MATERIAL SAFETY DATA SHEET
Page: 1
GENERIC MSDS FOR LAC AEROSO
12/20/2007
PRODUCT NAME: GENERIC MSDS FOR LAC AEROSO HMIS CODES: H F R P
FORMULA KEY: CUSTOM AEROSOL PR2 230I
================== SECTION I - MANUFACTURER IDENTIFICATION =================
MANUFACTURER'S NAME: Custom Aerosol Inc.
ADDRESS : 10010 Rearwin Dr
: McKinney, TX 75070
EMERGENCY PHONE : 1-972-346-2700 DATE PRINTED : 12/20/2007
INFORMATION PHONE : 1-972-346-2700 NAME OF PREPARER : Preston Staley
========== SECTION II - HAZARDOUS INGREDIENTS/SARA III INFORMATION =========
VAPOR PRESSURE WEIGHT
REPORTABLE COMPONENTS CAS NUMBER mm Hg @ TEMP PERCENT
-------------------------------------------------------------------------------------------------------------------------------
ACETONE 67-64-1 181.7 20 C 46.60
OSHA PEL: 750 PPM
ACGIH TLV: 500 PPM
ISOBUTANE 75-28-5 55 25 DEG C 11.20
OSHA PEL: 800 PPM
* XYLOL 1330-20-7 8 68 DEG F 10.70
OSHA PEL/TWA IS 100PPM
ACGIH TLV/TWA IS 100 PPM
ACGIH TLV/STEL IS 100 PPM
PROPANE 74-98-6 110 70 F 5.25
OSHA PEL: 1000 PPM
ACGIH TLV: 1000 PPM
1-METHOXY 2-PROPYL ACETATE 108-65-6 4.9 20 DEG C 1.85
ACGIH (THV) : NOT ESTABLISHED
OSHA PEL : NOT ESTABLISHED
EB ETHYLENE GLYCOL BUTYL ETHER 111-76-2 88 25 DEG C 1.55
OSHA PEL: 50 PPM
* ## ETHYL BENZENE 100-41-4 7.1 20 DEG C 1.45
OSHA PEL: 100 PPM
ACGIH TLV: 125 PPM
* METHYL ETHYL KETONE 78-93-3 83 75 F .85
OSHA PEL: 200 PPM
ACGIH TWA: 200 PPM
MINERAL SPIRITS 8052-41-3 5 100 F .85
OSHA PEL: 100 PPM
ACGIH TLV: 100 PPM
GLYCOL ETHER PM 107-98-2 88 25 DEG C .75
OSHA PEL: 50 PPM
* ETHYLENE GLYCOL N-BUTYL ETHER 111-76-2 .88 25 C .45
## BLACK 1333-86-4 3 68 F .20
BLACK PIGMENT IS A SOLID NOT A LIQUID.
OSHA PEL 3.5mg/m3
ACGIH TLV 3.5mg/m3
>>>>>>>>>>>>>>>>> AEROSOL CAN <<<<<<<<<<<<<<
This Aerosol Product should not be stored above 120掳 F. Do Not puncture. Keep from sparks and open flame. Containers may
explode when exposed to extreme heat. Do Not apply to hot surfaces.
=============== SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS ============
MATERIAL SAFETY DATA SHEET
Page: 2
GENERIC MSDS FOR LAC AEROSO
12/20/2007
BOILING RANGE: -43 F - 355 F WEIGHT PER GALLON: 6.4 lb/gl
VAPOR DENSITY: HEAVIER THAN AIR EVAPORATION RATE: SLOWER THAN ETHER
COATING V.O.C.: 4.046 lb/gl MATERIAL V.O.C.: 2.235 lb/gl
(WITHOUT EXEMPT SOLVENTS) (WITH EXEMPT SOLVENTS)
APPEARANCE AND ODOR:
Viscous liquid with an odor characteristic of the solvents listed in Section II.
================= SECTION IV - FIRE AND EXPLOSION HAZARD DATA ==============
FLASH POINT: -156 F METHOD USED:
FLAMMABLE LIMITS IN AIR BY VOLUME- LOWER: .8 UPPER: 13.1
EXTINGUISHING MEDIA:
Use National Fire Protection Association (NFPA) Class B extinguisher (CarbonDioxide, dry, chemical, or universal aqueous
film forming foam) designed to extinquish NFPA Flammable liquid fires.
SPECIAL FIREFIGHTING PROCEDURES:
Water spray may be ineffective. Water spray may be used to cool closed containers to prevent pressure build-up and
possible autoignition or explosion when exposed to extreme heat. If water is used, fog nozzles are preferrable. Fire-
fighters should wear self contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Keep container tightly closed. Isolate from heat, electrical equipment, sparks, and open flames. Closed containers may
explode when exposed to extreme heat. Do not apply on hot surfaces. Do not weld on or near container. Toxic gases may
form when product is contacted by flame or hot surfaces.
======================== SECTION V - REACTIVITY DATA =======================
STABILITY:
Stable at normal temperatures.
CONDITIONS TO AVOID:
Do not allow the can to exceed 120掳 F.
HAZARDOUS DECOMPOSITION OR BYPRODUCTS:
May produce hazardous decomposition products when heated. Welding, brazing, or flame-cutting on surfaces coated with
this product may produce fumes including: Carbon Monoxide or Carbon Dioxide.
HAZARDOUS POLYMERIZATION:
Not expected to occur.
==================== SECTION VI - HEALTH HAZARD DATA =======================
INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
Vapor and spray mist may be harmful if inhaled. Vapor irritates eyes, nose, and throat. Repeated exposure to high vapor
concentrations may cause irritation of the respiratory system and permanent brain and nervous system damage.
Intentional misuse by deliberately inhaling the contents can be harmful or fatal.
SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
Eye contact: causes eye irritation. May experience itching, burning sensation and visual disturbances.
SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
May cause moderate skin irritation. May be harmful if absorbed through the skin. Dryness, itching, cracking, burning,
redness, and swelling are conditions associated with excessive skin contact.
INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
Harmful or fatal if swallowed.
MATERIAL SAFETY DATA SHEET
Page: 3
GENERIC MSDS FOR LAC AEROSO
12/20/2007
HEALTH HAZARDS (ACUTE AND CHRONIC):
Avoid long term and repeated contact.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:
Not applicable.
EMERGENCY AND FIRST AID PROCEDURES:
INGESTION: If swallowed, do not induce vomiting. EYES: In case of eye contact, flush eyes immediately with plenty of
water for at least 15 minutes. SKIN: In case of skin contact, remove promptly by wiping, followed by waterless hand
cleaner and soap and water. INHALATION: If affected by inhalation of vapor or spray mist, remove to fresh air. Apply
artificial respiration and other supportive measures as required. Get medical attention.
=========== SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE ============
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Provide maximum ventilation. Only personnel equipped with proper respiratory and skin and eye protection should be
permitted in the area. Remove all sources of ignition. Take up spilled material with sawdust, vermiculite, or other
absorbent material and place into containers for disposal.
WASTE DISPOSAL METHOD:
Waste material must be disposed of in accordance with Federal, State, and Local environmental control regulations.
Empty containers should be recycled or disposed of through an approved Waste Management Facility.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING:
Do not store above 120 deg. F. Store large quantities in buildings designed and protected for storage of NFPA Flammable
liquids.
OTHER PRECAUTIONS:
If this material is part of a multiple component coating system, read the MSDS for the other component or components
before blending as the resulting mixture may have the hazards of all of its parts. Containers should be grounded when
pouring. Avoid free fall of liquids in excess of a few inchs. Containers of this material may be hazardous when
emptied since they retain residues. Do not cut, puncture, or weld on or near container.
===================== SECTION VIII - CONTROL MEASURES ======================
RESPIRATORY PROTECTION:
Overexposure to vapors may be prevented by ensuring ventilation controls, vapor exhaust or fresh air entry. If TLV of
any component is exceeded, use an appropriate NIOSH/MSHA approved respirator. Follow respirator manufacturers directions
for respirator use.
VENTILATION:
Provide sufficient mechanical and/or local exhaust ventilation to keep the concentration of ingredients listed in
Section II below the lowest exposure limits.
PROTECTIVE GLOVES:
Impermeable chemical handling gloves for skin protection.
EYE PROTECTION:
Use chemical safety glasses, goggles, and faceshields for eye protection.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT:
Use impermeable aprons and protective clothing whenever possible to prevent skin contact. The use of head caps whenever
possible is strongly recommended. Clean or discard contaminated clothing and shoes.
WORK/HYGIENIC PRACTICES:
Eye washes and safety showers in the workplace are recommended.
========================= SECTION IX - TRANSPORTATION INFORMATION ==========
MATERIAL SAFETY DATA SHEET
Page: 4
GENERIC MSDS FOR LAC AEROSO
12/20/2007
PROPER SHIPPING NAME HAZARD CLASS UN NUMBER PACKING GROUP
CONSUMER COMMODITY ORM-D DOES NOT APPLY DOES NOT APPLY
========================= SECTION X - DISCLAIMER ==========================
The information and recommendations contained herein are believed to be accurate at the time of preparation or obtained
from sources believed to be generally reliable. Fasse Paint Co. will not be held liable for claims relating to any
party's use of or reliance on information contained herein, regardless of whether it is claimed the information is
inaccurate.
|