classification and labelling of Chemicals. [Int]
EU - European Union [Int]
[Aust/NZ] = Australian/New Zealand
[Int] = International
[US] = United States of America
Principal References:
Information supplied by manufacturer.
Disclaimer
To the best of our knowledge, the information provided above meets the requirements of European Union directives for
hazardous substances which have been tested as a whole. The data provided on this Material Safety Data Sheet is from
manufacturers of the original components. All animal test data has been obtained from the public domain, NO
ANIMAL TESTS have been conducted by Davidson Pty Ltd. Davidson Pty Ltd specifically disclaims any and all form
of liability and/or responsibility for the application of this product.
End of MSDS
|