MATERIAL SAFETY DATA SHEET
Page: 1
GENERIC MSDS FOR LACQUER
12/20/2007
PRODUCT NAME: GENERIC MSDS FOR LACQUER HMIS CODES: H F R P
FORMULA KEY: CUSTOM AEROSOL PRO 230I
================== SECTION I - MANUFACTURER IDENTIFICATION =================
MANUFACTURER'S NAME: Custom Aerosol Inc.
ADDRESS : 10010 Rearwin Dr
: McKinney, TX 75070
EMERGENCY PHONE : 1-972-346-2700 DATE PRINTED : 12/20/2007
INFORMATION PHONE : 1-972-346-2700 NAME OF PREPARER : Preston Staley
========== SECTION II - HAZARDOUS INGREDIENTS/SARA III INFORMATION =========
VAPOR PRESSURE WEIGHT
REPORTABLE COMPONENTS CAS NUMBER mm Hg @ TEMP PERCENT
-------------------------------------------------------------------------------------------------------------------------------
ACETONE 67-64-1 181.7 20 C 25.05
OSHA PEL: 750 PPM
ACGIH TLV: 500 PPM
* XYLOL 1330-20-7 8 68 DEG F 22.90
OSHA PEL/TWA IS 100PPM
ACGIH TLV/TWA IS 100 PPM
ACGIH TLV/STEL IS 100 PPM
1-METHOXY 2-PROPYL ACETATE 108-65-6 4.9 20 DEG C 3.95
ACGIH (THV) : NOT ESTABLISHED
OSHA PEL : NOT ESTABLISHED
* ## ETHYL BENZENE 100-41-4 7.1 20 DEG C 3.10
OSHA PEL: 100 PPM
ACGIH TLV: 125 PPM
* METHYL ETHYL KETONE 78-93-3 83 75 F 1.85
OSHA PEL: 200 PPM
ACGIH TWA: 200 PPM
MINERAL SPIRITS 8052-41-3 5 100 F 1.80
OSHA PEL: 100 PPM
ACGIH TLV: 100 PPM
* ETHYLENE GLYCOL N-BUTYL ETHER 111-76-2 .88 25 C .95
EB ETHYLENE GLYCOL BUTYL ETHER 111-76-2 88 25 DEG C .55
OSHA PEL: 50 PPM
## BLACK 1333-86-4 3 68 F .40
BLACK PIGMENT IS A SOLID NOT A LIQUID.
OSHA PEL 3.5mg/m3
ACGIH TLV 3.5mg/m3
GLYCOL ETHER PM 107-98-2 88 25 DEG C .25
OSHA PEL: 50 PPM
* TOLUOL 108-88-3 24 20 DEG C .10
OSHA PEL= 200 PPM
ACGIH PEL= 100 PPM
* Indicates toxic chemical(s) subject to the reporting requirements of section 313 of Title III and of 40 CFR 372.
## This product has been reported to cause cancer in laboratory animals. The relevance of these findings to humans is
uncertain, but appropriate safeguards should be employed to reduce or eliminate exposure.
=============== SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS ============
BOILING RANGE: 133 DEG F - 355 F WEIGHT PER GALLON: 7.22 lb/gl
MATERIAL SAFETY DATA SHEET
Page: 2
GENERIC MSDS FOR LACQUER
12/20/2007
VAPOR DENSITY: HEAVIER THAN AIR EVAPORATION RATE: SLOWER THAN ETHER
COATING V.O.C.: 3.517 lb/gl MATERIAL V.O.C.: 2.562 lb/gl
(WITHOUT EXEMPT SOLVENTS) (WITH EXEMPT SOLVENTS)
APPEARANCE AND ODOR:
Viscous liquid with an odor characteristic of the solvents listed in Section II.
================= SECTION IV - FIRE AND EXPLOSION HAZARD DATA ==============
FLASH POINT: -4 F METHOD USED: TCC
FLAMMABLE LIMITS IN AIR BY VOLUME- LOWER: .8 UPPER: 13.1
EXTINGUISHING MEDIA:
Use National Fire Protection Association (NFPA) Class B extinguisher (CarbonDioxide, dry, chemical, or universal aqueous
film forming foam) designed to extinquish NFPA Flammable liquid fires.
SPECIAL FIREFIGHTING PROCEDURES:
Water spray may be ineffective. Water spray may be used to cool closed containers to prevent pressure build-up and
possible autoignition or explosion when exposed to extreme heat. If water is used, fog nozzles are preferrable. Fire-
fighters should wear self contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Contents under pressure. Do not use or store near sources of heat, sparks or open flame. Keep away from any source of
heat such as sunlight, heaters or stoves that could cause the container to burst. Do not puncture or incinerate. Do
not crush or place in a garbage compactor. Do not store above 120 degrees F. Aerosol containers may explode when
exposed to extreme heat. Product vapors are heavier than air and may travel a long distance to a source of ignition and
flash back.
======================== SECTION V - REACTIVITY DATA =======================
STABILITY:
Stable at normal temperatures.
CONDITIONS TO AVOID:
Avoid contact with strong alkalis, strong mineral acids, or strong oxidizing agents. Avoid high temperatures, direct
heating.
HAZARDOUS DECOMPOSITION OR BYPRODUCTS:
May produce hazardous decomposition products when heated. Welding, brazing, or flame-cutting on surfaces coated with
this product may produce fumes including: Carbon Monoxide or Carbon Dioxide.
HAZARDOUS POLYMERIZATION:
Not expected to occur.
==================== SECTION VI - HEALTH HAZARD DATA =======================
INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
Vapor and spray mist may be harmful if inhaled. Vapor irritates eyes, nose, and throat. Repeated exposure to high vapor
concentrations may cause irritation of the respiratory system and permanent brain and nervous system damage.
Intentional misuse by deliberately inhaling the contents can be harmful or fatal.
SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
Eye contact: causes eye irritation. May experience itching, burning sensation and visual disturbances.
SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
May cause moderate skin irritation. May be harmful if absorbed through the skin. Dryness, itching, cracking, burning,
redness, and swelling are conditions associated with excessive skin contact.
INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
MATERIAL SAFETY DATA SHEET
Page: 3
GENERIC MSDS FOR LACQUER
12/20/2007
Harmful or fatal if swallowed.
HEALTH HAZARDS (ACUTE AND CHRONIC):
Avoid long term and repeated contact.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:
Not applicable.
EMERGENCY AND FIRST AID PROCEDURES:
INGESTION: If swallowed, have conscious patient drink several glasses of water. Induce vomiting if conscious. Keep head
below hips to prevent aspiration of liquid into lungs. Get medical help immediately. EYES: In case of eye contact, flush
eyes immediately with plenty of water for at least 15 minutes. SKIN: In case of skin contact, remove promptly by
wiping, followed by waterless hand cleaner and soap and water. INHALATION: If affected by inhalation of vapor or spray
mist, remove to fresh air. Apply artificial respiration and other supportive measures as required. Get medical
attention.
=========== SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE ============
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Provide maximum ventilation. Only personnel equipped with proper respiratory and skin and eye protection should be
permitted in the area. Remove all sources of ignition. Take up spilled material with sawdust, vermiculite, or other
absorbent material and place into containers for disposal.
WASTE DISPOSAL METHOD:
Waste material must be disposed of in accordance with Federal, State, and Local environmental control regulations.
Empty containers should be recycled or disposed of through an approved Waste Management Facility.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING:
Do not store above 120 deg. F. Store large quantities in buildings designed and protected for storage of NFPA Flammable
liquids.
OTHER PRECAUTIONS:
If this material is part of a multiple component coating system, read the MSDS for the other component or components
before blending as the resulting mixture may have the hazards of all of its parts. Containers should be grounded when
pouring. Avoid free fall of liquids in excess of a few inchs. Containers of this material may be hazardous when
emptied since they retain residues. Do not cut, puncture, or weld on or near container.
===================== SECTION VIII - CONTROL MEASURES ======================
RESPIRATORY PROTECTION:
Overexposure to vapors may be prevented by ensuring ventilation controls, vapor exhaust or fresh air entry. If TLV of
any component is exceeded, use an appropriate NIOSH/MSHA approved respirator. Follow respirator manufacturers directions
for respirator use.
VENTILATION:
Provide sufficient mechanical and/or local exhaust ventilation to keep the concentration of ingredients listed in
Section II below the lowest exposure limits.
PROTECTIVE GLOVES:
Impermeable chemical handling gloves for skin protection.
EYE PROTECTION:
Use chemical safety glasses, goggles, and faceshields for eye protection.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT:
Use impermeable aprons and protective clothing whenever possible to prevent skin contact. The use of head caps whenever
possible is strongly recommended. Clean or discard contaminated clothing and shoes.
MATERIAL SAFETY DATA SHEET
Page: 4
GENERIC MSDS FOR LACQUER
12/20/2007
WORK/HYGIENIC PRACTICES:
Eye washes and safety showers in the workplace are recommended.
========================= SECTION IX - TRANSPORTATION INFORMATION ==========
PROPER SHIPPING NAME HAZARD CLASS UN NUMBER PACKING GROUP
========================= SECTION X - DISCLAIMER ==========================
The information and recommendations contained herein are believed to be accurate at the time of preparation or obtained
from sources believed to be generally reliable. Fasse Paint Co. will not be held liable for claims relating to any
party's use of or reliance on information contained herein, regardless of whether it is claimed the information is
inaccurate.
|