Search    ENTER KEYWORD
MSDS Material Safety Data Sheet
CAS

1332-09-8
14808-60-7

File Name: davidson_com_au---gc-5-pumice.asp
                       Material Safety Data Sheet
Page 1 of 5 Issue date: February 2005

GC-5 PUMICE POWDER
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Davidson Measurement Pty. Ltd
ACN: 005 031 961 ABN: 29 005 031 961
Phone: 03 9580 4366
Fax: 03 9580 6499
Email: info@davidson.com.au
Web: www.davidson.com.au
Address: 1-3 Lakewood Boulevard,
Braeside, Victoria, 3195.
Product Name: GC-5 PUMICE POWDER
Manufacturer's Product Code: MGM051D

Use: Produces a dull, matte finish. Recommended for minimal removal of surface material.

2. HAZARDS IDENTIFICATION
NOT CLASSIFIED AS HAZARDOUS ACCORDING TO EU CRITERIA

Hazard Category: None allocated

Hazard Classification: NON-HAZARDOUS SUBSTANCE, NON-DANGEROUS GOOD

RISK PHRASES
None allocated

SAFETY PHRASES
S22 Do not breathe dust.

Road Transport
UN Number: None allocated
Proper Shipping Name: NONE ALLOCATED
Dangerous Goods Class: None allocated
Packing Group: None allocated
Label: None allocated

Poison Schedule: None allocated [Aust].

3. COMPOSITION / INFORMATION ON INGREDIENTS
SUBSTANCE NAME Proportion CAS Number
PUMICE STONE > 99 % 1332-09-8
CRYSTALLINE SILICA < 0.1 % 14808-60-7

This product may contain low levels of crystalline silica, however, there is no evidence to indicate that the trace
amounts of crystalline silica present in this product will cause any carcinogenic effect.
All ingredients not hazardous according to EU Criteria.

4. FIRST AID MEASURES
Swallowed:
If swallowed, DO NOT induce vomiting. If conscious, give 1 to 2 glasses of water to drink. If irritation persists
transport to hospital or doctor.

Eye:
If dust enters the eyes, flush with plenty of water for at least 15 minutes, ensuring eye lids are held open. If irritation
persists, immediately transport to hospital or doctor.
Material Safety Data Sheet
Page 2 of 5 Issue date: February 2005

GC-5 PUMICE POWDER
4. FIRST AID MEASURES (Continued)
Skin:
If dust is falls onto the skin, remove any contaminated clothing and wash skin thoroughly with soap and water. If
irritation persists transport to hospital or doctor.
Inhaled:
Move victim to fresh air. Apply resuscitation if victim is not breathing - If trained personnel available administer
oxygen if breathing is difficult.

First Aid Facilities:
Eye wash fountain, safety shower and normal wash room facilities.

Advice to Doctor:
Treat symptomatically.
In case of poisoning, contact Poisons Information Centre
In Australia call Tel: 131126
In New Zealand Tel: 034747000

5. FIRE-FIGHTING MEASURES
Fire/Explosion Hazard
If safe to do so, move undamaged containers from fire area.
Suitable Extinguishing Media: Use extinguishing media suitable for surrounding fire situation.
Hazards From Combustion Products: Primary decomposition products include oxides of silicon, and small quantities
of noxious smoke.
Precautions for Fire Fighters and Special Protective Equipment: Fire fighters to wear Self-contained breathing
apparatus (SCBA) in confined spaces, in oxygen deficient atmospheres or if exposed to products of decomposition. Full
protective clothing is also recommended.

HAZCHEM CODE: None allocated [Aust]

FLAMMABILITY
This material is not a combustible or flammable solid.

6. ACCIDENTAL RELEASE MEASURES
Emergency Procedures:
Avoid generating dusts. Low hazard product, use common sense in handling situation.

Methods and Materials for Containment and Clean Up Procedures:
This product is a heavy powder. If safe to do so, wet area to prevent high dust levels. Wear suitable protective
equipment. Shovel up any spill or if available, use dustless methods, such as a HEPA vacuum and filter. Place waste
into suitably labelled container for disposal.

7. HANDLING AND STORAGE
Precautions for Safe Handling:
Avoid generating and inhaling dusts. Provide adequate ventilation. Low hazard product. For further information please
refer to the Engineering Controls of this MSDS.

Conditions for Safe Storage:
Store in original packages as approved by manufacturer.
Material Safety Data Sheet
Page 3 of 5 Issue date: February 2005

GC-5 PUMICE POWDER
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Exposure Standards

No exposure standards are available for this product, however, the following exposure standards have been assigned by
[NOHSC] to the following components of the product:

PUMICE POWDER
[NOHSC]
[TWA] 10 mg/m3
Present as Nuisance dust not otherwise specified

CRYSTALLINE SILICA
[NOHSC]
3
[TWA] 0.2 mg/m

Engineering Controls
Maintain adequate ventilation at all times. In most circumstances natural ventilation systems are adequate

Personal Protection Equipment
GLOVES: Neoprene rubber.
EYES: Spectacles to protect eyes.
RESPIRATORY PROTECTION: Avoid breathing of dusts. The use of a respirator is not normally required,
however, if high dust levels are present, then the use of a suitable dust mask is recommended. All respirators must
comply with AS/NZS 1715 and AS/NZS 1716.

9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Gray powder or fine granules.
Boiling Point Melting Point: Not available.
Melting Point: Not available.
Vapour Pressure: Not available.
Specific Gravity: Not available.
Flash Point: Not applicable.
Flammability Limits: Not applicable.
Solubility in Water: Insoluble.

Other Properties
Vapor Density (Air = 1): Not available.

10. STABILITY AND REACTIVITY
CHEMICAL STABILITY:
Stable under normal conditions of use.

CONDITIONS TO AVOID:
Low hazard product.

INCOMPATIBLE MATERIALS:
Strong mineral acids (sulfuric, nitric and hydrochloric), and energetic oxidizing agents.

HAZARDOUS DECOMPOSITION PRODUCTS:
Primary decomposition products include oxides of silicon, and small quantities of noxious smoke.

HAZARDOUS REACTIONS:
Will not occur.
Material Safety Data Sheet
Page 4 of 5 Issue date: February 2005

GC-5 PUMICE POWDER
11. TOXICOLOGICAL INFORMATION
ACUTE HEALTH EFFECTS:
Swallowed:
Very low hazard, difficulty in swallowing pumice would prevent injury.

Eye:
May cause mechanical irritation to the eyes, with effects including: tearing, pain, stinging and blurred vision.

Skin:
May cause mechanical irritation to the skin, with effects including; Redness and itchiness.

Inhaled:
Dust from the product may cause irritation to the respiratory system.

Chronic:
This product may contain low levels of crystalline silica, however, there is no evidence to indicate that the trace
amounts of crystalline silica present in this product will have a carcinogenic effect.

12. ECOLOGICAL INFORMATION
There is no ecological information available for this product, it is not considered an environmental hazard to the
environment.

13. DISPOSAL CONSIDERATIONS
Refer to appropriate authority in your State. Dispose of material through a licensed waste contractor or at an approved
landfill site.

14. TRANSPORT INFORMATION
Road Transport
UN Number: None allocated
Proper Shipping Name: NONE ALLOCATED
Dangerous Goods Class: None allocated
Packing Group: None allocated
Label: None allocated

Air Transport
UN Number: None allocated
Proper Shipping Name: NONE ALLOCATED
Dangerous Goods Class: None allocated
Packing Group: None allocated
Label: None allocated

Sea Transport
UN Number: None allocated
Proper Shipping Name: NONE ALLOCATED
Dangerous Goods Class: None allocated
Packing Group: None allocated
Label: None allocated
Material Safety Data Sheet
Page 5 of 5 Issue date: February 2005

GC-5 PUMICE POWDER
15. REGULATORY INFORMATION
Poison Schedule: None allocated [Aust]

Inventory Status:
Australia (AICS) Y
United States (TSCA) Y
Europe (EINECS/ELINCS) Y

Y = all ingredients are on the inventory.

16. OTHER INFORMATION
Date of Preparation:

Issue date: February 7, 2004 Supercedes: March 23, 2000

Reasons for Update:
nd
1. Alignment with the 2 Edition of National Code of Practice for the Preparation of Material Safety Data Sheets
[NOHSC:2001(2003)].
2. Changes and /or addition made to all sections.

Key Legend Information:
NOHSC - National Occupational Health & Safety Commission [Aust]
SUSDP - Standard for the Uniform Scheduling of Drugs and Poisons [Aust]
TWA - Time Weighted Average [Int]
STEL - Short Term Exposure Limit [Int]
AICS - Australian Inventory of Chemical Substances
EPA - Environmental Protection Agency [Int]
NIOSH - National Institute for Occupational Safety and Health [US]
AS/NZS 1715 - Selection, use and maintenance of respiratory protective devices. [Aust/NZ]
AS/NZS 1716 - Respiratory protective devices. [Aust/NZ]
(SAA/SNZ HB76:1997) - Dangerous Goods - Initial Emergency Response Guide [Aust/NZ]
IATA - International Aviation Transport Authority [Int]
ICAO - International Civil Aviation Organization [Int]
IMO - International Maritime Organisation. [Int]
IMDG - International Maritime Dangerous Goods [Int]
United Nations Recommendations for the Transport of Dangerous Goods and Globally Harmonized System for the
classification and labelling of Chemicals. [Int]
EU - European Union [Int]

[Aust/NZ] = Australian/New Zealand
[Int] = International
[US] = United States of America

Principal References:
Information supplied by manufacturer.

Disclaimer
To the best of our knowledge, the information provided above meets the requirements of European Union directives for
hazardous substances which have been tested as a whole. The data provided on this Material Safety Data Sheet is from
manufacturers of the original components. All animal test data has been obtained from the public domain, NO
ANIMAL TESTS have been conducted by Davidson Pty Ltd. Davidson Pty Ltd specifically disclaims any and all form
of liability and/or responsibility for the application of this product.

END of MSDS

Search    ENTER KEYWORD
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP
NAMECAS
cps_screen_wash_t.asp 2004-01-1 34590-94-8 112-34-5 64742-47-8
crowmktg_com---cd-catalog-2007.asp N/A
custom-aerosol_com---generic-msds-acrylic-lacquer-aerosol.asp 67-64-1 1330-20-7 75-28-5 74-98-6 100-41-4 108-65-6 111-76-2 8052-41-3 107-98-2
custom-aerosol_com---msds-alv-aerosol-with-propellant.asp N/A
custom-aerosol_com---msds-custom-aerosol-aerosol-lacquer_12-2007.asp 67-64-1 75-28-5 1330-20-7 74-98-6 108-65-6 111-76-2 100-41-4 78-93-3 8052-41-3 107-98-2 1333-86-4
custom-aerosol_com---msds-custom-aerosol-lacquer-bulk_12-2007.asp 67-64-1 1330-20-7 108-65-6 100-41-4 78-93-3 8052-41-3 111-76-2 1333-86-4 107-98-2 108-88-3
custom-aerosol_com---msds-duranar-ads.asp 800-00-2
custom-aerosol_com---msds-ppg-acrylic-flourocarbon.asp N/A
custom-aerosol_com---msds-ppg-dp401lf.asp 800-00-2 111-76-2 1330-20-7 64742-95-6 67-63-0 68410-23-1 71-23-8 95-63-6
custom-aerosol_com---msds-ppg-dp40lf.asp 800-00-2 100-41-4 108-10-1 108-88-3 110-43-0 111-76-2 112926-00-8 1317-65-3 1330-20-7 1333-86-4 13463-67-7 14807-96-6 14808-60-7 25068-38-6 25086-48-0 64742-95-6 7727-43-7 95-63-6
custom-aerosol_com---msds-ppg-uc51760.asp 800-00-2 108-65-6 108-88-3 1332-58-7 13463-67-7 70657-70-4 7789-06-2 78-93-3
custom-aerosol_com---msds-unfilled-omni-fill.asp N/A
custom-aerosol_com---ppg-dp40-msds_6-29-2007.asp 78-93-3 25068-38-6 7727-43-7 110-19-0 123-86-4 800-00-2 7789-06-2 13463-67-7 14807-96-6 67-63-0 25086-48-0 107-98-2 108-88-3 763-69-9 1330-20-7 1333-86-4 100-41-4 14808-60-7 11103-86-9
custom-aerosol_com---ppg-dp401-msds_5-26-2006.asp 800-00-2
custom-aerosol_com---ppg-uc51760-msds_1-25-2007.asp 108-88-3 1332-58-7 108-65-6 13463-67-7 800-00-2 78-93-3 7789-06-2 85-68-7 70657-70-4
custom-aerosol_com---ppg-uc60400-msds_3-29-2007.asp 800-00-2
davidson_com_au---barrier_e.asp 14807-96-6 1333-86-4 1344-40-1 8052-42-4 1309-64-4
davidson_com_au---csm1a-degreaser.asp 1717-00-6 67-56-1 124-38-9
davidson_com_au---epoxylite_813_part_a.asp 14808-60-7 14807-96-6 25068-38-6 28064-14-4
davidson_com_au---epoxylite_813_part_b.asp 14808-60-7 14807-96-6 89-32-7
davidson_com_au---epoxy_br_22_part_a.asp 97-99-4 14808-60-7 14807-96-6 25068-38-6
davidson_com_au---epoxy_br_22_part_b.asp 14808-60-7 14807-96-6 89-32-7
davidson_com_au---gagekote_1.asp 108-88-3 1330-20-7
davidson_com_au---gagekote_11.asp 108-88-3
davidson_com_au---gagekote_5_part_b.asp 25068-38-6 97-99-4
davidson_com_au---gagekote_7_part_a.asp 25085-99-8 108-46-3
davidson_com_au---gagekote_7_part_b.asp 4246-51-9 111-40-0 90-72-2
davidson_com_au---gc-5-pumice.asp 1332-09-8 14808-60-7
davidson_com_au---gc_adhesive.asp 409-21-2 7732-18-5 1344-28-1 7664-38-2 7631-86-9 10043-35-3 64-17-5
davidson_com_au---h-cement.asp 14808-60-7 7664-38-2 1344-28-1 1308-38-9 1333-82-0
davidson_com_au---m-bond-200-adhesive.asp 7085-85-0 9011-14-7
davidson_com_au---m-bond-200-catalyst-c.asp 67-63-0 120-07-0
davidson_com_au---m-bond-300-catalyst.asp 131-11-3 1338-23-4 25265-71-8 7722-84-1
davidson_com_au---m-bond-300-resin.asp 100-42-5 96-09-3
davidson_com_au---m-bond-43-b.asp 78-93-3 1330-20-7 25068-38-6 123-42-2
davidson_com_au---m-bond-600-adhesive.asp 109-99-9 28064-14-4 78-93-3
davidson_com_au---m-bond-ae-10.asp 112-24-3
davidson_com_au---m-bond-curing-agent-10.asp 112-24-3
davidson_com_au---m-bond-ga-100-cement.asp 7631-86-9 14808-60-7 7732-18-5 13530-50-2 9000-65-1 1333-82-0 7664-38-2
davidson_com_au---m-coat-a.asp 1330-20-7 100-41-4
davidson_com_au---m-coat-c.asp 67-56-1 1185-55-3 8032-32-4 1330-20-7
davidson_com_au---m-line_450-20r.asp 7440-31-5 7440-36-0 8050-09-7
davidson_com_au---m-line_450-20s_solder.asp 7440-31-5 7440-36-0
davidson_com_au---m-line_570-25r.asp 7439-92-1 7440-31-5 8050-09-7 7440-22-4
davidson_com_au---m-line_rosin_solvent.asp 67-63-0 108-88-3
davidson_com_au---mbond-450-partb.asp N/A
davidson_com_au---mbond-610-adhesive.asp 109-99-9 28064-14-4 78-93-3
davidson_com_au---mbond-a-12part-b.asp 1344-28-1 112-24-3 13463-67-7
davidson_com_au---mbond-a-12_-part_a.asp 25068-38-6 14808-60-7 1344-28-1 1309-37-1
davidson_com_au---mbond-curing-agent-15.asp 104-78-9

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com | Ads link:HBCCHEM.INC