MATERIAL SAFETY DATA SHEET
Material/ Percent Hazardous
SECTION 1 - PRODUCT AND COMPANY INFORMATION
CAS Number
METHYL ETHYL KETONE 10 - 30 X
78-93-3
Refinish Products
EPOXY RESIN 7 - 13 X
19699 Progress Drive
25068-38-6
Strongsville, OH 44149
BARIUM SULFATE 7 - 13 X
7727-43-7
EMERGENCY PHONE NUMBERS (412) 434-4515 (U.S.) ISOBUTYL ACETATE 5 - 10 X
(24 hours/day): 110-19-0
N-BUTYL ACETATE 5 - 10 X
(514) 645-1320 (Canada)
123-86-4
01-800-00-21-400 (Mexico)
STRONTIUM CHROMATE 3-7 X
0532-83889090 (China) 7789-06-2
TECHNICAL (740) 363-9610 (DELAWARE, OH) 8:00 a.m. - TITANIUM DIOXIDE 3-7 X
INFORMATION: 5:00 p.m. EST 13463-67-7
TALC 3-7 X
PRODUCT SAFETY/MSDS INFORMATION: (412) 492-5555 7:00 a.m.
14807-96-6
- 4:30 p.m. EST
ISOPROPYL ALCOHOL 3-7 X
Product ID: DP40 (0808)
67-63-0
PRODUCT NAME: NON SANDING EPOXY PRIMER VINYL RESIN 1-5 X
SYNONYMS: None 25086-48-0
ISSUE DATE: 06/29/2007 PROPYLENE GLYCOL 1-5 X
EDITION NO.: 9 MONOMETHYL ETHER
107-98-2
CHEMICAL Epoxy Vinyl
TOLUENE 1-5 X
FAMILY:
108-88-3
EMERGENCY OVERVIEW: ETHYL 3- 1-5 X
Flammable. Keep away from heat, sparks, flames, and other sources of ETHOXYPROPANOATE
ignition. Do not smoke. Extinguish all flames and pilot lights. Turn off 763-69-9
stoves, heaters, electrical motors, and other sources of ignition during XYLENES 0.5-1.5 X
1330-20-7
use and until all vapors/odors are gone.CAUSES SEVERE EYE
CARBON BLACK 0.1-1.0 X
IRRITATION. CAUSES PRIMARY SKIN IRRITATION. MAY BE
1333-86-4
ABSORBED THROUGH THE SKIN. PROLONGED OR REPEATED
ETHYL BENZENE 0.1-1.0 X
CONTACT MAY CAUSE AN ALLERGIC SKIN REACTION.VAPOR 100-41-4
AND/OR SPRAY MIST MAY BE HARMFUL IF INHALED. SANDING QUARTZ 0.1-1.0 X
AND GRINDING DUSTS MAY BE HARMFUL IF INHALED. VAPOR 14808-60-7
IRRITATES EYES, NOSE, AND THROAT. VAPOR GENERATED AT ZINC POTASSIUM CHROMATE 0.1-1.0 X
11103-86-9
ELEVATED TEMPERATURES IRRITATES EYES, NOSE AND
(As Chromium (VI) Cmpnds) * X See Sections 8
THROAT. MAY CAUSE IRRITATION AND/OR ALLERGIC
11103-86-9 and 15 for
RESPIRATORY REACTION IN LUNGS.HARMFUL IF SWALLOWED.
information.
DRIED FILM OF THIS PRODUCT MAY BE HARMFUL IF CHEWED OR (As Zinc Cmpnds) * X See Sections 8
SWALLOWED. 11103-86-9 and 15 for
information.
(As Chromium Cmpnds) * X See Sections 8
11103-86-9 and 15 for
SECTION 2 - COMPOSITION INFORMATION information.
The following ingredient(s) marked with an "x" are considered (As Chromates) * X See Sections 8
hazardous under applicable U.S. OSHA and/or Canadian WHMIS 11103-86-9 and 15 for
regulations. If no ingredients are listed, then there are no U.S. OSHA information.
(As inorganic Chromium cmpnds) * X See Sections 8
and/or Canadian WHMIS hazardous ingredients in this product.
11103-86-9 and 15 for
information.
(As Silica, crystalline and Quartz) * X See Sections 8
14808-60-7 and 15 for
information.
(As Chromium (VI) Cmpnds) * X See Sections 8
7789-06-2 and 15 for
information.
(As Chromium Cmpnds) * X See Sections 8
7789-06-2 and 15 for
information.
(As Chromates) * X See Sections 8
7789-06-2 and 15 for
information.
(As inorganic Chromium cmpnds) * X See Sections 8
7789-06-2 and 15 for
information.
SECTION 3 - HAZARDS IDENTIFICATION
ACUTE OVEREXPOSURE EFFECTS
EYE CONTACT:
Causes severe eye irritation. Redness, itching, burning sensation and
visual disturbances may indicate excessive eye contact.
__________________________________________________________________
Page 1 of 7
_______________________________________________________________________________________________________________
Refinish Products
19699 Progress Drive
Strongsville, OH 44149
Product ID: DP40 (0808)
PRODUCT NAME: NON SANDING EPOXY PRIMER
SKIN CONTACT: SECTION 4 - FIRST AID MEASURES
Causes primary skin irritation. Dryness, itching, cracking, burning, If ingestion, irritation, any type of overexposure or symptoms of
redness, and swelling are conditions associated with excessive skin overexposure occur during or persists after use of this product, contact a
contact. POISON CONTROL CENTER, EMERGENCY ROOM OR PHYSICIAN
SKIN ABSORPTION: immediately; have Material Safety Data Sheet information available.
May be absorbed through the skin. Prolonged or repeated contact may EYE CONTACT:
cause an allergic skin reaction. Remove contact lens and pour a gentle stream of warm water through the
INHALATION: affected eye for at least 15 minutes. If irritation persists, contact a poison
Vapor and/or spray mist may be harmful if inhaled. Sanding and grinding control center, emergency room, or physician as further treatment may be
dusts may be harmful if inhaled. Vapor irritates eyes, nose, and throat. necessary.
Vapor generated at elevated temperatures irritates eyes, nose and throat. SKIN CONTACT:
May cause irritation and/or allergic respiratory reaction in lungs. Run a gentle stream of water over the affected area for 15 minutes. A
INGESTION: mild soap may be used if available. If any symptoms persist, contact a
Harmful if swallowed. Dried film of this product may be harmful if chewed poison control center, emergency room, or physician as further treatment
or swallowed. may be necessary.
SIGNS & SYMPTOMS OF OVEREXPOSURE: INHALATION:
Repeated exposure to high vapor concentrations may cause irritation of Remove from area to fresh air. If symptomatic, contact a poison control
the respiratory system and permanent brain and nervous system center, emergency room or physician for treatment information.
damage. Eye watering, headaches, nausea, dizziness and loss of INGESTION:
coordination are indications that solvent levels are too high. Intentional Gently wipe or rinse the inside of the mouth with water. Sips of water
misuse by deliberately concentrating and inhaling the contents can be may be given if person is fully conscious. Never give anything by mouth
harmful or fatal. Dryness, itching, cracking, burning, redness, and to an unconscious or convulsing person. Do Not induce vomiting.
swelling are conditions associated with excessive skin contact. Contact a poison control center, emergency room or physician right away
as further treatment will be necessary.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Not
applicable. SECTION 5 - FIRE FIGHTING MEASURES
CHRONIC OVEREXPOSURE EFFECTS
FLAMMABLE PROPERTIES
Avoid long-term and repeated contact.
FLASHPOINT: 30 Degrees F ( -1 Degrees C)
Repeated exposure to vapors above recommended exposure limits (see
FLASHPOINT TEST METHOD:
Section 8) may cause irritation of the respiratory system and permanent
Pensky-Martens Closed Cup
brain and nervous system damage. Intentional misuse by deliberately
UEL: Not Available.
concentrating and inhaling the contents can be harmful or fatal.
LEL: 1.7
Prolonged exposure to an ingredient(s) in this product may cause kidney
AUTOIGNITION TEMPERATURE:
and/or liver damage. This product contains crystalline silica which has
Not Available.
been classified as a human carcinogen by IARC. Long-term exposures
EXTINGUISHING MEDIA:
may also lead to a disabling lung condition known as silicosis. The risk
Use National Fire Protection Association (NFPA) Class B extinguishers
depends on the duration and level of exposure to dust from sanding
(carbon dioxide, dry chemical, or universal aqueous film forming foam)
surfaces or mist from spray applications. Use of appropriate personal
designed to extinguish NFPA Class IB flammable liquid fires. Water spray
protective equipment and/or engineering controls should be employed
may be ineffective. Water spray may be used to cool closed containers
whenever these types of operations are being performed. NTP, IARC,
to prevent pressure build-up and possible autoignition or explosion when
and OSHA have classified chromium (+6) compounds as carcinogenic.
exposed to extreme heat.
OSHA considers all Cr+6 compounds as potential occupational
PROTECTION OF FIREFIGHTERS:
carcinogens capable of causing lung cancer above the recommended
Fire-fighters should wear self-contained breathing apparatus and full
exposure limits. This product contains toluene. Toluene inhalation in
protective clothing.
animals (greater than 1500 ppm) and intentional inhalation of toluene-
UNUSUAL FIRE AND EXPLOSION HAZARDS:
containing products by humans (e.g. glue) has caused adverse fetal
Keep this product away from heat, sparks, flame, and other sources of
development effects. This product contains talc. In a lifetime inhalation
ignition (i.e., pilot lights, electric motors, static electricity). Invisible vapors
study female rats exposed to an elevated respirable concentration (9
can travel to a source of ignition and flash back. Do not smoke while
times the Permissible Exposure Limit) of cosmetic grade talc developed
using this product. Keep containers tightly closed when not in use. Closed
lung cancer. High exposures to xylenes in some animal studies have
containers may explode when overheated. Do not apply to hot surfaces.
been reported to cause health effects on the developing embryo and
Toxic gases may form when this product comes in contact with extreme
fetus. These effects were often at levels toxic to the mother. There is
heat. This product contains an ingredient which may form explosive
some evidence that repeated exposure to organic solvent vapors in
peroxides during evaporation and may become heat and impact
combination with constant loud noise can cause greater hearing loss than
sensitive. May produce hazardous decomposition products when
expected from exposure to noise alone. An ingredient in this product has
exposed to extreme heat. Extreme heat includes, but is not limited to,
caused fetal toxicity in experimental animals. The significance of these
flame cutting, brazing, and welding.
findings for humans is unknown.
The effects of long-term, low level exposures to this product have not
SECTION 6 - ACCIDENTAL RELEASE MEASURE
been determined. Safe handling of this material on a long-term basis
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED:
should emphasize the prevention of all contact with this material to avoid
Provide maximum ventilation. Only personnel equipped with proper
any effects from repetitive acute exposures. See Section 11, of this
respiratory, skin, and eye protection should be permitted in the area.
MSDS for a detailed list of chronic health effects information available on
Remove all sources of ignition. Take up spilled material with sand,
individual ingredients in this product.
vermiculite, or other noncombustible absorbent material and place in
clean, empty containers for disposal. Only the spilled material and the
absorbant should be placed in this container.
__________________________________________________________________
Page 2 of 7
_______________________________________________________________________________________________________________
Refinish Products
19699 Progress Drive
Strongsville, OH 44149
Product ID: DP40 (0808)
PRODUCT NAME: NON SANDING EPOXY PRIMER
Material/ Percent ACGIH TLV ACGIH OSHA PEL OSHA
SECTION 7 - HANDLING AND STORAGE
CAS Number STEL STEL
PRECAUTIONS TO BE TAKEN DURING HANDLING AND STORAGE:
METHYL ETHYL 10 - 30 200 ppm 300 ppm 200 ppm 300 ppm
Vapors may collect in low areas. If this material is part of a multiple
KETONE
component system, read the Material Safety Data Sheet(s) for the other 78-93-3
component or components before blending as the resulting mixture may 10 MG/m3 R- 5 mg/m3
BARIUM SULFATE 7 - 13 Not Not
have the hazards of all of its parts. Containers should be grounded when 7727-43-7 established established
pouring. Avoid free fall of liquids in excess of a few inches. ISOBUTYL 5 - 10 150 ppm Not 150 ppm Not
STORAGE: ACETATE established established
110-19-0
Do not store above 120 degrees F.(48 degrees C.). Store large quantities
N-BUTYL ACETATE 5 - 10 150 PPM 200 ppm 150 ppm 200 ppm
in buildings designed and protected for storage of NFPA Class IB
123-86-4
flammable liquids.
STRONTIUM 3-7 0.0005 Not Not Not
MG/m3
CHROMATE established established established
SECTION 8 - EXPOSURE CONTROLS & PERSONAL PROTECTION 7789-06-2
10 mg/m3 10 mg/m3
TITANIUM DIOXIDE 3-7 Not Not
ENGINEERING CONTROLS:
13463-67-7 established established
Provide general dilution or local exhaust ventilation in volume and pattern
R- 2 mg/m3
TALC 3-7 R- 2 Not Not
to keep the concentration of ingredients listed in Section 8 below the
MG/m3
14807-96-6 established established
lowest suggested exposure limits, the LEL below the stated limit, and to
ISOPROPYL 3-7 200 PPM 400 PPM 400 ppm 500 ppm
remove decomposition products during welding or flame cutting. ALCOHOL
67-63-0
PROPYLENE 1-5 100 PPM 150 PPM 100 ppm 150 ppm
PERSONAL PROTECTIVE EQUIPMENT
GLYCOL
EYES: MONOMETHYL
Wear chemical-type splash goggles and full face shield when possibility ETHER
exists for eye contact due to splashing or spraying liquid, airborne 107-98-2
particles, or vapors. TOLUENE 1-5 S- 50 ppm Not 100 ppm 150 ppm
SKIN/GLOVES: 108-88-3 established
XYLENES 0.5-1.5 100 ppm 150 PPM 100 ppm 150 ppm
Wear protective clothing to prevent skin contact. Apron and gloves
1330-20-7
should be constructed of: neoprene rubber. No specific 3 3
CARBON BLACK 0.1-1.0 3.5 mg/m Not 3.5 mg/m Not
permeation/degradation testing have been done on protective clothing for
1333-86-4 established established
this product. Recommendations for skin protection are based on
ETHYL BENZENE 0.1-1.0 100 ppm 125 ppm 100 ppm 125 ppm
infrequent contact with this product. For frequent contact or total 100-41-4
immersion, contact a manufacturer of protective clothing for appropriate QUARTZ 0.1-1.0 R- 0.025 Not R- 0.1 Not
chemical impervious equipment. Clean contaminated clothing and shoes. MG/m3 mg/m3
14808-60-7 established established
RESPIRATOR: 0.01 MG/m3
ZINC POTASSIUM 0.1-1.0 Not Not Not
Overexposure to vapors may be prevented by ensuring proper ventilation CHROMATE established established established
11103-86-9
controls, vapor exhaust or fresh air entry. A NIOSH- approved air
0.05 mg/m3 5[MU]G/m3
(As Chromium (VI) * Not Not
purifying respirator with the appropriate chemical cartridges or a positive-
Cmpnds) established established
pressure, air-supplied respirator may also reduce exposure. Read the
11103-86-9
respirator manufacturer's instructions and literature carefully to determine
(As Chromates) * Not Not C- 0.1 Not
the type of airborne contaminants against which the respirator is effective, mg/m3
11103-86-9 established established established
its limitations, and how it is to be properly fitted and used. Provide general 3 3
(As Chromium (VI) * 0.05 mg/m Not 5[MU]G/m Not
dilution or local exhaust ventilation in volume and pattern to keep the Cmpnds) established established
concentration of ingredients listed in Section 2 below the lowest 7789-06-2
suggested exposure limits, the LEL below the stated limit, and to remove (As Chromates) * Not Not C- 0.1 Not
mg/m3
7789-06-2 established established established
decomposition products during welding or flame cutting.
GENERAL HYGIENE - ESTABLISHED EXPOSURE LIMITS
If Threshold Limit Values (TLVs) have been established by ACGIH,
OSHA, Ontario or PPG, they will be listed below. These limits are
intended for use in the practice of industrial hygiene as guidelines or
recommendations in the control of potential workplace health hazards.
These limits are not a relative index of toxicity and should not be used by
anyone without industrial hygiene training.
__________________________________________________________________
Page 3 of 7
_______________________________________________________________________________________________________________
Refinish Products
19699 Progress Drive
Strongsville, OH 44149
Product ID: DP40 (0808)
PRODUCT NAME: NON SANDING EPOXY PRIMER
Vapour Pressure: 36.9 mmHg
Material/ Percent Ontario Ontario PPG IPEL PPG STEL
CAS Number TWA STEL ODOR/APPEARANCE: Viscous liquid with an odor
METHYL ETHYL 10 - 30 200 ppm 300 ppm Not Not characteristic of the solvents listed in
KETONE established established Section 2.
78-93-3
VAPOR DENSITY: HEAVIER THAN AIR
10 MG/m3
BARIUM SULFATE 7 - 13 Not Not Not
Evaporation Rate: 337
7727-43-7 established established established
BOILING POINT OR RANGE: 172 - 338Degrees F
ISOBUTYL 5 - 10 150 ppm 187 ppm Not Not
Freezing Point or Range: Not Applicable.
ACETATE established established
Melting Point or Range(掳C): Not Applicable.
110-19-0
Partition coefficient (n- Not Applicable.
N-BUTYL ACETATE 5 - 10 150 ppm 200 ppm Not Not
123-86-4 established established octanol/water):
STRONTIUM 3-7 0.0005 Not Not Not WEIGHT PER GALLON: 10.25 (U.S.) / 12.3 (IMPERIAL)
MG/m3
CHROMATE established established established
7789-06-2
10 MG/m3
TITANIUM DIOXIDE 3-7 Not Not Not
SECTION 10 - STABILITY AND REACTIVITY
13463-67-7 established established established
TALC 3-7 R- 2 Not Not Not STABILITY:
MG/m3
14807-96-6 established established established This product is normally stable and will not undergo hazardous reactions.
ISOPROPYL 3-7 200 PPM 400 PPM Not Not CONDITIONS TO AVOID:
ALCOHOL established established
None Known.
67-63-0
INCOMPATIBLE MATERIALS:
PROPYLENE 1-5 100 ppm 150 ppm Not Not
Avoid contact with strong alkalies, strong mineral acids, or strong
GLYCOL established established
oxidizing agents.
MONOMETHYL
HAZARDOUS POLYMERIZATION:
ETHER
107-98-2 None Known.
TOLUENE 1-5 50 PPM Not Not Not HAZARDOUS DECOMPOSITION PRODUCTS:
108-88-3 established established established - Carbon monoxide - Carbon dioxide - Oxides of chromium - Oxides of
ETHYL 3- 1-5 50 PPM Not 50 PPM 100 PPM
sulfur - Oxides of barium - Lower molecular weight polymer fractions
ETHOXYPROPANO established
ATE
763-69-9
XYLENES 0.5-1.5 100 ppm 150 ppm Not Not
SECTION 11 - TOXICOLOGICAL INFORMATION
1330-20-7 established established
3.5 mg/m3
CARBON BLACK 0.1-1.0 Not Not Not ACUTE TOXICITY
1333-86-4 established established established
ETHYL BENZENE 0.1-1.0 100 PPM 125 PPM Not Not Material/ Percent ORAL DERMAL INHALATION
100-41-4 established established CAS Number LD50 (g/kg) LD50 (g/kg) LC50 (mg/l)
3
QUARTZ 0.1-1.0 0.10 MG/m Not Not Not METHYL ETHYL 10 - 30 2.74 g/kg 13.00 g/kg Not Available
14808-60-7 established established established KETONE
3
ZINC POTASSIUM 0.1-1.0 0.01 MG/m Not Not Not 78-93-3
CHROMATE established established established EPOXY RESIN 7 - 13 2.00 g/kg 2.00 g/kg Not Available
11103-86-9 25068-38-6
3
(As Chromium (VI) * 0.05 mg/m Not Not Not ISOBUTYL 5 - 10 13.40 g/kg Not Available Not Available
Cmpnds) established established established ACETATE
11103-86-9 110-19-0
0.05 mg/m3
(As Chromates) * Not Not Not N-BUTYL ACETATE 5 - 10 10.77 g/kg 17.60 g/kg Not Available
11103-86-9 established established established 123-86-4
3
(As Chromium (VI) * 0.05 mg/m Not Not Not STRONTIUM 3-7 3.12 g/kg Not Available Not Available
Cmpnds) established established established CHROMATE
7789-06-2 7789-06-2
0.05 mg/m3
(As Chromates) * Not Not Not TITANIUM DIOXIDE 3-7 10.00 g/kg Not Available Not Available
7789-06-2 established established established 13463-67-7
ISOPROPYL 3-7 4.40 g/kg 12.80 g/kg 72.60 mg/l 4 hr
ALCOHOL
Key: ACGIH=American Conference of Governmental Industrial 67-63-0
Hygienists; OSHA=Occupational Safety and Health Administration; PROPYLENE 1-5 5.20 g/kg 13.00 g/kg 54.60 mg/l 4 hr
TLV=Threshold Limit Value; TWA=Time Weighted Average; GLYCOL
PEL=Permissible Exposure Limit (1989 Vacated values); IPEL=Internal MONOMETHYL
Permissible Exposure Limit; Ceiling=TLV or PEL Ceiling Limit; STEL=TLV ETHER
107-98-2
or PEL Short-Term Exposure Limit; Skin= Skin Absorption Designation.
TOLUENE 1-5 .64 g/kg 8.39 g/kg 12.50 mg/l 4 hr
[C- Ceiling Limit; S-Potential Skin Absorption; R-Respirable Dust]
108-88-3
Additional Information Not applicable.
ETHYL 3- 1-5 5.00 g/kg 10.00 g/kg Not Available
ETHOXYPROPANO
SECTION 9 - PHYSICAL & CHEMICAL PROPERTIES ATE
763-69-9
(FORMULA VALUES, NOT SALES SPECIFICATIONS)
XYLENES 0.5-1.5 4.30 g/kg 1.70 g/kg 21.88 mg/l 4 hr
SPECIFIC GRAVITY: 1.230
1330-20-7
PHYSICAL STATE: Liquid
CARBON BLACK 0.1-1.0 15.40 g/kg 3.00 g/kg Not Available
Percent Solids: 51.61
1333-86-4
Percent Volatile by Volume: 70.310 ETHYL BENZENE 0.1-1.0 3.50 g/kg 17.80 g/kg Not Available
pH: Not available. 100-41-4
ODOR THRESHOLD: Not available.
__________________________________________________________________
Page 4 of 7
_______________________________________________________________________________________________________________
Refinish Products
19699 Progress Drive
Strongsville, OH 44149
Product ID: DP40 (0808)
PRODUCT NAME: NON SANDING EPOXY PRIMER
CHRONIC TOXICITY NOS Technical Name: None
Ingredient Target Organ/Chronic Effects: Hazard Class: 3
- Respiratory sensitizer - Mutagen - Ear - Kidney - Liver - Fetotoxin - Subsidiary Class(es): None
Embryotoxin - Teratogen - Brain - Central nervous system - Carcinogen - UN Number: UN1263
Lung Packing Group: II
Mutagenicity Toxicity: USA - RQ Hazardous Substances: Strontium Chromate, Xylenes,
This has not been tested for this product. Toluene, Methyl Ethyl Ketone
Reproductive Toxicity: USA-RQ Hazardous Substance Strontium Chromate>143.2 Pounds,
This has not been tested for this product. Threshold Ship Weight: Xylenes>8546.15 Pounds,
Toluene>25316.71 Pounds
Marine Pollutant Name: None
SUPPLEMENTAL HEALTH INFORMATION:
USA Shipments Only - RQ Threshold Ship Weight: This is the total
Material/ Percent
weight of this product that must be shipped to exceed the RQ quantity.
CAS Ingredient Specific Animal Data:
Number
METHYL 10 - 30 This product contains methyl ethyl ketone (MEK). MEK
ETHYL has been shown to cause minor embryotoxic/fetotoxic
KETONE effects in laboratory animals exposed for prolonged
SECTION 15 - REGULATORY INFORMATION
78-93-3 periods at high concentrations via inhalation. The
INVENTORY STATUS
potential for human exposure to high concentrations is
U.S. TSCA: This product and/or all of its components are listed on the
expected to be low due to the irritating effects of MEK at
U.S. TSCA Inventory or is otherwise exempt from TSCA Inventory
low concentrations.
reporting requirements.
TITANIUM 3-7 This product contains titanium dioxide. Animals inhaling
DIOXIDE massive quantities of titanium dioxide dust in a long-term FEDERAL REGULATIONS
13463-67-7 study developed lung tumors. Studies with humans US Regulations
involved in manufacture of this pigment indicate no
increased risk of cancer from exposure.
CARBON 0.1-1.0 This product contains carbon black which has been rated
BLACK an IARC 2B carcinogen due to animal data.
1333-86-4
ETHYL 0.1-1.0 Ethylbenzene has been reported by NTP to cause cancer
BENZENE in laboratory animals following a chronic (2 year)
100-41-4 inhalation exposure. Dose levels of 75, 250 and 750 ppm
were used, with evidence of carcinogenicity found in the
kidneys of rats and the lung and liver of mice at 750 ppm.
The No Observed Effect Level (NOEL) was 75 ppm. The
relevance of these findings to humans is uncertain, but
appropriate safeguards should be employed to reduce or
eliminate inhalation exposure to ethylbenzene.
SECTION 12 - ECOLOGICAL INFORMATION
POTENTIAL ENVIRONMENTAL EFFECTS
Ecotoxicity: No Information Available.
ENVIRONMENTAL FATE
Mobility: No information available.
Biodegradation: No information available.
Bioaccumulation: No Information Available.
PHYSICAL/CHEMICAL
Hydrolysis: No information available.
Photolysis: No information available.
SECTION 13 - DISPOSAL CONSIDERATIONS
Provide maximum ventilation, only personnel equipped with proper
respiratory and skin and eye protection should be permitted in the area.
Take up spilled material with sawdust, vermiculite, or other absorbent
material and place in containers for disposal.
Waste material must be disposed of in accordance with federal, state,
provincial and local environmental control regulations. Empty containers
should be recycled by an appropriately licensed reconditioner/salvager or
disposed of through a permitted waste management facility. Additional
disposal information is contained on the Environmental Data Sheet for
this product, which can be obtained from your PPG representative.
SECTION 14 - TRANSPORTATION INFORMATION
Proper Shipping Name: Paint
__________________________________________________________________
Page 5 of 7
_______________________________________________________________________________________________________________
Refinish Products
19699 Progress Drive
Strongsville, OH 44149
Product ID: DP40 (0808)
PRODUCT NAME: NON SANDING EPOXY PRIMER
STATE/PROVINCIAL REGULATIONS
Material/ Percent
CAS Number CERCLA HS - SARA EHS- SARA 313 CALIFORNIA PROP. 65: WARNING: This product contains a
RQ (LBS) TPQ (LBS) chemical(s) known to the State of California to cause cancer and birth
METHYL ETHYL 10 - 30 5000 lbs Not Listed Not Listed defects or other reproductive harm.
KETONE
Additional Information
78-93-3
Percent
Material/
EPOXY RESIN 7 - 13 Not Listed Not Listed Not Listed
CAS Number IARC IARC IARC ACGIH NTP OSHA
25068-38-6
Group Group 2B ( Carc. Known Carc.
BARIUM SULFATE 7 - 13 Not Listed Not Listed Not Listed
1(Kno 2A Suspec Carc.
7727-43-7
wn (Proba ted
ISOBUTYL 5 - 10 5000 lbs Not Listed Not Listed
Human ble Carc.)
ACETATE
Carc.) Carc.)
110-19-0 3-7
STRONTIUM N N N Y *Y Y
N-BUTYL ACETATE 5 - 10 5000 lbs Not Listed Not Listed
CHROMATE
123-86-4
7789-06-2
STRONTIUM 3-7 10 lbs Not Listed Not Listed 3-7
TITANIUM DIOXIDE N N Y N N N
CHROMATE
13463-67-7
7789-06-2 0.1-1.0
CARBON BLACK N N Y N N Y
TITANIUM DIOXIDE 3-7 Not Listed Not Listed Not Listed
1333-86-4
13463-67-7 0.1-1.0
ETHYL BENZENE N N Y N N Y
TALC 3-7 Not Listed Not Listed Not Listed
100-41-4
14807-96-6 0.1-1.0
QUARTZ Y N N Y N Y
ISOPROPYL 3-7 Not Listed Not Listed Not Listed
14808-60-7
ALCOHOL 0.1-1.0
ZINC POTASSIUM N N N Y N N
67-63-0
CHROMATE
VINYL RESIN 1-5 Not Listed Not Listed Not Listed
11103-86-9
25086-48-0
PROPYLENE 1-5 Not Listed Not Listed Not Listed
GLYCOL Key: IARC- International Agency on the Research of Cancer; ACGIH-
MONOMETHYL
American Conference of Governmental Industrial Hygienists; NTP-
ETHER
National Toxicology Program *Denotes chemical as NTP Known
107-98-2
Carcinogen; + Denotes NTP Possible Carcinogen; OSHA-
TOLUENE 1-5 1000 lbs Not Listed Listed
Occupational Safety and Health Administration.
108-88-3
ETHYL 3- 1-5 Not Listed Not Listed Not Listed
ETHOXYPROPANO
SECTION 16 - OTHER INFORMATION
ATE
763-69-9
Hazard Rating Systems
XYLENES 0.5-1.5 100 lbs Not Listed Listed
NFPA Rating: 3 30
1330-20-7
HMIS Rating: 3*30
CARBON BLACK 0.1-1.0 Not Listed Not Listed Not Listed
1333-86-4
ETHYL BENZENE 0.1-1.0 1000 lbs Not Listed Listed Rating System: 0=Minimal, 1=Slight, 2=Moderate, 3=Serious, 4=Severe,
100-41-4 *=Chronic Effects.
QUARTZ 0.1-1.0 Not Listed Not Listed Not Listed
14808-60-7
HMIS=Hazardous Materials Identification System; NFPA=National Fire
ZINC POTASSIUM 0.1-1.0 Not Listed Not Listed Not Listed
CHROMATE Protection Association;
11103-86-9
(As Chromium (VI) * Not Listed Not Listed Listed Safe handling of this product requires that all of the information on the
Cmpnds)
MSDS be evaluated for specific work environments and conditions of use.
11103-86-9
(As Zinc Cmpnds) * Not Listed Not Listed Listed
11103-86-9 PREPARED BY: Product Safety Department
(As Chromium * 1 lb Not Listed Listed
REASON FOR REVISION: Section 11 has been updated. Section 1 has
Cmpnds)
been updated. Section 15 has been updated. Section 3 has been
11103-86-9
updated. Section 4 has been updated. Section 5 has been updated.
(As Chromium (VI) * Not Listed Not Listed Listed
Section 6 has been updated. Section 13 has been updated. Section 7 has
Cmpnds)
been updated. Section 8 has been updated. Section 9 has been updated.
7789-06-2
Section 10 has been updated. Section 14 has been updated. Date.
(As Chromium * 1 lb Not Listed Listed
Cmpnds) Edition.
7789-06-2 Updated MSDS
format.
SARA 311/312
This Material Safety Data Sheet has been prepared in accordance with
Health (acute): Yes
Canada's Workplace Hazardous Materials Information System (WHMIS)
Health (chronic): Yes
and the OSHA Hazard Communication Standard (29 CFR 1910.1200),
Fire (flammable): Yes
the supplier notification requirements of SARA Title III, Section 313 and
Pressure: No
other applicable right-to-know regulations.
Reactivity: No
Additional environmental information is contained on the Environmental
WHMIS HAZARD CLASS: - Class B, Division 2 - Class D, Division 2,
Data Sheet for this product, which can be obtained from your PPG
Subdivision A - Class D, Division 2, Subdivision B
representative.
DP40 000006 (00421680.004)(06/28/07)
__________________________________________________________________
Page 6 of 7
_______________________________________________________________________________________________________________
Refinish Products
19699 Progress Drive
Strongsville, OH 44149
Product ID: DP40 (0808)
PRODUCT NAME: NON SANDING EPOXY PRIMER
060821, 000, 0808
*** END OF MSDS ***
__________________________________________________________________
Page 7 of 7
|