Material Safety Data Sheet
Page 1 of 6 Issue date: August 2005
M-BOND 610 ADHESIVE
1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER
Davidson Measurement Pty. Ltd
ACN: 005 031 961 ABN: 29 005 031 961
Phone: 03 9580 4366
Fax: 03 9580 6499
Email: info@davidson.com.au
Web: www.davidson.com.au
Address: 1-3 Lakewood Boulevard,
Braeside, Victoria, 3195.
Product Name: M-BOND 610 ADHESIVE
Manufacturer's Product Code: MGM0012J
Use: Two-component, solvent-thinned, epoxy-phenolic adhesive for high precision transducers.
2. HAZARDS IDENTIFICATION
HAZARDOUS ACCORDING TO EU CRITERIA
Hazard Category: Irritant (Xi), Flammable (F)
Hazard Classification: HAZARDOUS SUBSTANCE, DANGEROUS GOOD
RISK PHRASES
R11 Highly flammable
R19 May form explosive peroxides.
R36/37/38 Irritating to eyes, respiratory system and skin.
R43 May cause sensitisation by skin contact.
SAFETY PHRASES
S9 Keep container in a well ventilated place.
S16 Keep away from sources of ignition - No smoking.
S24/25 Avoid contact with skin and eyes.
S26 In case of contact with eyes, rinse immediately with plenty of water and contact a doctor or Poisons Information
Centre.
S29 Do not empty into drains.
S33 Take precautionary measures against static discharge.
Road Transport
UN Number: 1993
Proper Shipping Name: FLAMMABLE LIQUID, N.O.S.(Contains TETRAHYDROFURAN)
Dangerous Goods Class: 3
Packing Group: II
Poison Schedule: S5 [Aust]
This material is a Scheduled S5 Poison and must be stored, handled and used according to the appropriate regulations.
Warning Statement:
Always maintain adequate ventilation when using this product. Highly flammable liquid, extinguish all ignition sources.
This product may cause sensitisation by skin contact.
3. COMPOSITION / INFORMATION ON INGREDIENTS
SUBSTANCE NAME Proportion CAS Number
TETRAHYDROFURAN > 60 % 109-99-9
BISPHENOL F EPOXY RESIN 30 to 60 % 28064-14-4
METHYL ETHYL KETONE 1 to < 10 % 78-93-3
All other ingredients not hazardous according to EU Criteria.
Material Safety Data Sheet
Page 2 of 6 Issue date: August 2005
M-BOND 610 ADHESIVE
4. FIRST AID MEASURES
Swallowed:
If swallowed, DO NOT induce vomiting. If victim conscious, give 1 to 2 glasses of water to drink. Seek urgent medical
assistance.
Eye:
If material is splashed into eyes, flush with plenty of water for at least 15 minutes, ensuring eye lids are held open.
Immediately transport to hospital or doctor.
Skin:
If material is splashed onto the skin, remove any contaminated clothing and wash skin thoroughly with soap and water.
If irritation persists immediately transport to hospital or doctor.
Inhaled:
Remove victim to fresh air. Apply resuscitation if victim is not breathing - Administer oxygen if breathing is difficult.
Transport to hospital or doctor immediately.
First Aid Facilities:
Eye wash fountain, safety shower and normal wash room facilities.
Advice to Doctor:
Treat symptomatically.
In case of poisoning, contact Poisons Information Centre
In Australia call Tel: 131126
In New Zealand Tel: 034747000
5. FIRE-FIGHTING MEASURES
Fire/Explosion Hazard
SUITABLE EXTINGUISHING MEDIA: Foam, dry chemical or carbon dioxide.
HAZARDS FROM COMBUSTION PRODUCTS: On combustion or on thermal decomposition (pyrolysis), there
will be a release of oxides of carbon and noxious smoke.
PRECAUTIONS FOR FIRE FIGHTERS AND SPECIAL PROTECTIVE EQUIPMENT: Self-contained
breathing apparatus (SCBA) required for fire-fighting personnel. If possible to do so safely, shut off fuel to fire. Avoid
spreading burning liquid with water used for cooling fire exposed containers when using water spray, boil-over may
occur when the product temperature reaches the boiling point of water, thereby resulting in re-ignition.
HAZCHEM CODE: 3[Y]E [Aust]
FLAMMABILITY
Flash Point: - 14掳C
Flammability Limits: LEL: 1.8 % UEL: 11.8 %
Auto-ignition Temperature: 320掳C
6. ACCIDENTAL RELEASE MEASURES
Emergency Procedures:
Flammable liquid. Ventilate area. Avoid all sources of ignition. Keep unnecessary people away; Isolate hazard area and
deny entry. Wear suitable protective equipment as outlined under personal protection in this MSDS.
Methods and Materials for Containment and Clean Up Procedures:
Throw diatomaceous earth onto spill. DO NOT use sawdust. Use non-sparking tools or HEPA vacuum system to pick
up. Place into properly labeled drum for later disposal.
Emergency information(Transport):
Dangerous Goods - Initial Emergency Response Guide (SAA/SNZ HB76:1997)
For LIQUIDS - Highly Flammable, Guide No: 14
Material Safety Data Sheet
Page 3 of 6 Issue date: August 2005
M-BOND 610 ADHESIVE
7. HANDLING AND STORAGE
Precautions for Safe Handling:
Highly Flammable liquid. Avoid ignition sources. Provide adequate ventilation. Avoid exposure by all routes.
Conditions for Safe Storage:
Keep containers tightly closed, when not using the product. Store in original packages as approved by manufacturer.
Store in an area that is dry and well-ventilation away from ignition sources. Store below 25掳C. Can react vigorously
with strong oxidizing agents, strong Lewis or mineral acids, and strong mineral and organic bases; especially primary
and secondary aliphatic amines. For further information please refer to the Engineering Controls of this MSDS.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Exposure Standards
No exposure standards are available for this product, however, the following exposure standards have been assigned by
[NOHSC] to the following components of the product:
TETRAHYDROFURAN
[NOHSC]
[TWA]100 ppm 295 mg/m3
Notices: Sk
Sk Notation:
The main route of most hazardous substances into the body is via inhalation, however, certain substances such as
ethylene glycol monoethyl ether can readily penetrate the skin, with resultant toxic effects. The notice 'Sk' indicates that
absorption can occur through the skin.
METHYL ETHYL KETONE
[NOHSC]
[TWA]150 ppm 445 mg/m3
[STEL]300 ppm 890 mg/m3
References: A
BIS PHENOL F EPOXY
[NOHSC]
No exposure standards.
Notices: Sen
Sen Notation:
Some substances can cause a specific immune response in some people. Such substances are called sensitisers and the
development of a specific immune response is termed 'sensitisation'. Exposure to a sensitiser, once sensitisation has
occurred, may manifest itself as a skin rash or inflammation or as an asthmatic condition, in many situations, only a
small dose which may be far below a TWA or STEL, in some susceptible individuals this may trigger violent and
severe adverse reactions.
Engineering Controls
Highly flammable liquid. Maintain adequate ventilation at all times. Prevent accumulation of vapours in hollows or
sumps. Eliminate any sources of ignition.
Material Safety Data Sheet
Page 4 of 6 Issue date: August 2005
M-BOND 610 ADHESIVE
8. EXPOSURE CONTROLS / PERSONAL PROTECTION (Continued)
Personal Protection Equipment
GLOVES: Butyl rubber, nitrile rubber.
EYES: Chemical goggles or spectacles with side shields to protect eyes.
RESPIRATORY PROTECTION: Avoid breathing of vapours. Filter capacity and respirator type depends on
exposure levels and type of contaminant. Select and use respirators in accordance with AS/NZS 1715/1716. When
vapours exceed the exposure standards then the use of a half-face respirator fitted with an organic vapour cartridge is
recommended. If entering confined spaces or if unknown levels of contaminate are a potentiality, then the use of a
Self-contained breathing apparatus (SCBA) with positive pressure air supply complying with AS/NZS 1715 / 1716, or
any other acceptable International Standard is recommended.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Colorless liquid; ether-like odor.
Boiling Point: 66掳C
Vapour Pressure: 129 mmHg @ 20掳C
Specific Gravity: 0.90
Flash Point: - 14掳C
Flammability Limits: LEL: 1.8 % UEL: 11.8 %
Solubility in Water: Soluble (50 %).
Other Properties
Vapor Density (Air = 1): 2.4
Evaporation Rate (BuAc = 1): 8.0
Volatile Organic Compounds: 712g/liter
Autoignition Temperature: 320掳C
10. STABILITY AND REACTIVITY
CHEMICAL STABILITY:
Stable under normal conditions of use.
CONDITIONS TO AVOID:
Ignition sources and mixing with incompatibles.
INCOMPATIBLE MATERIALS:
Strong mineral acids (sulfuric, nitric and hydrochloric), and oxidizing agents.
HAZARDOUS DECOMPOSITION PRODUCTS:
Oxides of carbon, aldehydes and acids may be formed during combustion. Reaction with some curing agents may
produce considerable heat.
HAZARDOUS REACTIONS:
Under appropriate conditions this product may rapidly and uncontrollably polymerise releasing heat, and potential
ignition and propagation of fire may result.
11. TOXICOLOGICAL INFORMATION
No adverse health effects are expected, if the product is handled in accordance with this Material Safety Data Sheet and
the product label. Symptoms and effects that may arise if the product is mishandled and overexposure occurs are:
ACUTE HEALTH EFFECTS:
Swallowed:
May cause irritation to mouth, throat and stomach with effects including pains in the stomach, which may lead to
nausea, vomiting and diarrhoea.
Eye:
Will cause irritation to the eyes, with effects including: tearing, pain, stinging and blurred vision.
Material Safety Data Sheet
Page 5 of 6 Issue date: August 2005
M-BOND 610 ADHESIVE
11. TOXICOLOGICAL INFORMATION (Continued)
Skin:
Will cause irritation to the skin, with effects including; Redness, itchiness, and drying/defatting.
Inhaled:
Mists or vapours will cause irritation to the nose, throat and respiratory system with effects including: Dizziness,
headache, coughing, loss of co-ordination and chest pains.
Chronic:
Prolonged or repeated skin contact may lead to dermatitis. Prolonged or repeated contact with this substance will cause
sensitisation by skin contact.
Methyl Ethyl Ketone:
Inhalation LC50(rat): 23,500 mg/m3/8H
Oral LD50(rat): 2,737 mg/kg
12. ECOLOGICAL INFORMATION
No information is available for this product, however, large quantities should not be discharged to waterways, sewers or
drains.
13. DISPOSAL CONSIDERATIONS
Refer to appropriate authority in your State. Dispose of material through a licensed waste contractor. Advise flammable
and irritant nature. If large amounts of the product enter waterways, sewers or streams, immediately contact the
Environmental Protection Agency or your Local Waste Management Authority.
14. TRANSPORT INFORMATION
Road Transport
UN Number: 1993
Proper Shipping Name: FLAMMABLE LIQUID, N.O.S.(Contains TETRAHYDROFURAN)
Dangerous Goods Class: 3
Packing Group: II
Label: Irritant (Xi), Flammable (F)
Air Transport
UN Number: 1993
Proper Shipping Name: FLAMMABLE LIQUID, N.O.S.(Contains TETRAHYDROFURAN)
Dangerous Goods Class: 3
Packing Group: II
Label: Irritant (Xi), Flammable (F)
Sea Transport
UN Number: 1993
Proper Shipping Name: FLAMMABLE LIQUID, N.O.S.(Contains TETRAHYDROFURAN)
Dangerous Goods Class: 3
Packing Group: II
Label: Irritant (Xi), Flammable (F)
Material Safety Data Sheet
Page 6 of 6 Issue date: August 2005
M-BOND 610 ADHESIVE
15. REGULATORY INFORMATION
Poison Schedule: S5 [Aust]
This product is a Scheduled (S5) Poison and must be stored, handled and used according to the appropriate regulations.
Inventory Status:
Australia (AICS) Y
Europe (EINECS/ELINCS) Y
Y = all ingredients are on the inventory.
16. OTHER INFORMATION
Date of Preparation:
Issue date: August 2, 2005 Supercedes: March 30, 2003
Reasons for Update:
nd
1. Alignment with the 2 Edition of National Code of Practice for the Preparation of Material Safety Data Sheets
[NOHSC:2001(2003)].
2. Changes and /or addition made to all sections.
Key Legend Information:
NOHSC - National Occupational Health & Safety Commission [Aust]
SUSDP - Standard for the Uniform Scheduling of Drugs and Poisons [Aust]
TWA - Time Weighted Average [Int]
STEL - Short Term Exposure Limit [Int]
AICS - Australian Inventory of Chemical Substances
EPA - Environmental Protection Agency [Int]
AS/NZS 1715 - Selection, use and maintenance of respiratory protective devices. [Aust/NZ]
AS/NZS 1716 - Respiratory protective devices. [Aust/NZ]
(SAA/SNZ HB76:1997) - Dangerous Goods - Initial Emergency Response Guide [Aust/NZ]
AS 1940 - The Storage and Handling of Flammable and Combustible Liquids [Aust]
Hazchem Code: Designation for fire fighters [Aust]
IATA - International Aviation Transport Authority [Int]
ICAO - International Civil Aviation Organization [Int]
IMO - International Maritime Organisation. [Int]
IMDG - International Maritime Dangerous Goods [Int]
United Nations Recommendations for the Transport of Dangerous Goods and Globally Harmonized System for the
classification and labelling of Chemicals. [Int]
EU - European Union [Int]
[Aust/NZ] = Australian/New Zealand
[Int] = International
[US] = United States of America
Principal References:
Information supplied by manufacturer.
Disclaimer
To the best of our knowledge, the information provided above meets the requirements of European Union directives for
hazardous substances which have been tested as a whole. The data provided on this Material Safety Data Sheet is from
manufacturers of the original components. All animal test data has been obtained from the public domain, NO
ANIMAL TESTS have been conducted by Davidson Pty Ltd. Davidson Pty Ltd specifically disclaims any and all form
of liability and/or responsibility for the application of this product.
END of MSDS
|